COYOTE ROLLER 916 Chain Link Installation Guide

: June 15, 2024
: COYOTE ROLLER

Table of Contents

WARNING
BEFORE YOU BEGIN
BRACKET ORIENTATION
TOOLS NEEDED
CUTTING ROLLERS
END CAP INSTALLATION
END CAP REMOVAL
PRO TIPS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

COYOTE ROLLER 916 Chain Link

WARNING

THIS KIT CONTAINS PRODUCTS THAT HAVE SHARP EDGES. PLEASE USE CAUTION WHEN HANDLING. USE EYE, EAR, AND HAND PROTECTION AT ALL TIMES DURING INSTALLATION.
KITS CONTAINS SMALL PIECES THAT MAY BECOME A CHOCKING HAZARD. KEEP OUT OF REACH OF CHILDREN.
PRODUCT IS NOT DESIGNED FOR HUMAN USE. DO NOT ATTEMPT TO CLIMB FENCE ONCE ROLLERS ARE INSTALLED. DO NOT HANG ON ROLLERS, ROLL GUARD INC. WILL NOT BE HELD LIABLE FOR DAMAGE, INJURY, OR DEATH CAUSED BY IMPROPER USE OR INSTALLATION OF THIS PRODUCT.

BEFORE YOU BEGIN

UNBOXING

AFTER YOUR ORDER ARRIVES, PLEASE CHECK TO MAKE SURE ALL ROLLERS, BRACKETS, END CAPS, AND HARDWARE ARE PRESENT AND IN THE CORRECT COLOR.

IF ANY PIECES ARE MISSING OR INCORRECT, PLEASE REACH OUT TO US DIRECTLY AT: SALES@COYOTEROLLER.COM

LAYOUT

MAKE SURE THERE ARE NO OBJECTS NEAR THE FENCE THAT WILL AID ANIMALS IN GETTING OVER (SHED, ROCKS, BUCKETS, ETC). WE RECOMMEND A MINIMUM FENCE HEIGHT OF 6FT FOR OPTIMAL EFFECTIVENESS.

PLEASE TAKE INTO CONSIDERATION HOW MANY ROLLERS AND BRACKETS WILL BE NEEDED FOR EACH SECTION. IF ANY OF THE ROLLERS WILL NEED TO BE CUT, CONSIDER ALTERNATE MOUNTING OPTIONS BELOW FOR BEST APPEARANCE.

*KEEP IN MIND ALL ROLLERS ARE SOLD IN 4FT LENGTHS.

1: LESS AESTHETICALLY PLEASING (QUICKEST)

2: BETTER LOOKING (MINIMAL EXTRA EFFORT)

3: BEST LOOKING (MORE CUTTING)

BRACKET ORIENTATION

LEFT AND RIGHT BRACKETS ARE TO BE USED AS A “CENTER” BRACKET, AND ONLY ONE IS NEEDED BETWEEN ROLLERS. BE SURE TO ALTERNATE L & R BRACKETS WHEN USING AS A “CENTER” SO YOU DON’T RUN OUT OF ONE SIDE PREMATURELY.

Top Hole is not used for installation on chain link. Use bottom hole to mount bracket to brace band

TOOLS NEEDED

LEVEL
9/16” WRENCH OR RATCHET W/DEEP SOCKET
PLIERS
HACKSAW OR CHOP SAW WITH A FINE TOOTH NON-FERROUS BLADE
RUBBER MALLET
DE-BURRING TOOL OR FILE
PPE- GLOVES, GLASSES, EAR PLUGS

STEP 1: BRACKET PLACEMENT

START AT THE LEFT SIDE OF YOUR FENCE AND PLACE THE FIRST BRACE BAND OVER THE TOP RAIL AS CLOSE TO THE EDGE AS POSSIBLE.

*BRACE BANDS CAN BE DIFFICULT TO OPEN. WE RECOMMEND PLACING THE BAND OPENINGS ON THE TOP RAIL, AND WITH A MALLET HITTING THEM ON THE BACK SIDE TO SPREAD THE ENDS OPEN AND OVER THE FENCE.

ALTERNATIVELY, YOU CAN USE TWO PAIRS OF PLIERS TO MANUALLY OPEN THE ENDS.

ONCE THEY ARE INSTALLED ON THE FENCE, YOU CAN USE A PAIR OF PLIERS TO CLOSE THEM BACK UP TO MAKE INSTALLING THE HARDWARE EASIER.

STEP 2: HARDWARE INSTALLATION

ONCE BRACE BAND HAS BEEN PLACED OVER THE TOP RAIL INSTALL THE BRACKET AND HARDWARE AS SEEN BELOW

WE RECOMMENDED INSTALLING THE BRACKETS AT A 45 DEGREE ANGLE OUTWARD (FOR COYOTES) AND INWARD (FOR PETS). IF THIS IS NOT POSSIBLE, MOUNTING THE BRACKETS VERTICALLY WILL ALSO WORK.

TIGHTEN THE HARDWARE WITH A 9/16” WRENCH OR RATCHET. BE CAREFUL WHILE TIGHTENING AS THE BRACKETS AND BRACE BANDS HAVE A TENDANCY TO MOVE DURING THIS PROCESS.

STEP 3: INSTALLING THE FIRST ROLLER

INSTALL THE NEXT BRACE BAND, BRACKET, AND HARDWARE LOOSLY ABOUT 4FT PAST YOUR FIRST. PLACE A ROLLER ON THE PREVIOUSLY MOUNTED BRACKET TILL THE END OF THE ROLLER TOUCHES THE ARM OF THE BRACKET. WHILE HOLDING THE ROLLER, SLIDE THE SECOND BRACKET ON THE OPPOSITE END AND ADJUST SO YOU HAVE A 1/4” GAP BETWEEN THE RIGHT SIDE OF THE ROLLER AND THE ARM OF THE BRACKET (SEE PIC BELOW). ONCE IN PLACE, TIGHTEN THE SECOND BRACKET ASSEMBLY. REPEAT THIS PROCESS ALONG THE ENTIRE FENCE.

CUTTING ROLLERS

COYOTE ROLLERS HAVE BEEN DESIGNED SO THEY CAN BE CUT DOWN TO AS SMALL AS 2”.
THEY CAN BE CUT ON ANY PORTION OF THE ROLLER.
FOR THE CLEANEST AND STRAIGHTEST CUT WE RECOMMEND USING A CHOP SAW WITH A FINE TOOTH NON-FERROUS METAL BLADE. THIS WILL LEAVE MINIMAL BURRS AND SHARP EDGES.

OPTIONALLY YOU CAN USE A BASIC HACKSAW WITH A METAL BLADE. THIS DOESN’T ALWAYS CUT PERFECTLY STRAIGHT, BUT IT WILL GET THE JOB DONE.

ONCE CUT YOU WILL WANT TO TAKE A DEBURRING TOOL OR FILE TO CLEAN UP ANY SHARP EDGES OR METAL FILINGS STUCK TO THE END OF THE ROLLER.

BEFORE CUTTING YOUR ROLLER, KEEP IN MIND THAT EACH END CAP ADDS 1/4” TO THE LENGTH OF THE ROLLER ONCE INSTALLED.

END CAP INSTALLATION

END CAP INSTALLATION IS AN EASY PROCESS ONLY REQUIRING A RUBBER MALLET. BE SURE THE ROLLER IS FREE OF METAL BURRS OR FILINGS BEFORE ATTEMPTING ISNTALLATION. WITH THE ROLLER END FACING UPWARDS, SEAT THE END CAP INSIDE THE ROLLER. WHILE HOLDING THE ROLLER TAKE A RUBBER MALLET AND HIT THE CAP TILL FULLY SEATED.

END CAP REMOVAL

REMOVING THE END CAPS CAN ONLY BE DONE AFTER A ROLLER IS CUT. THEY ARE A “PRESS FIT” AND NOT POSSIBLE TO REMOVE FROM A 4FT ROLLER WITHOUT DAMAGING THE ROLLER, END CAP, OR BOTH.

ONCE THE ROLLER IS CUT TO LENGTH, USE A BROOM HANDLE, SHOVEL HANDLE, OR 1” PVC PIPE LONG ENOUGH TO REACH THE BACK SIDE OF THE END CAP INSIDE THE ROLLER. PLACE THE HANDLE ON THE GROUND AND SLIDE THE ROLLER FORCEFULLY DOWN UNTIL IT COMES INTO CONTACT WITH THE END CAP. THIS MAY TAKE SEVERAL TRIES, BUT THE END CAP WILL EVENTUALLY POP OUT.

PRO TIPS

CUTTING THE ROLL PIN:

TO GET YOUR BRACKETS AS CLOSE TO WALLS OR FENCE POSTS AS POSSIBLE, CONSIDER CUTTING ONE SIDE OF THE ROLL PIN. THIS CAN BE ACHIEVED WITH A HACKSAW OR ANGLE GRINDER WITH A CUT OFF WHEEL.

LUBRICANT:

ROLLERS ARE DESIGNED TO SPIN WITH VERY MINIMAL PRESSURE, BUT A GOOD LUBRICANT CAN BE APPLIED INSIDE THE END CAPS DURING INSTALLATION FOR A BUTTERY SMOOTH SPIN. IN ADDITON, USING PETROLEUM JELLY IN COOL CLIMATES CAN REDUCE THE POSSIBILITY OF YOUR ROLLERS FROM FREEZING.