amazon basics B0B5KL4CW8 Car Power Inverter User Manual

amazon basics B0B5KL4CW8 Car Power Inverter

**Important Safeguards

**

Read these instructions carefully and retain them for future use. If this product is passed to a third party, then these instructions must be included.

DANGER: Risk of electric shock!
Keep children away from the product. The product generates the same dangerous AC power as a normal household outlet. This product is not a toy.

WARNING: Risk of fire or explosion!
This product employs components that tend to produce arcs or sparks – To prevent fire or explosion, do not install in compartments containing batteries or flammable materials.

WARNING: Risk of electric shock!
Take special care when working with a vehicle battery.

Remove any jewelry (e.g. watch, bracelet, and ring). Be careful not to short- circuit the battery with any metallic object the battery with any metallic object

WARNING: Risk of chemical burns! Wear eye protection and protective gloves!

Batteries contain corrosive materials. Should battery acid come into contact with skin or eyes, flush it with water and consult a physician.

CAUTION: Risk of fire!
To prevent fire, do not cover or obstruct the ventilation openings. Do not mount in zero-clearance compartment. Overheating may result. Ensure that at least 2″ (5 cm) of clearance around the product.

CAUTION: Risk of fire!
Do not replace any vehicle fuse with a rating higher than recommended by the vehicle manufacturer. This product is rated to convert 12 V DC to 115 V AC. Ensure that the electrical system in your vehicle can supply this product without causing the vehicle fusing to open. This can be determined by making sure the fuse in the vehicle that protects the outlet is rated higher than 68 amperes. Information on the vehicle fuse ratings are typically found in the vehicle operator’s manual. If a vehicle fuse opens repeatedly, do not keep on replacing it. The cause of the overload must be found. On no account should fuses be patched up with tin foil or wire as this may cause serious damage elsewhere in the electrical circuit or cause fire.

CAUTION: The output voltage distortion is not specified if the temperatures measured on loads supplied by the non-sinusoidal waveform do not exceed the temperatures measured using a sinusoidal waveform by more than 5 Kand, in no case, exceed the allowable temperatures specified in the applicable standard for the load device. The following types of load shall be used for the tests:

• line filter capacitor;
• microwave oven;
• fluorescent and high-intensity lamps (with a ballast);
• other loads as necessary based on the intended application of the product; and
• transformerless battery chargers.

1. Do not use the product in a vehicle in which the position(+) pole of the battery is connected to the chassis! Before using the product, determine how the battery is connected in the respective vehicle. If in doubt, refer to vehicle operating instructions.
2. The product must be fastened so that it does not cause a safety hazard in case of collision or hard braking.
3. Route the cable so that it does not interfere with the driver of the vehicle when plugged into the lighter socket.
4. When working with vehicle batteries, always follow the advice from the manufacturer of the battery and in the vehicle operating manual.
5. Never leave the product unattended during operation.
6. This product contains no user-serviceable parts and requires little maintenance. Leave any servicing or repairs to qualified personnel only.
7. Do not attempt to repair the product yourself. In case of malfunction, repairs are to be conducted by qualified personnel only.
8. Do not open the product housing. Do not insert any foreign objects into the inside of the housing.
9. Never use accessories that are not recommended by the manufacturer. They could pose a safety risk to the user and might damage the product. Only use original parts and accessories.
10. The product must only be supplied at safety extra low voltage corresponding to the marking on the product.
11. To avoid damaging the cable, do not squeeze, bend, or drag it over sharp edges. Keep the cable and product away from hot surfaces and open flames.
12. Place the cable in such a way that unintentional pulling or tripping over it is not possible.
13. Do not expose the product to water, rain, or snow.
14. The housing of the product can reach 140 °F (60 °C) after extended high-power operation. Keep the product away from materials that could be affected by high temperatures.
15. Keep the area surrounding the product clear to ensure free air circulation. Do not place items on or over the product during operation. The product will shut down if the internal temperature gets too hot. Restart the product after it cools.
16. Operate the product in ambient temperatures between 32 °F and 104 °F (0 °C and 40 °C).
17. Avoid placing the product on or near heating vents, radiators, or other sources of heat. Do not place the product in direct sunlight (e.g. on the vehicle’s dashboard) to prevent an overheating shutdown caused by high temperatures.
18. The product creates a voltage that is not sinusoidal. Do not use the product with the following equipment:
    • Small, battery-operated appliances such as rechargeable flashlights, shavers, or nightlights are plugged into an AC receptacle to recharge. The device can be damaged if connected to the product. Always recharge batteries using a separate battery charger.
    • Battery chargers for battery packs used with power tools.

Intended Use

• This product is intended to convert an extra low voltage 12 V (direct current) of power sources to the conventional 115 V (alternating current). Do not attempt to connect the product to any other power source, including any AC power source.
• This product is intended to be used in a vehicle to operate different types of appliances that use AC power such as TVs, VCRs, portable computers, power tools, and lights for emergency use.
• This product is intended to be used in indoor and outdoor areas, however it is not water-proof. Keep away from rain.
• Do not connect the product to a battery that has a nominal output other than 12 V. The product will not operate if connected to a 6 V battery and may be damaged if connected to a 24 V or 36 V battery.
• This product is not intended for professional use.
• This product is not intended to be used in connection with life support systems or other medical equipment or devices.

Product Description

• Display
• (on/off) button
• Outlet, x2
• USB port
• Positive(+) terminal
• Red terminal cap
• Fan
• Black terminal cap
• Negative (-) terminal
• Red cable with ring connector
• Black cable with ring connector
• Cigarette lighter cable

Before First Use

CAUTION : Risk of suffocation!
Keep any packaging materials away from children and pets – these materials are a potential source of danger, e.g. suffocation.

• Remove all the packing materials.
• Remove and review all components before use.
• Check the product for transport damages.

Operation

CAUTION : Risk of damage!

• Make sure to connect the red cable to the positive terminal(+) and the black cable to the negative terminal(-). A reverse polarity connection (positive to negative) blows a fuse and may permanently damage the product.
• Loose connectors result in an excessive voltage drop and may result in overheated wires and melted insulation.

NOTICE

• Disconnect the lighter plug or the ring connectors of the cables (J/K) from the battery whenever the engine is switched off for extended periods of time. In some vehicles, the power does not turn off after the engine has been switched off. If the product is left connected, the vehicle battery might become discharged or damaged.
• The product works best with a battery that is in good condition and fully charged.
• Position the product on a flat and stable surface in a dry and well-ventilated location.

Checking the wattage of the devices to be connected

CAUTION: Risk of damage!

• Make sure that the total wattage of the devices to be connected does not exceed the maximum load of the respective outlet. The product automatically shuts down in the event of a power overload.
• Only use the product with the provided cable. For loads under 100 W, use the cigarette lighter cable (L). For loads between 100 Wand 750 W, use the cables with ring connectors (J and K) for direct connection.

NOTICE
When the connected device switches on, there is an initial surge of power (i.e. “starting load” or “peak load”). Once started, it requires less power to operate (i.e. “running load”). Always check the starting and running loads of the motorized devices before connecting to the product to prevent overload shutdown.

See the table below for the estimated wattage required for different devices. Check the actual wattage requirements on the rating label and in the operating instructions of devices to be used.

Take the surge wattage (i.e. starting load) required by electrical motors into consideration as well as the rated wattage (i.e. running load). See the below table as an example for adding up the total wattage of devices to be powered.

NOTICE: The wattage might not be listed on the devices to be connected. In that case, calculate the wattage using the equation “VOLTS x AMPERE = WATTS”

• Formula : 115 Volts x Amperes = XXX Watts
• Example : 115 Volts x 5 Amperes = 600 Watts

Connecting the product to a lighter socket

Risk of damage!

CAUTION:

• The total loads of the connected devices must be under 100 W.
• Always switch the product off and disconnect the cigarette lighter plug from the lighter socket when the product is not in use.

1. Unscrew the red terminal cap (F). Place the red cable connector of the cigarette lighter cable (L) on the red positive terminal(+) (E) with its tip fitted to the slot (Fig. 1 ).
2. Tighten the red terminal cap (F) to clamp the cable connector securely (Fig. 1).
3. Unscrew the black terminal cap (H). Place the black cable connector of the cigarette lighter cable (L) on the black negative terminal (-) (I) with its tip fitted to the slot (Fig. 1 ).
4. Tighten the black terminal cap (H) to clamp the cable connector securely (Fig. 1).
5. Connect the cigarette lighter plug to the lighter socket of the vehicle. Make sure the plug is fully inserted (Fig. 2). The product is ready for use when the battery indicator on the display (A) lights up green (Fig. 3).

Connecting the product to a 12 V battery

DANGER : Risk of explosion or fire!

• A spark may be visible when making the connection to a battery. Do not make this connection in the presence of flammable fumes.
• Do not use the vehicle battery in the proximity of open flames. Do not smoke when using a vehicle battery .

WARNING : Risk of electric shock!

• Take special care when working with a vehicle battery.
• Remove any jewelry (e.g. watch, bracelet and ring). Be careful not to short-circuit the battery with any metallic object

WARNING: Risk of chemical burns!
Wear eye protection and protective gloves! Vehicle batteries contain corrosive materials. Should battery acid come into contact with skin or eyes, flush it with water and consult a physician.

CAUTION: Risk of damage!

• The total loads of the connected devices must be under 750 W.
• Do not start the vehicle engine during operation.
• Always switch the product off and disconnect the ring connectors of the cables (J/K)

1. Unscrew the red terminal cap (F). Place the 22-65 ring connector of the red cable (J) on the red positive terminal(+) (E) (Fig. 4).
2. Tighten the red terminal cap (F) to clamp the cable connector securely (Fig. 4).
3. Unscrew the black terminal cap (H). Place the 22-65 ring connector of the black cable (K) on the black negative terminal (-) (Fig. 4).
4. Tighten the black terminal cap (H) to clamp the cable connector securely (Fig. 4).
5. Unscrew the nuts on the positive/+ battery post and negative/- battery post. Take the washers out (Fig. 5).
6. Connect the 22-8 ring connector of the red cable (J) to the positive/+ battery post (Fig. 8). Refit the washer and nut to secure the 22-8 ring connector. (Fig. 5).
7. Connect the 22-8 ring connector of the black cable (K) to the negative/- battery post (Fig. 8). Refit the washer and nut to secure the 22-8 ring connector.
8. The product is ready for use when the battery indicator on the display (A) lights up green (Fig. 6).

Switching on/off

NOTICE

• When using the product continuously inside a vehicle that is not running, the engine should be started at least once an hour for 10-15 minutes to keep the battery from discharging.
• The built-in fan (G) is activated when a significant amount of power increase the internal temperature and it exceeds its ambient operating temperature.
• If the product is unplugged directly when it is still on, the product emits a beep. Always switch the product off before unplugging it from the power source.
• When the product emits an audible alarm or the display (A) lights up red, refer to chapter Frequently Asked Questions for solutions.

Switching on

1. Press and hold the button (B) to switch the product on. The wattage indicator in all sections on the display (A) lights up blue, indicating 750 Wis available (Fig. 7).

2. Plug in the devices to be operated to either the outlets (C) or the USB port (D).
   NOTICE : The USB port (D) provides only 5 V ==/ 2.1 A power to an external USB­powered device. It does not support data communication.

3. Switch the devices on one at a time, so that the product does not have to deliver the surge currents required for all the loads at once.
   NOTICE : When operating motor appliances set the low power setting first, then increase gradually.

4. The status of the wattage indicators on the display (A) varies depending on the consumed wattage of the connected devices.

NOTICE

• When the wattage indicator lights up in the 100 W section, it indicates that the load should not exceed 100 W.
• When the wattage indicator lights up in the 100 Wand 250 W sections, it indicates that the load should not exceed 250 W.
• When the wattage indicator lights up in the 100 W, 250 Wand 500 W sections, it indicates that the load should not exceed 500 W.
• When the wattage indicator goes off, the maximum load has been reached.
• When the load exceeds 750 W, the wattage indicator goes off and the battery indicator lights up red.

Switching off

1. To switch the product off, press and hold the button (B) until the wattage indicator on the display (A) goes off.
2. Disconnect the cigarette lighter plug from the lighter plug or the cable terminals from the vehicle battery after use.

CAUTION Risk of electric shock or injury!
When disconnecting the cables, always start with the black cable (K) on the black negative teminal (-), then the red cable (J) on the red positive terminal(+). This is to avoid sparking.

NOTICE : When the product is switched on without any load connected, it still draws current from the power source. Always switch the product off after use to avoid discharging the battery.

Cigarette lighter plug fuse replacement
The cigarette lighter plug is equipped with a fuse rated 125 V, 8 A. Replace blown fuse with one of the same type.

1. Open the cap of the plug by loosening it in a anti-clockwise direction (Fig. 8).
2. Remove and replace the fuse with the same type (125 V, 8 A) (Fig. 8).
3. Close the cap in a clockwise direction.

Tips for maintaining battery condition

• Vehicle batteries are designed to provide brief periods of very high current needed  for engine starting. They are not intended for constant deep discharge.
• Regularly operating the product from a vehicle’s battery until the low-voltage alarm sounds will shorten the battery’s life. The battery operating time depends on:
  • the charge level of the battery,
  • the battery capacity,
  • the amount of power drawn by the devices that are connected to the product.
• With an average load of about 750 W connected to the product, it is needed to start the vehicle regularly, for example every hour or two, to recharge the vehicle’s battery.
• Prior to doing so, the product must be disconnected from the power source and must remain disconnected whilst charging is in progress.
• Consider connecting the product to a separate deep-discharge type of suitable battery if it is expected to run the electrical products for extended periods of time.

Automatic safety features

Cleaning and Maintenance

WARNING: Risk of electric shock!

• To prevent electric shock, unplug the product before cleaning.
• During cleaning do not immerse the electrical parts of the product in water or other liquids. Never hold the product under running water.

Cleaning

• To clean the product, wipe with a soft dry cloth.
• Make sure the fans and ventilation openings are free of dust or debris. Use a soft brush if needed.
• Never use corrosive detergents, wire brushes, abrasive scourers, metal or sharp utensils to clean the product.

Storage
Store the product in its original packaging in a dry area. Keep away from children and pets.

Maintenance
Any other servicing than mentioned in this manual should be performed by a professional repair center.

Frequently Asked Questions

Canada IC Notice

This Class B digital apparatus complies with Canadian CAN ICES-003(B) / NMB-003(B) standard.

Specifications

Feedback and Help
We would love to hear your feedback. To ensure we are providing the best customer experience possible, please consider writing a customer review.

Scan the QR Code below with your phone camera or QR reader:

If you need help with your Amazon Basics product, please use the website or number below.

amazon.com/gp/help/customer/contact-us
+1 877-485-0385

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>