Hbada E101 Ergonomic Office Chair Instruction Manual
- June 15, 2024
- Hbada
Table of Contents
Assembling instruction
HBADA 
NOTICEOF INSTALLATION
- Verfy the number ofall parts carefuly prior to installation
- Attention! The gas cylinder can be hardly removed once installed.To disassemble this chair when making a move, please beat the head ofthe cylinder using a hammer with rubber head and then remove the chassisikeep beating | the five-starseat lightly untilt fallsunder the action of vibration.Be careful when using tools.
Damages or accidents caused in instalation here are notwithin scope of
Wwarranty.please behavecarefully
NOTICEOF USE
- Please clean this chair by wiping it using softcloth,
- Please read Use’s Manual carefully priorto use,
- Do not use this chair in places with much humidity o fire; avoid direct sunlight for a long period.
- Do not step on this chair or use it as a ladder to avoid rollover.
- Attention: Only 1 user is allowed to sit on this chair to avoid instability and danger every time.
- Do not disassemble pneumatic bar for the sake of safety.
- Topreventfalls,make sure that the chair is evenly stressed during theuse of the chair.
- To avoid damage and safety, do not pull the chair quickly or hard.Do not sit on the armrest of the chair.
- If parts of the chair fall off and are lost or damaged, stop using immediately.
- Minors are prohibited from installing and regulating product functions alone. Minors are required to install and use chairs under adult supervision.
- The maximum load of 120KG.
- Non-professionals are prohibited from disassembling and repairing the parts of the chair.
E101BMC
E101BSD
Operation function
How to adjust the sitting height:
Make the chakr go up and down through the controller under the cushion
Operation method:
1f You wart o kower your chalr you neod fo sit on the cushion first and press
the first controller down on the right bottom of he cushion. Once the contoler
s oosened, seat wil iay ata proper height. Likewise, if you want to rise your
chair, you need to stay away from the cushion first and press the same
controller down,
How to adjust the backrest : “ Tum the hande to adfust and lock the back:
of the char. Operation method:
When you e siting on a chal and eaning back,and at the sarme time you pul up
the second loveron the chassis on e right hand side, the back of the chair can
be tilted back, and the angle can be fxed by puting cown the fever. I you it
to restore it, pull the same lever again when the back leaves e backrest.
Assembly parts list
Instructions for chair assembly
- As shown, Insert the cha legs into the central axis of the chalr legs and tighten them with screws.
- As shown,the castors can be inserted into the holes of chair legs separately.
- Buckle the decorative cap with the chair legs as shown in the figure, and then insert the gas cylinder.
- As shown,A screws are applied to fix the amrest on the cushion, each screw is screwed in half first, and then tightened one by one; (attention the both sides of armrests )
- As shown, insert the five claws into the hole of the chassis.
- As shown, connect the backrest steel plate to the backrest and fix it with 4 B screws.
- As the photo, insert the backrest into the tlt mechanism. People under 175¢m in height can use 4 B screws 1o fix the four holes on the upper part of the stesl plate to to the tiit mechanism.
- People over 175cm tall can use 4 B screws to fix the four holes located at the lower part of the steel plate to the tiit mechanism.
- As shown, decorative cover of the headrest is installed in the lower end of the headrest.
- As shown, insert the decorative cover of the backrest into the back of the chair and fix it with D screws.(use a Phillips screwdriver)
- As the photo, turn the chair upside down and rotate* it to an appropriate angle, then insert the back cover into the seat back slot, and then use a Phillips. screwdriver and D screws to fix it.
- Installation is complete.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>