Yunlink WB5AC Wireless Bridge Installation Guide

WB5AC Wireless Bridge Quick Installation Guide

Packing List

WB 5acL3,WB 5acL8,WB 5a-S,
WB Sac Base,WB 5ac-N,WB 5acDish,
WB SacDish Pro

|
---|---

Pole Installation

PoE Connection

Default Configuration

Defautt IP| Master: 192168.2.66/24
Slave: 192.168.2.67/24
---|---
Account| admin
Password| admin 01

product specifications

Fast Pairing

Master and Slave Bridge Configuration
Set one bridge to Master by switching the button to M, another bridge to Slave by switching the button to S.

Point to Point One—Key Pairing
Press Master bridge RST button for 1-3 seconds and release. In 1 minute, press Slave bridge RST button for 1-3 seconds and release. Two bridges will pair in 2 minutes.
Point to Muilti-Point Pairing
Press Master bridge RST button for 1-3 seconds and release. In 1 minute, press Slave bridge RST button for 1-3 seconds and release (repeat this operation to pair more Slave bridges ). Master and Slave bridges will pair in 2 minutes.
Remarks: Viren adding new Ste Snidge, current connection will disconnect.

Web Configuration

Computer Configuration by Cable Connection
Set computer local network IP address to 192.168.2.X (X range: 11-200), keep same network segment as the bridge.

Operation Guide

Step 1
Visit bridge default IP in browser to login page Step 2
Input account and password to login. Home page as following.

Step 3
Choose “Settings>System configuration>Advanced settings”, disable “Hardware switch”.

Master Bridge Setting
Step 4
Choose “Settings>Wireless configuration”. Set TX power, channel. Set Operation mode “Access point TDMA3” [Here are 4 modes: Access point (auto WDS)/ Access point (TDMA3)/Station (WDS/TDMA3)/Station (ARPNAT)]. Step 5
Click Network SSID name (For example: CPE), here will be popup page, finish all settings requested (SSID name, Security, password…), then “Done”.
Step 6
Click “Save changes” in the top right corner (figure 1-6). Confirm all settings, and save(figure 1-7).

Slave Bridge Setting
Repeat operation step 1~3, execute step 7.
Step 7
Choose “Settings>Wireless configuration”. Set Operation mode “Station (WDS /TDMA3”, set TX power (figure1—8). Click SSID name (for example, CPE), search SSID and here will be popup page (figure 1-9), select Master bridge SSID (Master). Step 8
Select Master bridge SSID (Master in figure 1-9), will switch to new page (figure 1-10), choose security method and Master SSID password.
Step 9
Click “Save changes” in the top right corner (figure 1-6). Confirm all settings, and save(figure 1-11, 1-12).

Step 10
As shown in Figure 1-13, the signal strength can be seen in the upper right corner, which establishes a connection between the master and slave bridges.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.
  Operations in the 5.15-5.35GHz band are restricted to indoor usage only.

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, Human proximity to the antenna shall not be less than 20cm (8 inches)during normal operation.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>