Vuture 31-RCSL1 Remote Control Searchlight with Battery Instruction Manual

Vuture 31-RCSL1 Remote Control Searchlight with Battery

Product Information

Specifications

• LED Light Output: 4800 lumen
• Color Temperature: Not specified
• Flash Function: Yes
• Rotation Range: Not specified
• Tilt Range: Not specified
• Waterproof Rating: IP65
• Size: 8 x 9 x 10 inches
• Weight: 7 lbs.
• Built-in Battery: 10000mAh, 11.1V Li-ion
• Battery Life: 3 hours (light only)
• RC Battery: 23A (2 included)
• RC Range: 170 feet (50 meters)

Mounting/Installation

For permanent vehicle mounting, follow these steps:

1. Separate the unit from the permanent base by pressing the release button and sliding the unit out.
2. Use the base as a pattern and drill holes corresponding to the indicated holes on the base.
3. Drill holes into a flat, rigid surface that is at least as large as the mounting base.

NOTE: Do not use any of the other holes in the base for permanent mounting to avoid breaking the base. The searchlight has a square base, so it can be slid into the mounting base in any orientation.

For temporary installation, separate the unit from the permanent mounting base. The bottom surface of the searchlight is magnetic and can be attached to any ferrous surface in any orientation.

NOTE: Make sure the surface is clean to reduce the likelihood of scratches. Do not slide the unit while magnetically mounted as it will cause scratches.

Product Usage

Charging

Before using the searchlight, make sure to charge the built-in battery.

1. Connect the wall charger to the wall charger port on the searchlight.
2. Connect the other end of the wall charger to a power outlet.
3. Leave the searchlight connected to the wall charger until fully charged. The charging time may vary.

Operation
The searchlight can be operated using the remote control or the buttons on the unit itself.

Movement Control Buttons
These buttons allow you to control the rotation and tilt of the searchlight. Use them to adjust the direction of the light beam.

Light On/Off Button
Press this button to turn the searchlight on or off. The light beam will illuminate or extinguish accordingly.

Light Emergency Flash Function
This function activates an emergency flashing mode for the searchlight. Press the corresponding button to activate or deactivate this mode.

Folding Handle
The searchlight features a folding handle for easy carrying and transportation. Fold or unfold the handle as needed.

Battery Compartment
The battery compartment holds the RC batteries (23A type). Open the compartment to replace or install new batteries when needed.

Position Switch
This switch allows you to select different modes or settings for the searchlight. Refer to the product manual for specific details on each position.

Scan QR Code
You can scan the provided QR code to access additional information and resources about the searchlight.

FAQ

Q: How long does the battery last?
A: The built-in battery has a life of approximately 3 hours when only the light is in use.

Q: Can the searchlight be permanently mounted on a vehicle?
A: Yes, the searchlight comes with a permanent base that can be used for vehicle mounting. Follow the instructions in the manual for proper installation.

Q: Can the searchlight be magnetically mounted?
A: Yes, the bottom surface of the searchlight is magnetic and can be attached to any ferrous surface temporarily. Ensure the surface is clean to avoid scratches.

Q: Can I control the searchlight remotely?
A: Yes, the searchlight comes with a remote control that allows you to control its movement, light on/off, and emergency flash function.

Q: What is the range of the remote control?
A: The remote control has a range of approximately 170 feet (50 meters).

Q: Is the searchlight waterproof?
A: Yes, the searchlight has an IP65 waterproof rating, making it suitable for outdoor use in various weather conditions.

OPERATION AND SAFETY MANUAL

RC SEARCHLIGHT
Designed to provide precision lighting for every occasion

Specifications

MOUNTING / INSTALLATION

For permanent vehicle mounting, use the permanent base.
Separate the unit from the base by pressing the release button and sliding the unit out. Use the base as a pattern, and drill holes corresponding to the indicated holes on the base. Drill holes into a flat, rigid surface that is at least as large as the mounting base.

NOTE: Do not use any of the other holes in the base for permanent mounting. The base might break.
The Searchlight has a square base, so it can be slid into the mounting base in any orientation.
For temporary installation separate the unit from the permanent mounting base.
The bottom surface of the Searchlight is magnetic and can be attached to any ferrous surface in any orientation.

NOTE: Make sure the surface is clean to reduce the likelihood of scratches. Do not slide the unit while magnetically mounted as it will cause scratches.

How to Use

1. Set the unit to the I – “Charging” or II – “Battery” position (see “Charging” section bellow.
2. Press the “ON/OFF” button on the remote control to turn the light on or off.
3. Press the movement control buttons to tilt and rotate the light head.
4. Press the “Flash” button to activate the emergency flash function.

Charging

1. For wall charging, plug the unit to a standard wall outlet using the wall charger. Leave switch in the 0 position. The unit is inoperable in this state.
2. For vehicle charging, plug the unit to a standard vehicle cigarette lighter port using the vehicle charger. Set the switch to the I – “Charging” position. The unit is fully operable in this state. If the unit is operated in this state, the battery charging rate will be slower.
   For battery use set the switch to the II – “Battery” position.

Discarded electrical products must not be disposed of together with household waste. Please use recycling facilities at your local authority for advice on recycling. The battery must be removed from the device before it is broken up. The device must be disconnected from the mains when the battery is removed. Please dispose of the battery safely.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. (Example – use only shielded interface cables when connecting to computer or peripheral devices).

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation

References

• Lineman Tools | Jameson Tools | Wiring Equipment Arborist Tools

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>