Sankey F818 Remote Control Instructions
- June 15, 2024
- SANKEY
Table of Contents
Sankey F818 Remote Control
Product Information
Specifications
- Compliance: Part 15 of the FCC rules
- Interference: Must not cause harmful interference; must accept any interference received
- Class: Class B digital device
- RF Energy: Generates and can radiate radio frequency energy
- Installation: Should be installed and used in accordance with the instructions
- Protection: Provides reasonable protection against harmful interference in a residential installation
- Radiation Exposure: Meets general RF exposure requirement; can be used in portable exposure condition without restriction
Product Usage Instructions
FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
FAQ
Q: What should I do if this equipment causes harmful interference to my radio or television reception?
A: If you experience harmful interference, try the following measures:
- Reorient or relocate your receiving antenna.
- Increase the separation between this equipment and your receiver.
- Connect this equipment into an outlet on a different circuit from your receiver.
- If the issue persists, consult the dealer or an experienced radio/TV technician for further assistance.
FUNCTION INSTRUCTION OF EMITTER
-
Led Indicator
-
Speed Control
-
FanOff
-
Fan Reverse/Forward
Press this Key when the fan works -
Warm light(Yellow light)
-
Mixing light
-
Whitelight
-
Light On/Off
-
Brightness control switch
-
Timer
Once pressing the timer key, please do not press any other keys. Or the order will be cancelled (WIFI) -
Silent mode switch
Press and hold the button for 2 seconds to cancel the ‘Beep’ sound
KINDLY REMINDERS
- Learning code matching mode is used between emitter and receiver. Turn “ON’ the supply power within 30 seconds and press the emitter’s· OFF’ button for 5 seconds, it can load normally after hearing a long sound “bee’, which means learning successfully and it can work normally. (PS: Learning mode is not accepted after turn “ON” the supply power for 30 seconds.)
- When the emitter can not control the receiver, please check the battery switch touching normally or not, correction of the positive and negative, full or empty of the power.
- When the emitter cannot control the receiver. please check is there any existence of similar remote-controlled products nearby,then check whether they work, because a remote-controlled product with the same frequency will disturb each other.
- Low voltage of battery will affect the sensitivity of the emitter and the signal reception accordingly(the indicated light will flash out its warning when the battery get low voltage),must be replaced if the battery is getting low voltage.
- Please take out the battery from the emitter when leaving unused for long time.
- The maximum load of lighting see the above “POWER PARAMETER LIST’ PS: Please connect the ground wire correctly, otherwise it may cause the light micro-light or flash.
- When instaliing the fan,the fan ceiling cover don’t press the antenna(or other wire),it is easy to break down the wire and short-circuit.
FCC
FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any inte rference received,
including interference that may cause undesired operation. Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interferenceto radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.