FARO SpA 540050 Remote Control for Room Lamps User Manual
- June 15, 2024
- FARO SpA
Table of Contents
FARO SpA 540050 Remote Control for Room Lamps
Product Information
Specifications:
- Remote control battery: LR-23A/12V
- Transmitter frequency: 315 MHz
- FCC ID: 2BC9L-540050
Product Usage Instructions
Remote Control Functions Buttons:
The remote control has the following functions:
- On/Off: Switches on or turns off the lamp. When switching on, the last selected scenario will be recalled.
- Scenario 1: Sets the 1st level of illumination, maximum + upper LEDs (minimum brightness).
- Scenario 2: Sets the 2nd level of illumination, maximum + upper LEDs.
- Scenario 3: Sets the 3rd level of illumination, maximum + upper LEDs.
- Scenario 4: Sets the 4th level of illumination, maximum + upper LEDs.
- Scenario 5: Sets the 5th level of illumination, maximum + upper LEDs (maximum brightness).
- Adjustment to lower LEDs: Allows variation in intensity from 0% to 100%. The intensity increases or reduces depending on the time the button is pressed by the user.
- Programming button: Allows access to overwrite and reset functions.
Overwriting Scenario:
To modify the level of illumination over an existing scenario, follow these steps:
- Set the desired level of illumination.
- Press the two indicated buttons at the same time for 3 seconds: the button corresponding to the scenario to be modified and the programming button. The green LED will flash.
- Release the buttons as soon as the blue light becomes steady.
Note : This modification is possible for all 5 scenarios.
Restore Initial Settings:
To erase all settings and restore the initial settings, follow these steps:
- Prolonged press the two buttons for approximately 5 seconds until the green light flashes.
- Release the buttons as soon as the green light becomes steady.
Modify the Coding of the Remote Control:
To create a new code for communication between the remote control and the lamp, follow these steps:
- This function should only be used when pairing a new remote control in place of the current one.
- Remove power to the lamp.
- Restore power and within 60 seconds, proceed with points 3 and 4.
- Prolonged press the two buttons for approximately 5 seconds until the green light flashes.
- Release the buttons as soon as the green light becomes steady.
FAQ (Frequently Asked Questions)
-
Q: How do I replace the remote-control battery?
A: The battery can be accessed through a hatch at the back of the remote control. Exchange it for one with the same characteristics, observing the indicated polarity: MOD: LR-23A/12V. -
Q: What are the technical specifications of the remote control?
A: The remote control battery is LR-23A/12V, and the transmitter frequency is 315 MHz. The FCC ID is 2BC9L-540050. -
Q: Is the device compliant with FCC rules?
A: Yes, the device complies with part 15 of the FCC Rules. It does not cause harmful interference and accepts any interference received. -
Q: Can I make changes or modifications to the equipment?
A: No, changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Intended Use
The Remote Control is supplied as an accessory of the General Light Siderea for its control.
The remote control allows to:
- switch on and off
- dimmering
- set up lighting scenarios according tho the specifications described in §2.
Remote Control Functions
| Buttons | Functions |
|---|---|
| On/Off: switching on/turning off the lamp. On switching on, the last | |
| scenario selected will be recalled |
maximum + upper LEDs
| Programming button; allows access to “overwrite” and “Reset” functions.| |
Scenario 4: 4th level of illumination, maximum + upper LEDs
| Scenario 1: 1st level of illumination, maximum + upper LEDs (min.)| |
Scenario 5: 5th level of illumination, maximum + upper LEDs (max.)
| Scenario 2: 2nd level of illumination, maximum + upper LEDs| | Adjustment to
lower LEDs; variation in intensity of 0% to 100%.
An increase/reduction in intensity depends on the time for which the button
is pressed by the user.
| Company Logo, no function
| Overwriting scenario: Modification of the level of illumination over an existing scenario.
Procedure:
1. Set the desired level of illumination.
2. Press the two indicated buttons at the same time for 3 secs.; that of the scenario to be modified and the programming button, the green LED flashes
3. Release the buttons as soon as the blue light is steady. Note: The Modification is possible on all 5 scenarios
| Restore initial settings (erases all settings) Procedure:
1. Prolonged pressing of the two buttons for some 5 secs., the green light flashes.
2. Release the buttons as soon as the green light is steady.
| Modify the coding of the remote control; create a new code for communicating between the remote control and the lamp.
1. This function must be only be used in the event that it is necessary to pair a new remote control in the place of the one in use.
Procedure:
1. Remove power to the lamp.
2. Restore power and within 60 seconds, proceed with points 3 and 4
3. Prolonged pressing of the two buttons for some 5 secs., the green light flashes.
4. Release the buttons as soon as the green light is steady.
5. When the green Sidèrea LED flashes rapidly, press the programming button
Replacement Of The Remote-Control Battery
The battery is accessed through a hatch at the back of the remote control. Exchange it for one with the same characteristics, observing the indicated polarity:
- MOD: LR-23A/12V
Technical Specifications
- Remote control battery: LR-23A/12V
Transmitter frequency: 315 MHz
FCC
FCC ID : 2BC9L-540050
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.