Zhuhai Jinhong Technology AW0506 AH WiFi Extender Set User Manual
- June 13, 2024
- Zhuhai Jinhong Technology
Table of Contents
AH WiFi Extender
User manual
AW0506 AH WiFi Extender Set
- A. There are two modules for the AH WiFi Extender Set, One is called“AH Transmitter”(with network port) , another is called “AH Extender”
- B. Connect AH Transmitter to the router (through LAN port) and connect it to the USB Power Adapter with the network cable. Once the AH Transmitter is power on, the POW light and RX/TX light will flash for self checking, After the self check is completed, the POW light and RX/TX light will remain on continuously
- C. Put the AH Extender in a place where it needs to be connected to the Internet, Power on it when it was connected to the Power adapter with USB cable, and POW light and SYNC light will be on (if the SYNC light is not on, please adjust the position of AH Extender), in the same time SYNC light of the AH Transmitter will be on, indicating that the connection between the AH Transmitter and AH Extender has been established successfully.
- D. Find the router(SSID) that named “AH-WiFi**” in your router listing, using the default password “12345678”, then you can go online whether it’s a phone, tablet, or WiFi 2.4g enabled computer. At the same time the LINK light of the A Extender is always on.
Step 1 ：Search SSID
named “AH-WiFi***” in WLAN settings of your phone （Figure 1 ）
Step 2** ：Enter the password: “12345678”, click on Connect, at the same
time the LINK light is on, and then you can go online （Figure 2 ） 
Step 3 ：If you need to modify the default SSID name and password, please
follow the following steps: Click on “Modify Network” to start modifying the
parameters first （Figure 3 ）
Step 4 ： Change the way the phone obtains IP from DHCP to static mode and
use the static IP address 192.168.123.200; set th Router as 192.168.123.1;set
the Subnet Mask as 255.255.255.0;set the DNS Server as 192.168.123.1, and then
click Save （ Figure 4 ）
Step 5 ：Enter the address “192.168.123.1” in the web browser from your
mobile phone, then you will enter into the management web page, You can view
all pages by pressing the menu button in the upper left corner of the
interface
If you couldn‘t access the management web page, Please check if the phone is
connected to the AH Extender(Only the LINK light of the AH Extender is on that
indicate the phone is connected successfully) （Figure 5 ） 
Step 6 ：The wireless settings page allows you to set and modify the WiFi
SSID name, encryption method, and password. Click the save button to apply the
settings, click the restore button to clear the content filled in on the
webpage. After the modification is completed, the IP will be statically
changed back to DHCP, so that you can access the internet normally （Figure 6
）
FCC Statement
-
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. -
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
To comply with RF exposure requirements, a minimum separation distance of 20cm
must be maintained between the user’s body and
the product, including the antenna. 
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>