Flysocks PF260 Golf Rangefinder with Slope User Manual

Flysocks PF260 Golf Rangefinder with Slope

SAFETY INSTRUCTIONS

Warning

• Do not store into the loser beam, it may damage your eyes.
• Do not aim the device at the sun directly, doing so may permanently damage the internal components and your eyes.
• The storage temperature of the device is -10 – 60°C / 14 – 140°F. Operating outside this range may damage the device.

Environment Protection

• This product contains a built-in 1000 mAh lithium battery. Do not dispose of it with household waste per local regulations.

Notice

• To protect the lens coating, do not touch the lens with your fingers.
• This loser rangefinder hos been precisely calibrated. Do not disassemble, or you may void the warranty.
• Cleon the lens with the included microfiber cloth to ovoid damage. Do not use rough cloths.
•  Avoid impact and heavy loads when carrying or using this device.
• Keep the device away from extreme heat or corrosive materials.
• Please keep it in a dry. cool, and well-ventilated place to ovoid moisture, direct sunlight, dust, and temperature mutation.
• Fog con interfere with the loser ray-path, reducing measurement accuracy.
• This device hos on IP54 weatherproof rotting. Do not expose it to heavy rain or submerge in water.

PACKAGE CONTENT

PRODUCT INTRODUCTION

1. Eyepiece Knob
   Rotate to adjust focus.

2. Eyepiece

3. Status LED

4. Red light means in charging mode, green light means it is fully charged.

5. Power Button
   Short press to measure, long press to lock the flog.

6. Mode Button
   Short press to switch mode, long press to switch the unit (M / Yd).
   Slope Switch
   Switch to enoble/disoble the slope compensation function.

7. Laser Emitter Lens

8. Laser Receive Lens

9. Magnetic Stripe

10. USB-C Charging Port

11. Lanyard Hole

PRODUCT INTRODUCTION

1. Low Battery Indicator
2. Measured Distance (Linear Distance)/ Units
3. Flag Lock Icon
4. Measuring Reminder
5. Slope Icon/ Height Icon/ Reading/ Units
6. Angle Icon/ Reading/ Angle Unit/ Speed Unit
7. Two-Points Height Icon
8. Crosshairs

HOW TO USE

ON / OFF
Short press Power Button to power ON. Automatically power OFF after 30s of inactivity.

Distance Measurement
Please adjust the eyepiece to focus on the target before measuring. In the course of the measurement, if the target reflection is weak or beyond the measuring range, it will display as “—“, The measurement range is affected by the materials of the target, the inclined angle of the target surface, the visibility of the weather, etc. In general, if the target surface is smooth and bright with a larger area, the beam is perpendicular to the target surface and the weather is cloudy without fog, the measurement range will

(with Flagpole Lock Function)
Short press Mode Button to enter Golf Slope Mode. Aiming at Target B and short press Power Button, the screen will display Linear Distance, Ballistic Distance, and Angle a. Long press Power Button to activate the Flagpole Lock Function. Aiming at Target B and sweeping back and forth, the will flash, when the flagpole is locked, the device will vibrate, and the screen will display Linear Distance, Ballistic Distance and Angle a. (Sweeps are more likely to trigger a lock when there is a background behind the flagpole.)

Two-Point Height Mode

• Short press Mode Button to enter Two-Point Height Mode.
• Aiming at Target B, and pressing Power Button to get the Linear Distance AB and Angle a, then aiming at Target C, and pressing Power Button to get the Linear Distance AC and Angle (3, the screen will display Height H and Angle 8(a-(3}.

Auto Height Mode

• Short press Mode Button to enter Auto Height Mode.
• Aiming at Target B, and pressing Power Button, the screen will display Linear Distance AB, Height H and Angle a.

Horizontal Mode

• Short press Mode Button to enter Horizontal Mode.
• Aiming at Target B. and pressing Power Button, the screen will display Distance Land Angle a.

Speed Mode

• Short press Mode Button to enter Speed Mode to activate the speed.
• Aiming at Target B and moving slightly, the speed of B can be measured accordingly.

• Speed measurement range: 18-300 km/h.
• Angela must be less than 10°, the smaller the angle, the higher the accuracy.

SPECIFICATIONS

FCC COMPLIANCE INFORMATION STATEMENT

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. operation is subject to the following two conditions

1. this device may not cause harmful interference. and
2.  this device must accept any interference received. including interference that may cause undesired operation.

• Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
• This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However. there is no guarantee that interference will not occur in a particular installation.
• If this equipment does cause harmful interference to radio or television reception. which can be determined by turning the equipment off and on. the user is encouraged to try to correct the interference by one or more of the following measures
• Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be ca-located or operating in conjunction with any other antenna or transmitter.

CANADIAN COMPLIANCE STATEMENT

This device contains license exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licenceexempt RSS(s). Operation is subject to the following two conditions

1.  This device may not cause interference.
2.  This device must accept any interference, including interference that may cause

• Manufacturer

• Shenzhen Mileseey Technology Co .. ltd.

• Address

• No.3601 Block A, Tanglang Town Plaza West, Fudging Community, Taoyuan Street, Nanshan District, Shenzhen, China

• Supervisor

• MountTech HK Limited

• Address

• 19H Maxgrand Plaza No.3 Tai You Street San Po Kong, KL, Hong Kong
  Made in China
  CAUTION : CLASS 1 LASER PRODUCT CONSUMER LASER PRODUCT

• IEC 60825-1:2014 EN50689:2021 WAVELENGTH 905nm

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>