TARAMP S HV 40.000 Chipeo Class D 1 Channel 20000 watts Instruction Manual

**TARAMP S HV 40.000 Chapeau Class D 1 Channel 20000 watts Instruction Manual

**

.Installation Procedure

1. Follow all procedures described below;

2. If you do not follow the proper procedures by qualified professionals, Tramps’ is exampled of any responsibility;

3. Insulate completely all system connections, this avoiding electrical contact with the vehicle chasse;

4. Accessories and peripherals (such as Head Units, equalizers, crossover or other equipment requiring power at 12 volts) should be eliminated from the original vehicle connections. The equipment will be supplied by the of auxiliary batteries bank, designed according to system needings;

5. Circuit breakers must be installed in a visible and easily access place for operating, and
   system maintenance;

6. The batteries must be insulated once installed, to avoid electric shock, sparks and/or damage to vehicle;

7. All connections should be made with all circuit breakers off.

TURNING ONTHE AMPLIFIER

1. Check that any system is not shorted or in contact with the chassis of the vehicle;
2. Check carefully if the negative points of high voltage batteries bank and 12.6 VDC battery negative point are connected together;
3. Connect the speakers in its output;
4. Make sure that your batteries are properly charged;
5. Keep the volume control (Level) at the minimum;
6. urn on the remote to activate the preamp;
7. After checking the preamplifier, disconnect the remote, activate the circuit breakers and turn-on the remote again;
8. Set all volume settings, frequency cuts and enjoy all the advantages of your new amplifier.

CARING OF YOUR SOUND SYSTEM

1. After the use of the sound system, turn off all circuit breakers;
2. Never move the vehicle with activated circuit breakers;
3. Do not connect the battery charger with the sound system in operation;
4. Do not add any other battery charger; Use only the specified charger.
5. Do not start the vehicle engine with the sound system in operation;
6. The engine starting (ignition) is only allowed once all circuit breakers are turned off.

NOTE :
Failure to comply with any of the above procedures fully exempts Tramps’ from any liability for the risks of its use. So for you can take advantage of this high technology, high quality and powerful amplifier, be sure to follow step by step all safety procedures, otherwise it could implies the loss of warranty.
For further information please contact our Technical Department to solve all doubts.
All electrical and electronic equipment installation must be made by qualified and trained professionals.
Your life is valuable. Avoid accidents. Depending on the severity of an electric shock, it can coctuourlifa”

Functions & input

1. INPUT UNBAL : Connect to the RCA output of the Head Unit using good quality shielded cables to avoid noise pickup. The signals from the Land R inputs are mixed (added) internally
2. THRU OUT : This output (L and R) can send the same input signal (INPUT) to another amplifier.
3. LEVEL : Adjust the sensitivity of the amplifier input, in order to get better performance and volume.
4. 12.6 VDC POSITIVE TERMINAL (1.5A) : Use an exclusive 12.6V battery and relay (driven by the remote signal from Head Unit. See diagram at the page 06).
5. FANS : HV 40.000 has four internal ventilation coolers, which can not be blocked. For perfect operation, the amplifier must be installed in a cool and dry place. We recommend not embedding it, so that air can circulate throughout the inside of the product, thus preventing the thermal shutdown.

LEDS indicators / protections

GREEN LED (HV): Indicates high voltage presence at the power terminals.
BLUE LED (ON): Indicates powered amplifier.
YELLOW LED (CLIPPING): Indicator of clipping and protections. (See protections below).
RED LED (PROTECTION): Indicator of protections. (See protections below).

SHORT : Red LED on.
LOW VOLTAGE (HV) : Blue LED alternating with yellow.
HIGH VOLTAGE (HV) : Blue LED alternating with red.
MISSING (HV) : Blue LED blinking.
TEMPERATURE: Flashing yellow LED.

Voltage 12V

LOW VOLTAGE 12V: If the voltage is less than 9VDC, red LED flashes 2x. HIGH VOLTAGE 12V: If the voltage exceeds 16VDC , red LED flashes 3x.

Functions outputs & power input

1. SPEAKER +: Output connector positive for loud speakers.
2. POWER +: Positive power input for high voltage.
3. POWER -: Negative power input for high voltage.
4. SPEAKER -Output connector negative for loud speakers.
5. FANS : HV 40,000 has four internal ventilation fans, which can not be blocked. For perfect operation, the amplifier must be installed in a cool and dry place. We recommend not embedding it, so that air can circulate throughout the inside of the product, thus preventing the thermal shutdown.

Please note: This is a device that will be high voltage powered. As in any electronic equipment take care to not cause any incident during installation. We recommend using of well insulated tools.

Cables and circuit breakers should be good quality with its connections well protected and insulated following the specified gauge.
Wrongly dimensioned wiring may degrade the amplifier performance and causes power loss, wiring heating and serious risk of fire.
The wiring gauge recommended described in scheme on page 06.

Interconnections

Installing one or more batteries is necessary to work at 12.6 Volts, to supply the pre amplifier and other equipment that require this same voltage as Head Unit, crossover, equalizers, amplifiers, etc. As shown in the scheme.

Gauge for the output cable is 21mm², calculated a maximum length of 2m.

****Attention! Do not use the vehicle chassis as system grounding point. Is forbidden the locomotion of the vehicle with this in sound system in operation. For maximum power and amplifier performance, use 18 x 130 amps batteries at least. 0

Charging the battery bank

****IT IS MANDATORY INSTALLATION OF CIRCUIT BREAKERS (DC)
In order for the battery bank in series. Are fully charged, we recommend that you use individual sources for each battery. As an example in the images we indicate the source of 15A Tramps’. It is expressly mandatory to use a 15A fuse in the positive output of each battery.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>