RETLLAS SMS-00-SA Personal Home Safe Fireproof Waterproof User Manual
- June 15, 2024
- RETLLAS
Table of Contents
RETLLAS SMS-00-SA Personal Home Safe Fireproof Waterproof
Product Information
The product is a safe with the following components:
- Bolts
- Reset button
- Battery compartment
- Knob
- Emergency lock cover
- Yellow light
- Red light
- Green light
- Confirm button
Please note that the position of the components on the actual product may be slightly different from the pictures above, but the method of operation is the same.
MOUNTING METHOD
- Fix the safe in the place which is not easy to move.
- Drill holes for expansion bolts (or clamping screws) in the right place.
- Turn the expansion bolts anticlockwise to separate.
- Use the expansion bolts (or clamping screws) to secure the case to the wall.
- Make sure the case is mounted in place as required and then tighten all screws.
CAUTION
Use the expansion bolts when there is the concrete wall surface. Use the
clamoing screws when there is the wooden wall surface.
INTELLIGENT ELECTRONIC SAFE
- Please do not keep emergency keys in your safe!
Dear valued customer
Thank you for choosing our products!
- You’ve taken an important step in organizing and protecting your most valued possessions. Every series of our safes is professionally made and designed to provide safety.
- Please take time to read and familiarize yourself with the proper operating procedures of your new safe presented on the following pages.
Schematic drawing of case
Schematic drawing of control panel
- Bolts
- Reset button
- Battery compartment
- Knob
- Emergency lock cover
- Yellow light
- Red light
- Green light
- Confirm button
CAUTION :The position of the components on the actual product may be slightly different from the pictures above, but the method of operation is the same.
OPENING YOUR SAFE FOR THE FIRST TIME
When opening the safe for the first time, you should use the emergency key to open it. When you have forgotten the codes, you can also use the emergency key to open the safe.
- Remove emergency lock cover.
- Insert the emergency key, and turn it anticlockwise.
- Turn the knob clockwise to open the door.
CAUTION : Finish operation, pull out the emergency key and keep it in a safe place.
INSERTING THE BATTERIES
- Open the door.
- Insert 4 × AA batteries into the battery compartment.
- Normally, if the red light is on, it means the voltage is low and you should insert new batteries.
- CAUTION : Replace 4 new batteries in the direction indicated by the “+” and “-” symbols. When the power outage lasts more than thirty minutes, you should reset the user code.
OPENING THE DOOR WITH THE CODE
- Input your user code(3 to 8 digits) or master code(3 to 8 digits), each pressing results
CAUTION : The user preset code “159”. If the code is entered incorrectly, the buzzer will sound 3 times and the yellow light will flash 3 times. You need to enter your code again.
CLOSING THE DOOR
- Turn the knob anticlockwise to close the door.
SETTING THE USER CODE
- With the door open, press the reset button. The yellow light will flash twice and the buzzer will beep twice.
- Input the new user code(3 to 8 digits), and press “#” to confirm. The buzzer will beep twice and the yellow light will flash twice. It means the setting is successful. I
- CAUTION : The preset code “159”. Before closing the safe, enter the new code and make sure the safe can be opened.
SETTING THE MASTER CODE
- it the now master out 00 digress, and Preston to confirm. The buzzer will beep twice and the yellow light will flash twice. It means the setting is successful.
ALARM FUNCTION
- If the wrong code is entered 3 times continuously, the keyboard will be locked for 20 seconds and the buzzer will sound for 20 seconds.
- If the wrong code is entered 6 times continuously, the keyboard will be locked for 5 minutes and the buzzer will sound for 5 minutes. “
CAUTION : The keyboard would be disabled during the beeping. You can only stop the beeps by opening the safe with emergency key and power-cut by removing the battery.
MUTE FUNCTION
- Press ” *633″ to turn off the sound.
- Press ” *66 ” to turn on the sound.