aVIGILON ES-HD-HWS-SM CCTV Housing Camera User Guide

: June 15, 2024
: aVIGILON

Table of Contents

aVIGILON ES-HD-HWS-SM CCTV Housing Camera
Specifications
Product Description
Installation
How to install the camera
Cabling
Closing the housing
Technical Data
Cleaning
FAQ’s
Read User Manual Online (PDF format)
Download This Manual (PDF format)

aVIGILON ES-HD-HWS-SM CCTV Housing Camera

Specifications

Model: ES-HD-HWS-SM
Designed for small spaces
Side opening system for easy access to the camera and lens

Product Description
The Avigilon High Definition Camera Housing (ES-HD-HWS-SM) is designed to optimally fit into small spaces. It features a side opening system that allows easy access to the camera and lens.

Safety Rules
Please follow these safety rules to ensure proper usage of the product:

Read and understand the user manual before installing or using the product.
Loosen the 2 screws on the side of the housing to open it.
The manufacturer declines all responsibility for any damage caused by improper use of the product.
Follow national standards and regulations when installing and using the product.

Product Description

The ES-HD-HWS-SM has been designed to optimally fit into small spaces. The side opening system allows easy access to the camera and lens.

Safety rules
The manufacturer declines all responsibility for any damage caused by an improper use of the appliances mentioned in this manual. Furthermore, the manufacturer riserve the right to modify its contentswithout any prior notice.

The device must be installed only and exclusively by qualified technical personnel.
Before any technical work on the appliance, disconnect the power supply.
Do not use power supply cables that seem worn or old.
Never, under any circumstances, make any changes or connections that are not shown in this handbook: improper use of the appliance can cause serious hazards, risking the safety of personnel and of the installation.
Use only original spare parts. Not original spare parts could cause fire, electrical discharge or other hazards.
This device was designed to be permanently installed on a building or on a suitable structure.
When installing the device, comply with all the national standards.
The electrical system of the building on which the device is to be installed must have a two-pole protection circuit (circuit breaker) complete with an automatic two-pole switch which provides protection for earth fault current (circuit breaker + differential) with a minimum distance between contacts of 3mm.
Any device which could be installed inside the housing must comply with the current standards.

Installation

How to install the camera

To open the housing, loosen the 2 screws on the side (01).
Fasten the camera ith the 1/4” screw (01) to the camera support (02) and, if necessary, place the insulating spacer between the camera and support (03).
Fasten the camera support using the 2 screws.

Brackets for internal cable channel

Fix the cable glands in the direction shown (01), taking care to tighten the nuts properly (02).
Pass the wires and the cables through the bracket into the housing; these cables should be locked by the cable glands (01).
Secure the housing to the bracket using the 4 screws provided with the bracket. Add some thread locker glue on the screw (as LOCTITE 243). The cable glands are suitable for cables with a diameter comprised between 5 and 10mm.

Cabling

Make sure your external power source matches the camera’s power requirements

Camera board (if present)

Connect the camera power cable to the connector marked OUT (01) on the board following the pictograms.
Connect the external power cable to the connector marked IN (02) on the board.
Connect the power cable as shown.

Make sure the earth conductor is at least 10mm longer than the others. The power supply cable conductors must be tied up next to the terminal.

Closing the housing

Take the desiccant salt bag out of its transparent pack and insert it into the housing.
Then close the housing using the screws (01) as soon as possible to maintain the desiccant capability of the salt bag.

Technical Data

Mechanical

2xM16 cable glands
Glass window (WxH): 60/95x63mm (2.4/3.7×2.5in)
Internal usable area (WxH): 70x70mm (2.7×2.7in)
Internal usable length with and without accessories: 250mm (9.8in)

Electrical
(if the board cabling is present)

Heater Ton 15°C±3°C (59°F ±5.4°F) Toff 22°C±3°C (71.6°F ±5.4°F)
IN 12-24 Vdc, 3Amax
IN 12-24Vac, 50/60Hz 3Amax

Environment

Indoor / Outdoor
Operating temperature with heater: -20°C / +60°C (-4°F / +140°F)

Certifications

CE EN61000-6-3, EN60950-1, EN50130-4
IP66/IP67 EN60529

Cleaning

Window and plastic cover cleaning (PC)
We suggest using neutral soap diluted with water or specific products for lens cleaning applied with a soft cloth.

CAUTION : Avoid ethyl alcohol, solvents, hydrogenated hydrocarbide, strong acid and alkali. Such products may irreparably damage the surface.

Disposal of waste materials
This symbol mark and recycle system are applied only to EU countries and not applied to the countries in the other area of the world.

© 2014 — 2014 Avigilon Corporation. All rights reserved. Unless expressly granted in writing, no license is granted with respect to any copyright, industrial design, trademark, patent or other intellectual property rights of Avigilon Corporation or its licensors.

AVIGILON, CAPTURE IT WITH CLARITY, HDSM, HIGH DEFINITION STREAM MANAGEMENT (HDSM), THE BEST EVIDENCE and LIGHTCATCHER are unregistered and/or registered trademarks of Avigilon Corporation in Canada and other jurisdictions worldwide. Other product names mentioned herein may be the unregistered and/or registered trademarks of their respective owners. ™ and ® are not used in association with each trademark in this document.