KICKER BTCAN65 6.5 Inch Bluetooth Powered Speaker Owner’s Manual

KICKER BTCAN65 6.5 Inch Bluetooth Powered Speaker

Specifications

• Model: KICKER BTCAN65
• Power Output: 102, A-weighted, re: rated power @ 14.4V
• Tweeter Dome Material: Neodymium
• Tweeter Design: Dome
• Woofer Cone Material: Polypropolene
• Woofer Surround Material: Santoprene
• Aux Input Line Output: Stereo 3.5mm Female Buffered, 1V

Installation

Power & Auxiliary Wiring
To avoid electrical short, disconnect the vehicle’s battery before starting the installation.

1. Run the black ground wire to a solid, metal area of the vehicle’s chassis or the negative battery terminal. Crimp the provided 5/16 ring terminal to the ground wire and securely connect it to the grounding point.
2. Run the yellow +12V constant wire to the battery location. Crimp the provided 15A ATC fuse to the yellow wire using a heat-shrink butt connector. Apply heat to create a secure and insulated connection. Connect the fuse’s 5/16 ring terminal to the positive battery terminal. Ensure that the fuse is kept within 18 inches of the battery at all times.
3. Connect the Red +12V Ignition Wire to the switched ignition power source, dash-mounted switch, accessory, or relay switch.

LED Grille Wiring

1. Connect the female LED plug of the Right BTCAN, located on the smaller, secondary wire loom, to the male LED plug of the Left BTCAN.
2. To control LED Grille behavior, install the KICKER KMLC (sold separately) by connecting the male LED plug of the Right BTCAN, located on the larger, primary wire loom, to the KMLC female plug.

Operation

Multi-Function Button
The Multi-Function Button on the BTCAN is used for various operations:

• Power On/Off : Press and hold the Multi-Function Button for 3 seconds to turn the speaker on or off.
• Play/Pause: Press the Multi-Function Button once to play or pause audio playback.
• Answer/End Call: Press the Multi-Function Button once to answer an incoming call or end an ongoing call.
• Reject Call: Press and hold the Multi-Function Button for 2 seconds to reject an incoming call.

Status LED
The Status LED indicates the current status of the BTCAN. It has the following behaviors:

• Solid Blue: Bluetooth mode
• Blinking Blue: Pairing mode
• Solid Red: Charging mode
• Solid Green: Fully charged

Setting Input Source
The BTCAN supports multiple input sources. To change the input source:

1. Press and hold the Multi-Function Button for 5 seconds until you hear a voice prompt saying “Input Mode”.
2. Short press the Multi-Function Button to cycle through the available input sources: Bluetooth, AUX IN, and Line Output.
3. When the desired input source is selected, wait for a voice prompt confirming the selection.

Line Output & AUX IN
The BTCAN has a Line Output and an AUX IN for connecting external devices. Here’s how to use them:

• Line Output: Connect a compatible audio device to the LINE OUT port using a 3.5mm audio cable. Adjust the volume of the audio device and the BTCAN accordingly.
• AUX IN : Connect an audio source to the AUX IN port using a 3.5mm audio cable. Adjust the volume of the audio source and the BTCAN accordingly.

Remote Control Install
To install the wired remote control:

1. Choose a suitable location on the dashboard or a standard marine panel to mount the remote control.
2. Securely mount the remote control using the provided screws or adhesive tape.
3. Connect the remote control cable to the BTCAN’s remote control port.

Remote Control Operation
The wired remote control allows you to control various functions of the BTCAN without directly accessing the speaker. Use the following buttons on the remote control:

• Power On/Off : Press the power button to turn the BTCAN on or off.
• Volume Up/Down: Use the volume buttons to increase or decrease the speaker’s volume.
• Play/Pause: Press the play/pause button to play or pause audio playback.
• Next/Previous Track: Use the track buttons to skip to the next or previous track during audio playback.

Troubleshooting

If you encounter any issues with the BTCAN, refer to the following troubleshooting steps:

• Make sure the speaker is properly connected to the power source and the audio source.
• Check the battery level of the speaker. If it’s low, charge the speaker using the provided charging cable.
• Reset the speaker by pressing and holding the Multi-Function Button for 10 seconds until you hear a voice prompt saying “Reset”.
• If the LED Grille is not functioning properly, check the wiring connections and ensure the KICKER KMLC (if installed) is properly connected.

FAQ

• Can I use the BTCAN with my mobile device?
  Yes, the BTCAN supports Bluetooth connectivity and can be paired with your mobile device for wireless audio streaming.

• Can I control the LED Grille behavior without the KICKER KMLC?
  No, to control the LED Grille behavior, you need to install the KICKER KMLC and connect it to the BTCAN.

• How do I reset the BTCAN?
  To reset the BTCAN, press and hold the Multi-Function Button for 10 seconds until you hear a voice prompt saying “Reset”.

Overview

IMPORTANT SAFETY WARNING

• PROLONGED CONTINUOUS OPERATION OF AN AMPLIFIER, SPEAKER, OR SUBWOOFER IN A DISTORTED, CLIPPED OR OVER-POWERED MANNER CAN CAUSE YOUR AUDIO SYSTEM TO OVERHEAT, POSSIBLY CATCHING FIRE AND RESULTING IN SERIOUS DAMAGE TO YOUR COMPONENTS AND/OR VEHICLE. AMPLIFIERS REQUIRE UP TO 4 INCHES (10CM) OPEN VENTILATION. SUBWOOFERS SHOULD BE MOUNTED WITH AT LEAST 1 INCH (2.5CM) CLEARANCE BETWEEN THE FRONT OF THE SPEAKER AND ANY SURFACE. KICKER PRODUCTS ARE CAPABLE OF PRODUCING SOUND LEVELS THAT CAN PERMANENTLY DAMAGE YOUR HEARING! TURNING UP A SYSTEM TO A LEVEL THAT HAS AUDIBLE DISTORTION IS MORE DAMAGING TO YOUR EARS THAN LISTENING TO AN UNDISTORTED SYSTEM AT THE SAME VOLUME LEVEL. THE THRESHOLD OF PAIN IS ALWAYS AN INDICATOR THAT THE SOUND LEVEL IS TOO LOUD AND MAY PERMANENTLY DAMAGE YOUR HEARING. PLEASE USE COMMON SENSE WHEN CONTROLLING VOLUME.
• The BTCAN is the next generation in mobile audio systems, combining the innovations of new transfer protocols with KICKER’s finest speaker and amp performance. This audio system has everything you need ready to roll right out of the box. Bluetooth 5.0 and AUX Input, integrated amplifier, RGB lighting, line output, and a wired remote control built to mount in a standard marine panel. And at its heart, the high- powered amp and 6.5” speakers pack a punch with KICKER signature quality audio.
• Use the following instructions to install and operate your BTCAN and BTCAN Remote.

Specifications

• Power Output @ 14.4V, <10% THD+N 70W x 2
• Height [in, mm] 6-5/8, 168
• Width [in, mm] 6-5/8, 168
• Depth [in, mm] 77/8,200
• Weight [lbs, kg] 13.6, 6.2
• Woofer [in, mm] 6-1/2, 160
• Tweeter [in, mm] 1, 25
• Wiring Harness Length [ft, m ] 12, 3.66
• Frequency Response [Hz] 80-20K
• Signal-to-Noise Ratio >102, A-weighted, re: rated power
• Tweeter Magnet Material Neodymium
• Tweeter Dome Material Titanium
• Tweeter Design Dome
• Woofer Cone Material Polypropolene
• Woofer Surround Material Santoprene
• Aux Input Stereo 3.5mm Female 0–1.0 V Sensitivity
• Line Output Stereo 3.5mm Female Buffered, 1V

DIMENSION

Primary (Right)

Secondary (Left)

Installation

Power & Auxiliary Wiring

• Disconnect the vehicle’s battery to avoid an electrical short. Run the black ground wire to a paint-and-corrosion-free, solid, metal area of the vehicle’s chassis or the negative battery terminal. Crimp the provided 5/16” ring terminal to the ground wire. Connect the ring terminal securely to your chosen grounding point
• Run the yellow +12V constant wire to the battery location. Crimp the provided 15A ATC fuse to the yellow wire, which includes a heat-shrink butt connector. Once mechanically crimped, apply heat to the connector to create a secure, insulated connection. Then securely connect the fuse’s 5/16” ring terminal to the positive battery terminal. Note that while the ring terminals can be cut off if necessary, the fuse should always be kept within 18 inches of the battery.
• Connect the Red +12V Ignition Wire to the switched ignition power source, dash-mounted switch, accessory or relay switch.

LED Grille Wiring

1. Connect the female LED plug of the Right BTCAN, located on the smaller, secondary wire loom, to the male LED plug of the Left BTCAN.
2. To control LED Grille behavior, install the KICKER KMLC (sold separately) by connecting the male LED plug of the Right BTCAN, located on the larger, primary wire loom, to the KMLC female plug.

Speaker Wiring
The speaker wiring for the BTCAN comes pre-installed with heat-shrink butt connectors on the Right BTCAN for a fast and secure connection. Connect the Right BTCAN’s speaker wire to the left BTCAN’s speaker wire, then crimp and apply heat.

Mounting
The BTCAN mounts out-of-the-box to round bars with the included 1.5”, 1.75”, and 2” diameter Bar Clamps. Use the KPB Square Clamps (47KPBSQ), sold separately, to mount your BTCAN to square bars. Choose a structurally sound location to mount the BTCAN. The Mounting Base may be rotated ±30° to accommodate some curved bars. Make sure there are no items interfering with the route of the wiring. Installation tools are not provided. 5mm and 6mm Allen Wrenches are required. Using mounting hardware, including clamps and screws, not provided by KICKER will result in a voided warranty.

1. Screw the Mounting Bases to the BTCan using the Mounting Screws.

2. Place the included rubber inserts in the Clamp Rings for improved vibration dampening, then install the Clamp Rings around your bar, securing them to the Mounting Bases using the Clamp Screws.

Operation

Multi-Function Button
Use the multi-function button on top of the Right BTCAN for basic controls.

• Short Press – Change Input Source
• Long Press – Enter Pairing Mode
• Very Long Press – Software Reset
• Double-Press – Play/Pause

A Software Reset will restore the BTCAN to factory settings and wipe the Bluetooth device list.

Status LED
The LED color displays audio source, pairing status, and warnings:

• Off Remote Input wire is low
• Blue Bluetooth Mode
• Blue Blinking Bluetooth Pairing Mode
• Red AUX Mode
• Red Constant Blinking Amp Error
• Red Double Blinking Failure Underr Voltage
• Red Triple Blinking Over Voltage

Setting Input Source

• Short Press the Multi-Function button to switch between Bluetooth (blue) and AUX IN (red) input sources.
• To enter Bluetooth Pairing Mode, Long Press the Multi-Function button while in Bluetooth mode. The STATUS LED will begin to flash blue. You may exit pairing mode at this stage by short pressing the Multi- Function button.
• To finish pairing, from your audio device select ‘BT CANS KICKER’. When successfully connected, the STATUS LED will be solid blue. When the BTCAN powers on in, or enters, Bluetooth mode, it will automatically begin to search for and connect with the last connected device.

Line Output & AUX IN

• To use an external audio device as your input source, connect it to the AUX IN jack using a 1/8” (3.5mm) AUX cable, then set your input source to AUX IN. Ifthe Wired Remote is not installed, use your audio device to control volume.
• To send a line-level signal, connect a 1/8” (3.5mm) AUX cable from the Line Output of the BTCAN to your external audio device’s line-level input.

Remote Control Install

• The BTCAN Remote installs seamlessly into Carling-style cutouts. If performing a custom install, make sure there are no electronics or mechanisms behind the surface area into which you will cut. The mounting hole dimensions are H37mm X W22mm.
• Remote Cutout Dimensions:
  • H: 1.45 inches, 36.83mm
  • W: .85 inches, 21.59mm

IMPORTANT: If the wired remote is not used, keep the cap on the plug to prevent water from damaging the system.

• Push the BTCAN Remote into the cutout, depressing the tabs on the top and bottom, until the BTCAN Remote is secured in the mounting hole cutout (you may not hear a click).

• Route the BTCAN remote wire to the remote input from the Right BTCAN’s larger, primary wire loom.

Remote Control Operation

• Short Press – Change Input Source

• Long Press – Enter Pairing Mode

• Very Long Press – Software Reset

• Double-Press – Play/Pause

• Short Press – Increase Volume by 1 step

• Long Press – Raise Volume until max

• Short Press – Decrease Volume by 1 step

• Long Press – Lower Volume until max

• Short Press – Next Track

• Long Press (Bluletooth) – Fast Forward

• Long Press (AUX) – Raise LED Brightness

• Short Press – Previous Track

• Long Press – Rewind

• Long Press (AUX) – Decrease LED Brightness

Troubleshooting

If the BTCAN becomes frozen or stuck, does not appear to be working, or gives an error code, check the obvious things first such as blown fuses, poor or incorrect wiring connections, etc.

• No power?
  With a Volt Ohm Meter (VOM) check the following:

1. +12 volt power terminal (should read +12V to +16V)
2. Check for reversed power and ground connections
3. Ground terminal, for proper conductivity.
4. Check fuses.

• Power on, no signal?
  Check the following:

1. AUX In/Out connections and cables
2. Test audio source signal, either with a “known good” output device or other means.
3. Audio source volume & BTCAN output volume are increased.

• Bluetooth device will not connect?
  On your mobile device:

1. Turn Bluetooth off, then on again.
2. Remove ‘BT CANS KICKER’ from the Bluetooth menu. Then pair again (see page 11).
3. Move your mobile device closer to the speaker. Avoid obstacles that may block the wireless signal.
4. Perform a software reset by pressing and holding the PLAY/ PAUSE button for 10 seconds (Bluetooth devices must be re-paired after software reset).

• No or low output?

1. Check the settings on the audio source.
2. Check the speaker wiring, including AUX input and Line-level connections.

• BTCAN frozen or stuck in operating procedure?

1. Perform a software reset on the BTCAN
2. Cycle the power.

• No Remote Function?

1. Check wiring.
2. Cycle the power.  

CAUTION: When jump starting the vehicle, be sure that connections made with jumper cables are correct. Improper connections can result in blown fuses as well as the failure of other critical systems in the vehicle.
If you have more questions about the installation or operation of your new KICKER product, see the Authorized KICKER Dealer where you made your purchase. For more advice on installation, click on the SUPPORT tab on the KICKER homepage, www.KICKER.com. Choose the TECHNICAL SUPPORT tab, choose the subject you are interested in, and then download or view the corresponding information. Please E-mail support@ KICKER.com or call Technical Services 405-624-8583 for unanswered or specific questions.

Warranty

When purchased from an Authorized KICKER Dealer, KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of TWO (2) YEARS from date of original purchase with receipt. If this product is identified as “Refurbished” or “B Goods”, the warranty is limited to a period of THREE (3) MONTHS from the date of original purchase. In all cases you must have the original receipt. Should service be necessary under this warranty for any reason due to manufacturing defect or malfunction during the warranty period, KICKER will repair or replace (at its discretion) the defective merchandise with equivalent merchandise. Warranty replacements may have cosmetic scratches and blemishes. Discontinued products may be replaced with more current equivalent products. This warranty is valid only for the original purchaser and is not extended to owners of the product subsequent to the original purchaser. Any applicable implied warranties are limited in duration to a period of the express warranty as provided herein beginning with the date of the original purchase at retail, and no warranties, whether express or implied, shall apply to this product thereafter. Some states do not allow limitations on implied warranties; therefore, these exclusions may not apply to you. This warranty gives you specific legal rights; however you may have other rights that vary from state to state.

WHAT TO DO IF YOU NEED WARRANTY OR SERVICE:

• Defective merchandise should be returned to your local Authorized Stillwater Designs (KICKER) Dealer for warranty service. Assistance in locating an Authorized Dealer can be found at www.KICKER.com or by contacting Stillwater Designs directly. You can confirm that a dealer is authorized by asking to see a current authorized dealer window decal.
• If it becomes necessary for you to return defective merchandise directly to Stillwater Designs (KICKER), call the KICKER Customer Service Department at 405-624-8510 for a Return Merchandise Authorization (RMA) number. Package only the defective items in a package that will prevent shipping damage, and return to:
  • Stillwater Designs
  • 3100 North Husband St
  • Stillwater, OK 74075
• The RMA number must be clearly marked on the outside of the package. Please return only defective components. The return of functioning items increases your return freight charges. Non-defective items will be returned freight-collect to you. For example, if a subwoofer is defective, only return the defective subwoofer, not the entire enclosure. Include a copy of the original receipt with the purchase date clearly visible, and a “proof-of-purchase” statement listing the Customer’s name, Dealer’s name and invoice number, and product purchased. Warranty expiration on items without proof-of-purchase will be determined from the type of sale and manufacturing date code. Freight must be prepaid; items sent freight-collect, or Cash-On-Demand, will be refused.

WHAT IS NOT COVERED?
This warranty is valid only if the product is used for the purpose for which it was designed. It does not cover:

• Damage due to improper installation
• Subsequent damage to other components
• Damage caused by exposure to moisture, excessive heat, chemical cleaners, and/or UV radiation
• Damage through negligence, misuse, accident or abuse. Repeated returns for the same damage may be considered abuse
• Any cost or expense related to the removal or reinstallation of product
• Speakers damaged due to amplifier clipping or distortion
• Items previously repaired or modified by any unauthorized repair facility
• Return shipping on non-defective items
• Products with tampered or missing barcode labels
• Products with tampered or missing serial numbers
• Products returned without a Return Merchandise Authorization (RMA) number
• Products purchased from an UNAUTHORIZED dealer
• Freight Damage
• The cost of shipping product to KICKER
• Service performed by anyone other than KICKER

HOW LONG WILL IT TAKE?
KICKER strives to maintain a goal of one week turnaround for all electronics (amplifiers, crossovers, equalizers, etc.) returns. Delays may be incurred if lack of replacement inventory or parts is encountered. Failure to follow these steps may void your warranty. Any questions can be directed to the KICKER Customer Service Department at 405-624-8510. Contact your International KICKER dealer or distributor concerning specific procedures for your country’s warranty policies.

References

• Car Audio, Home & Personal Audio | KICKER®
• Car Audio, Home & Personal Audio | KICKER®

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>