Sunny Health & Fitness SF-T7632 SPACE SAVING FOLDING TREADMILL USER MANUAL

Sunny Health & Fitness SF-T7632 SPACE SAVING FOLDING TREADMILL

IMPORTANT! Please retain the owner’s manual for maintenance and adjustment instructions. Your satisfaction is very important to us, PLEASE DO NOT RETURN UNTIL YOU HAVE CONTACTED US: [email protected] or 1- 877 – 90SUNNY (877-907-8669).

IMPORTANT SAFETY INSTRUCTION

When using an electrical appliance, basic precautions should always be followed, including the following:
Read all instructions before using this treadmill.
DANGER– To reduce the risk of electrical shock:

Always unplug this appliance from the electrical outlet immediately after using and before cleaning.

WARNING – To reduce the risk of burns, fire, electric shock, or injury to persons:

1.  The treadmill should never be left unattended when plugged in. Unplug from outlet when not in use and before putting on or taking off parts.
2. Use this treadmill only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
3. Never operate this treadmill if it has a damaged cord or plug if it is not working properly, if it has been dropped or damaged, or dropped into water. Return this treadmill to a service center for examination and repair.
4. Keep the cord away from heated surfaces.
5. Never operate the treadmill with the air openings blocked. Keep the air openings free of lint, hair, and similar items.
6. Never drop or insert any object into any opening.
7. Do not use outdoors.
8. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
9. To disconnect, turn the treadmill off, then remove the plug from the outlet.
10. Connect this treadmill to a properly grounded outlet only. See grounding instructions.
    CAUTION:
    To avoid injury, use extreme caution when stepping onto or off of a moving belt. Read instruction manual before using.
    SAVE THESE INSTRUCTIONS

We thank you for choosing our product. To ensure your safety and health, please use this equipment correctly. It is important to read this entire manual before assembling and using the equipment. Safe and effective use can only be achieved if the equipment is assembled, maintained, and used properly. It is your responsibility to ensure that all users of the equipment are informed of all warnings and precautions.

1. Before starting any exercise program, you should consult your physician to determine if you have any medical or physical conditions that could put your health and safety at risk or prevent you from using the equipment properly. Your physician’s advice is essential if you are taking medication that affects your heart rate, blood pressure or cholesterol level.

2. Be aware of your body’s signals. Incorrect or excessive exercise can damage your health. Stop exercising if you experience any of the following symptoms: pain, tightness in your chest, irregular heartbeat, shortness of breath, lightheadedness, dizziness, or feelings of nausea. If you do experience any of these conditions, you should consult your physician before continuing with your exercise program.

3. Keep children and pets away from the equipment. The equipment is designed for adult use only.

4. Use the equipment on a solid, flat level surface with a protective cover for your floor or carpet.
   To ensure safety, the equipment should have at least 2 feet (60CM) of free space all around it.

5. Ensure that all nuts and bolts are securely tightened before using the equipment. The safety of the equipment can only be maintained if it is regularly examined for damage and/or wear and tear.

6. Always use the equipment as indicated. If you find any defective components while assembling or checking the equipment, or if you hear any unusual noises coming from the equipment during exercise, discontinue use of the equipment immediately and do not use until the problem has been rectified.

7. Wear suitable clothing while using the equipment. Avoid wearing loose clothing that may become entangled in the equipment.

8. Do not place fingers or objects into the moving parts of the equipment.

9. The maximum weight capacity of this unit is 220 pounds (100 KG).

10. The equipment is not suitable for therapeutic use.

11. To avoid bodily injury and/or damage to the product or property, proper lifting and moving is required.

12. Your product is intended for use in cool, dry conditions. You should avoid storage in extreme cold, hot or damp areas as this may lead to corrosion and other related problems.

13. This equipment is designed for indoor and home use only, it is not intended for commercial use!

IMPORTANT OPERATING INSTRUCTIONS

1. Insert the power plug directly into the socket.
2. Read the manual before operating the equipment.
3. Speed changes do not occur immediately. Set your desired speed using the adjustment keys on the main console. The speed will increase gradually.
4. While on the treadmill, move with caution as distractions may cause you to lose balance and stray from walking in the center of the belt. This may result in serious injury.
5. This unit starts at a very low speed. To begin use, hold onto the handrails and stand on the side rails while it starts up, then step onto the belt once it’s in motion.
6. Always hold the handrail when making changes in the settings.
7. A safety key is provided for emergency use. The machine will function only if the safety key is inserted into the computer console. In case of emergency, remove the safety key to immediately stop the belt and shut off the treadmill. The display screen will reset once the safety key is reinserted.
8. The console control keys are precisely set and require very little finger pressure to use. To avoid damaging these keys, do not use excessive pressure when operating these controls.
9. This equipment is designed for adult use only! Children should not be allowed to use or play near this equipment. When present, children should always be supervised by an adult.
10. Women who are pregnant or nursing should consult a physician before attempting to begin any exercise program.
11. Always stay hydrated during and after exercise.
    IMPORTANT NOTE:
    The belt must be lubricated before the first use! Please see Page 12 for instructions on how to properly apply lubricant.

EXPLODED DIAGRAM

PARTS LIST

No.| Description| Specification| Qty| | No.| Description| Specification| Qty
---|---|---|---|---|---|---|---|---
A01| Base Frame| | 1| C27| Safety Key| | 1
A02| Main Frame| | 1| C28| Handle Bar Decoration Ring| | 2
A03| Console Bracket| | 1| D01| Console Display| | 1
A04| Motor Frame| | 1| D02| Control Board| | 1
A05| Adjustable Frame| | 1| D03| Keyboard| | 1
A06| Base Support Tube L/R| | 2| D04| Top Signal Wire| | 1
A07| Running Board Strengthen Tube| | 1| D05| Middle Signal Wire| 1150mm| 1
B01| Front Roller| | 1| D06| Lower Signal Wire| 1600mm| 1
B02| Rear Roller| | 1| D07| Speed Sensor| 200mm| 1
B03| Spanner with Screw Driver| S=13,14,15| 1| D08| DC Motor| | 1
B04| Allen Wrench| S5| 1| D09| AC Single Line| Blue 350mm| 1
B05| Locking Pin Iron| | 1| D10| AC Single Line| Blown 350mm| 1
B06| Pressure Spring| | 1| D11| Power Switch| | 1
B07| Safety Key Plate| | 1| D12| Running Board| | 1
B08| Transport Wheel Bushing| | 4| D13| Magnetic Ring| | 1
B09| Lock Knob| | 1| D14| Magnetic Core| | 1
C01| Console Top Cover| | 1| D15| Power Wire| 2150mm| 1
C02| Console Bottom Cover| | 1| D16| Filter| | 1
C03| Left Upright Tube Cover| | 1| D17| AC Single Line| 350mm| 1
C04| Right Upright Tube Cover| | 1| D18| AC Single Line| 350mm| 1
C05| Left Upright Tube Inside Cover| | 1| E01| Nut| M6| 6
C06| Right Upright Tube Inside Cover| | 1| E02| Nut| M8| 6
C07| Motor Top Cover| | 1| E03| Bolt| M1060| 2
C08| Motor Bottom Cover| | 1| E04| Bolt| M850| 2
C09| Left Rear Cover| | 1| E05| Bolt| M815| 4
C10| Right Rear Cover| | 1| E06| Bolt| M1090| 1
C11| Motor Cover Buckle| | 1| E07| Bolt| M645| 1
C12| Side Rail| | 2| E08| Bolt| M655| 2
C13| Running Belt| | 1| E09| Flat Washer C| Φ10| 2
C14| Rubber Cushion| | 6| E10| Bolt| M6*28| 4

C15

| ****

Blue Cushion

| | ****

2

| ****

E11

| ****

Bolt

| M5*12

(including washer)

| ****

2

C16| Motor Belt| | 1| E12| Bolt| M5*8

(including washer)

| 16
C17| Transportation Wheel| | 2| E13| Screw| ST4.212| 27
C18| C Shape Foot Pad 1| | 2| E14| Screw| ST2.98| 2
C19| C Shape Foot Pad 2| | 2| E15| Screw| ST2.96| 9
C20| Ring Protecting Wire Plug| | 2| E16| Screw| ST4.212| 6
C21| Power Wire Buckle| | 1| E17| Washer| Φ6| 3
C22| Cushion| | 1| E18| Washer| Φ8| 2
C23| Inner Cap| | 2| E19| Washer| M625| 2
C24| Fixed Block| | 1| E20| Arc Washer| Φ8| 6
C25| Locking Pin| | 1| E21| Spring Washer| Φ8| 2
C26| Rubber Cushion| | 1| E22| Flat Washer C| Φ8| 2
No.| Description| Specification| Qty| | No.| Description| Specification| Qty
---|---|---|---|---|---|---|---|---
E23| Bolt| M848| 2| E26| Bolt| M860| 1
E24| Bolt| M848| 2| E27| Bolt| M6*46| 2
E25| Nut| M10| 1| | | |

HARDWARE PACKAGE

Ordering Replacement Parts (U.S. and Canadian Customers only)
Please provide the following information in order for us to accurately identify the part(s) needed:

• The model number (found on the cover of the manual)
• The product name (found on the cover of the manual)
• The part number found on the “EXPLODED DIAGRAM” and “PARTS LIST” (found near the front of the manual)
  Please contact us at [email protected] or 1- 877 – 90SUNNY (877-907-8669).

ASSEMBLY INSTRUCTIONS

We value your experience using Sunny Health and Fitness products. For assistance with parts or troubleshooting, please contact us at [email protected] or 1-877-90SUNNY (877-907- 8669).

1. STEP 1:
   NOTE : We recommend having two people do the assembly.
   Open the carton box and remove the contents. Place the Main Frame (No. A02) on level ground. Ensure that you have a work area that is clean and has adequate space.

2. STEP 2:
   NOTE : Support the Main Frame (No. A02) at position “F” with one hand to prevent it from falling down during assembly.
   Attach the Left Base Support Tube (No. A06) to the Base Frame (No. A01). Use Allen Wrench (No. B04) and Spanner with Screw Driver (No. B03) to screw Bolt (No. E04), 2 Arc Washers (No. E20), and Nut (No. E02) into the Base Frame (No. A01). Then, screw the Bolt (No. E05) and Arc Washer (No. E20) into the Base Frame (No. A01).
   Repeat the step above to assemble the Right Base Support Tube (No. A06) to the Base Frame (No. A01).
   We value your experience using Sunny Health and Fitness products. For assistance with parts or troubleshooting, please contact us at [email protected] or 1-877-90SUNNY (877-907- 8669).

3. STEP 3:
   NOTE : To avoid any possible injury, please hold on to the Main Frame (No. A02) at position “F” before you pull the Locking Pin (No. C25) and ensure that the space directly underneath it is clear of any objects. Once the Main Frame (No. A02) is released, please continue to hold on until it reaches the floor.
   Pull the Locking Pin (No. C25) and lower the Main Frame (No. A02) to the floor.
   NOTE : The Locking Pin (No. C25) will snap back into the treadmill. It does not detach from the treadmill.

4. STEP 4:
   Connect the Top Signal Wire (No. D04) to the Middle Signal Wire (No. D05).
   We value your experience using Sunny Health and Fitness products. For assistance with parts or troubleshooting, please contact us at [email protected] or 1-877-90SUNNY (877-907- 8669).

5. STEP 5:
   Attach the Console Bracket (No. A03) to the Base Frame (No. A01) with 2 Bolts (No. E24). Tighten using Allen Wrench (No. B04).

6. STEP 6:
   Attach the Left & Right Upright Tube Covers (No. C03 & No. C04) and Left & Right Upright Tube Inside Covers (No. C05 & No. C06) to the Base Frame (No. A01) and Console Bracket (No. A03) with 8 Screw (No. E13). Tighten using Spanner with Screw Driver (No. B03).
   We value your experience using Sunny Health and Fitness products. For assistance with parts or troubleshooting, please contact us at [email protected]  or 1-877-90SUNNY (877-907- 8669).

7. Insert Lock Knob (No. B09). Secure the Base Frame (No. A01) to Main Frame (No. A02) by turning Lock Knob (No. B09) clockwise until tight.
   The assembly is complete!
   IMPORTANT NOTE!
   You will need to lubricate your treadmill before the first use. See Page 12.

MAINTENANCE & CARE

General cleaning will help prolong the life and performance of your treadmill. Keep the unit clean and maintained by dusting the components regularly. Clean both sides of the Running Belt (No. C13) to prevent dust from accumulating underneath. Keep your running shoes clean so that dirt from your shoes does not wear out the Running Board (No. D12) and Running Belt (No. C13). Clean the surface of the Running Belt (No. C13) with a clean damp cloth.
To better maintain the treadmill and prolong its life it is suggested that the treadmill be powered off for 10 minutes every 2 hours and fully powered off whenever not in use.
A loose Running Belt (No. C13) will result in the runner sliding off when running, while too tight of a Running Belt (No. C13) will negatively affect the motor’s performance and create more friction between the roller and Running Belt (No. C13). The most suitable tightness for the Running Belt (No. C13) is pulled out 50-75mm from the Running Board (No. D12).

CENTERING THE RUNNING BELT:
Place the treadmill on level ground and set it at 3-5MPH to check if the Running Belt (No. C13) drifts.

1. If the Running Belt (No. C13) moves to the right, turn the adjusting bolt on the right side ¼ turn clockwise, then turn the left adjustment bolt ¼ turn counter-clockwise.
2. If the Running Belt (No. C13) does not move, repeat this step until it centers. Refer to Figure A.If the Running Belt (No. C13) moves to the left, turn the adjusting bolts on the left side ¼ turn clockwise, then turn the right adjustment bolt ¼ turn counter-clockwise. If the Running Belt (No. C13) does not move, repeat this step until it centers. Refer to Figure B.
3. Over time, the Running Belt (No. C13) will loosen. To tighten the Running Belt (No. C13) turn the Left and right side adjustment bolts one full turn clockwise, and check the tension of the Running Belt (No. C13). Continue this process until the Running Belt (No. C13) is at the correct tension. Make sure to adjust both sides equally to ensure correct belt alignment. Refer to Figure C.

LUBRICATING THE TREADMILL

*IMPORTANT NOTE:
You will need to lubricate your treadmill before the first use.

RUNNING BELTS & TREADMILL LUBRICANT:
Lubricating the Running Board (No. D12) and Running Belt (No. C13) is essential as the friction between the two affects the life span and function of the treadmill, therefore it is suggested that the Running Board (No. D12) and Running Belt (No. C13) be inspected regularly. Should you find any wear on the Running Board (No. D12), please contact us at: [email protected].

WARNING : Always unplug the treadmill from the electrical outlet before cleaning, lubricating, or repairing the unit.
HOW TO LUBRICATE:

1. Raise the Running Belt (No. C13) up on one side and apply lubricant to the Running Board (No. D12). Use a rag to thoroughly wipe the lubricant over the Running Board (No. D12). Repeat this process for the other side.
2. The moving parts should turn freely and quietly. Abnormal moving parts will affect the safety of the equipment. Inspect and tighten bolts regularly.
3. To better maintain the treadmill and prolong its lifespan, it is suggested that maintenance be done regularly.

FOLDING INSTRUCTIONS

FOLDING:

• Loosen the Lock Knob (No. B09) counter-clockwise and pull it out. Fold up the Main Frame (No. A02).
  NOTE : Remember where you keep the Lock Knob (No. B09) after you pull it out. You will need it when you unfold the treadmill.

• Pull out the Locking Pin (No. C25) with one hand, then lift up the Mainframe at position “F” with the other hand until the Locking Pin (No. C25) snaps into the hole of Fixed Block (No. C24).

UNFOLDING:
NOTE : Before lowering the Main Frame (No. A02), ensure that the space directly underneath it is clear of any objects.

• To avoid any possible injury, please hold on the Main Frame (No. A02) at position “F” before you pull the Locking Pin (No. C25). Once the Main Frame (No. A02) is released, continue to hold on at position “F” until it reaches the floor.
• Secure Base Frame (No. A01) into Main Frame (No. A02) by inserting Lock Knob (No. B09) and turning clockwise until tig

HOW TO MOVE THE MACHINE

Before attempting to move the treadmill, please make sure that it has been properly folded. Unplug the power cord. To tilt, start by placing one hand at position “P” to support the top end of the treadmill.
Next, place one foot at position “K” to hold the bottom end of the treadmill steady. With your foot at “K”, slowly tilt the top of the treadmill downward toward the ground. Once the Main Frame “P” reaches a low enough point, the wheels of the treadmill touch the ground.

To transport, hold the treadmill from position “P” and tilt until the wheel’s “K” can move on the ground.

HOW TO USE SAFETY KEY

Secure Base Frame (No. A01) into Main Frame (No. A02) by inserting Lock Knob (No. B09) and turning clockwise until tight.
Insert the Safety Key (No. C27) into the magnetic area of the Console Display (No. D01) and clip it to your clothes.
Note : In an emergency, pull out the Safety Key (No. C27), and the treadmill will stop.

IMPORTANT ELECTRICAL INFORMATION

WARNING: This treadmill requires a power source of 8 amps (100-120 V) in order to properly operate. For your safety, as well as the safety of others, verify that the power source is correct before plugging in the equipment. Any power source above or below this level could cause significant damage to the equipment and or user.
GROUNDING METHODS:
This product must be grounded. Grounding provides the least resistance for electrical current and will reduce the risk of electric shock. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. Ensure that the product is connected to an outlet that contains the same configuration as the plug. Do not use an adaptor for this product.
This product is for use on a nominal 100-120V circuit and has a grounding plug that looks like the plug illustrated in sketch A. Make sure that the product is connected to an outlet having the same configuration as the plug. No adapter should be used with this product.
DANGER :
Improper connection of the equipment-grounding conductor can result in risk of electric shock.
Check with a certified electrician if you are in doubt as to whether the product is properly grounded.
Do not modify the plug provided with the product. If it will not fit the outlet, have a proper outlet
installed by an electrician.
WARNING!

1. NEVER use a ground fault circuit interrupt (GFCI) wall outlet with this treadmill. Route the power cord away from any moving part of the treadmill including the elevation mechanism and transportation wheels.
2. NEVER operate the treadmill using a generator or UPS power supply.
3. NEVER remove any cover without first disconnecting AC power.
4. NEVER expose the treadmill to rain or moisture. This treadmill is not designed for use outdoors, near pools, or in any other high-humidity environment.

GROUNDING METHOD

THE DISPLAY CONSOLE

DISPLAY

• SPEED : Displays current speed (range 0.5-7.0MPH). When in setting mode, the window displays H-1, H-2, H-3.
• TIME : Displays the running time. Displays the exercise time from 0:00-99:59 MINS. If the time reaches 99:59, the treadmill will stop smoothly and display “End” and will enter standby mode after 5 seconds. When in countdown mode, it will count from the setting time to 0:00. When the countdown reaches 0:00, the treadmill will stop smoothly and show “End” and will enter into standby mode after 5 seconds.
• DISTANCE : Displays the distance traveled (range 0.00-99.9 MILES). When the clock reaches 99.9, it will reset to 0.00 and begin counting again from 0.0. When in countdown mode, it will count down from the distance you set to 0.00. When it reaches 0.00, the treadmill will stop smoothly and display “End”, then enter standby mode after 5 seconds.
• CALORIES : Displays the user’s calories burned (range 0-999 calories). When it reaches 999, it will start again from 0. In countdown mode, it will count from the number of calories you set to 0. When it reaches 0, the treadmill will stop smoothly and show “End”, and then enter standby mode after 5 seconds.
  PROGRAMS| Initial| Default Value| Set Range| Display Range
  ---|---|---|---|---
  TIME(MIN:SECOND)| 0:00| 15:00| 5:00-99:00| 0:00－99:59
  SPEED(MPH)| 0.5| 0.5| 0.5-7.0| 0.5-7.0
  DISTANCE(MILE)| 0| 1.0| 0.5-99.9| 0.0－99.9
  CALORIE(KCAL)| 0| 50| 10-999| 0－999

FUNCTION KEYS

• START : To start the treadmill, insert the magnet end of the safety key into the computer console then press the START button. This treadmill requires the Safety Key to start. 0.5 MPH is the default start speed.
• STOP : This button can PAUSE and STOP the treadmill. When in use, press this button once to PAUSE your workout and the current workout data will still be shown. Press STOP again to end your workout session and all data from this session will be deleted.
• MODE : Press this button to select a MODE. Pressing once will enter H1, the TIME countdown mode starting from 15:00 MINS. H2 is the DISTANCE countdown mode starting from 1.00 MILE and H3 is the CALORIES countdown mode which starts from 50 KCAL. When setting each mode, you can press +/- to increase or decrease the preset H1, H2, and H3 settings then press START to start the treadmill.
• SPEED +/ SPEED –: Press the SPEED +/- buttons to increase or decrease the speed in increments of 0.1 MPH. Pressing and holding either of these buttons for over 0.5 seconds will increase or decrease the speed continually.
• LUBRICATION REMINDER
  Your treadmill needs lubrication maintenance every 188 miles. When it is time for maintenance, the treadmill beeps every 10 seconds and displays an “OIL” icon on your LCD. Please read the LUBRICATING THE TREADMILL on Page 12 to learn the proper steps to lubricating your treadmill. Apply the lubricant to the middle of the running board on both sides. After application, press and hold the STOP button for 3 seconds to clear the “OIL” reminder.

TREADMILL FUNCTIONS

• SAFETY LOCK FUNCTION:
  Removing the Safety Key (No. C27) from the computer console while the treadmill will stop the treadmill immediately. Once the treadmill reaches a full stop, the display will show “- – -” and the treadmill will beep 3 times. To start the treadmill again, insert the magnet end of the Safety Key (No. C27) into the computer console and press the START button.

• POWER SAVE FUNCTION:
  When the treadmill has been inactive for 10 minutes, it will enter Power Saving Mode. While the treadmill is in this mode, the display will be turned off. To turn it back on, press any button.

• POWER ON:
  Flick the power switch to this symbol to turn on the treadmill.

• POWER OFF:
  Flick the power switch to this symbol to turn the treadmill off at any time, including while the treadmill is in use.

SAFETY NOTE:

1. We recommend that you maintain a slow speed at the beginning of a session and hold the handrails until you become familiar with the treadmill.
2. Insert the magnet end of the Safety Key (No. C27) into the computer console and attach the safety clip to your clothing before starting your workout. To end your workout, press the STOP button or remove the Safety Key (No. C27) and the treadmill will stop immediately.

EXERCISE INSTRUCTIONS

GETTING STARTED:
Get to know your treadmill. Before attempting to use the treadmill, take some time to familiarize yourself with the controls. Once you get on, stand with your feet on the side rails and stabilize yourself by holding onto the handrails.
Next, attach the clip end of the Safety Key (No. C27) to your clothes and insert the magnetic end of the key into the computer console. Press the START button to start the treadmill. The treadmill will start at the system default setting speed of 0.5 MPH. Step onto the belt. When you feel comfortable, slowly increase this speed. When you are finished with your workout, press the STOP button to stop the treadmill or you can remove the magnetic end of the Safety Key (No. C27) to stop the treadmill.

TROUBLESHOOTING

The treadmill will not start

| ****

Not plugged in.

| ****

Plug cord into the outlet.

Safety Key not inserted.| Insert Safety Key.

The running belt not centered

| The running belt tension is not correct on the left or right sides of the running board.| Tighten the adjustment bolts on the left and right side of the rear roller.

Computer not working

| Wires from the computer and bottom control board not properly connected.| Check wire connections from the computer to the control board.| ****

the

The transformer is damaged.| If the transformer is damaged, contact customer service.

E01

failure

| ****

or

| ****

E13:    Message

| **** Wires from the computer and bottom control board are not properly connected.| Check wire connections from the computer to the control board. If the wire has been punctured or damaged, you will need to replace it. If the problem is not rectified, you may need to replace the control board.

E02: Burst clash protection

| The incoming voltage is lower than 50% of the required voltage.| Check that the incoming power supply is the correct voltage.

E03:

signal

| ****

No

| ****

speed    sensor

| The speed sensor signal cannot be received by the control board.| Check that the sensor wire is properly connected. If damaged, replace the wire. Check to see if the magnetic sensor is damaged, replace if necessary.
E05: Current overload protection (Self Protecting System)| ****

The incoming voltage is too low or too high. The control board is damaged.

| Restart the treadmill. Check the incoming voltage to ensure it is correct. Check the control board, and replace if damaged.
A moving part of the treadmill is stuck and therefore the motor is unable to rotate properly.| Inspect moving parts of the treadmill to ensure that they are operating correctly. Check the motor, listen for strange noises, and check for a burning smell. Replace the motor if necessary.
E06: Motor Abnormality| ****

The motor wire is not connected, or the motor is damaged.

| Check motor wires to see if the motor is connected. If the wire has been punctured or damaged, you will need to replace it. If the problem is not rectified, you may need to replace the motor.
---|---|---
E08:        Control        Board Abnormality| ****

The control board is not connected.

| Check the upper and middle wires to see if the control board is connected. If the wire has been punctured or damaged, you will need to replace it. If the problem is not rectified, you may need to replace the control board.
E10: Motor Abnormality| ****

The motor is short-circuited.

| ****

Replace with a new motor.

A moving part of the treadmill is stuck and therefore the motor is unable to rotate properly.

| Inspect moving parts of the treadmill to ensure that they are operating correctly and lubricate the treadmill Replace the motor if necessary.

NOTE : If you are unable to resolve an issue using the troubleshooting guide above, please contact Customer Service at [email protected]

FAQs

How is the Sunny Health & Fitness SF-T7632 treadmill powered?

Answer: The treadmill is powered by plugging it into a standard electrical outlet.

Can you adjust the incline level on the Sunny Health & Fitness SF-T7632 treadmill?

Answer: No, this treadmill does not have an adjustable incline feature.

Is the Sunny Health & Fitness SF-T7632 treadmill suitable for both walking and running?

Answer: Yes, it is designed for both walking and running workouts.

Does the Sunny Health & Fitness SF-T7632 treadmill come with preset workout programs?

Answer: Yes, it comes with several preset workout programs to help you achieve your fitness goals.

What is the maximum speed that the Sunny Health & Fitness SF-T7632 treadmill can reach?

Answer: The SF-T7632 treadmill has a maximum speed of 9 miles per hour (14.5 kilometers per hour).

Can you describe the dimensions of the Sunny Health & Fitness SF-T7632 when it is folded for storage?

Answer: When folded, the SF-T7632 measures approximately 29.5 inches in length, 23 inches in width, and 53 inches in height.

What is the maximum weight capacity of the Sunny Health & Fitness SF-T7632 treadmill?

Answer: The Sunny Health & Fitness SF-T7632 has a maximum weight capacity of approximately 220 pounds (100 kg).

What are the key features of the Sunny Health & Fitness SF-T7632 SPACE SAVING FOLDING TREADMILL?

Answer: The Sunny Health & Fitness SF-T7632 is a folding treadmill designed for space-saving convenience. It features a compact design, a digital monitor, and a powerful motor for workouts at home.

Can the Sunny Health & Fitness SF-T7632 treadmill be easily moved when folded?

Answer: Yes, it has transportation wheels for easy maneuverability when folded, making it convenient to store and move around.

Is there a warranty included with the purchase of the Sunny Health & Fitness SF-T7632 treadmill?

Answer: Warranty information may vary depending on the retailer or manufacturer. Be sure to check the warranty details when making your purchase.

What type of display does the Sunny Health & Fitness SF-T7632 treadmill have?

Answer: It has a digital LCD display that shows various workout metrics, such as time, speed, distance, and calories burned.

Does the Sunny Health & Fitness SF-T7632 treadmill have a safety key or emergency stop feature?

Answer: Yes, it comes with a safety key and an emergency stop feature for added safety during workouts.

Video- Sunny Health & Fitness SF-T7632 Space Saving Folding Treadmill

w/LCD Display

Download This Manual PDF:Sunny Health & Fitness SF-T7632 SPACE SAVING FOLDING TREADMILL USER MANUAL

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>