LIANQIAN GJ807 4 in 1 Multifunctional Food Cutter And Slicer Instruction Manual

 Food Processor

GJ807

Instruction Manual

Please read this instruction manual carefully before using the product, and keep it for reference after reading

Respected user:
Thank you for using this product. In order to facilitate your correct operation of this machine, please read this manual carefully before use. Please be sure to read Chapter 1 “Safe Attention” carefully.
(The technical specifications in this manual are subject to change without prior notice)

Chapter 1: Safety Attention

1. Before cleaning, assembling or disassembling this product, cut off the power supply.
2. Do not place the product within the reach of children.
3. The product cannot be used by children or persons with physical, sensory or mental impairments, unless they are supervised and instructed in relation to the use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with this product.
4. When turning off the power supply or replacing accessories, stop the machine first.
5. When cutting food, you must use small food pushers and large food pushers. Do not use the machine if these components are lost or damaged.
6. If the power supply cord is damaged, in order to avoid danger, it must be replaced by the manufacturer, maintenance department or professionals from similar departments.
7. Risk of injury! Use extreme caution when cleaning or moving blades.
8. Danger of electric shock! Never attempt to repair the product yourself. In case of malfunction, have it repaired by qualified service personnel.
9. Warning! Do not put the main machine into the water for cleaning, only to scrub with a wet towel. Allow the machine to cool down sufficiently before washing.
10. Check whether the power supply voltage specified by the product is consistent with the power supply voltage (only refers to AC power).
11. Avoid damage to the power cord. Do not squeeze, bend or rub with sharp objects, keep away from heat and fire, and keep the power cord away from the blade.
12. The power cord should be laid flat, and do not pull it to cause the product to fall and malfunction.
13. If more sockets are added (extending the socket power cord), the equipment must match the power supply voltage of the product. Do not use the universal socket with other electrical appliances at the same time.
14. Do not use the product on wet ground, do not touch the product or the power cord plug with wet hands.
15. Do not disassemble the interior of the product at will, and do not let objects enter or insert into the interior of the product, causing malfunction and damage.
16. Only the accessories provided by the manufacturer can be used. If any failure occurs due to the use of accessories from other manufacturers, the company will not be responsible, and such failures and damages are not included in the warranty.
17. Please do not use it on unstable, wet or heat labile surface to avoid damage or failure.
18. Do not place the product directly on fire or near heat or fire sources, otherwise the product will be damaged or malfunction, or even be dangerous.
19. Do not insert the power cord into the socket when not in use. The plug must be unplugged in the following cases: after use; before cleaning; maintenance.
20. When the plug is inserted into the socket, it must be inserted to the end, otherwise the components will be overheated and burned due to bad contact.
21. The company shall not be responsible for any faults caused by improper use of this product or failure to comply with this manual, and such faults and damages are not covered by the warranty.
22. Never leave the machine working unattended.
23. If the machine works for a long time or the working environment’s temperature is too high, causing the motor to overheat and stop, please turn off the power immediately, stop it for more than half an hour, and start the machine after the motor cools down.
24. Keep hands, hairs, clothes and tableware away from the blade when operating the product to avoid injury and damage to the product.
25. Once a part of the product is on fire, do not put out the fire directly with water. You must disconnect the power supply and cover the burning part with a damp cloth to extinguish the fire.
26. Plastic packaging bags, please store them well and keep them away from children, which may cause suffocation risk.
27. Do not immerse the aluminum alloy housing and power cord in any liquid.

Do not use the product under the following conditions:

1. The product or power cable is faulty.
2. The product accidentally falls, causing damage or abnormal operation.

If the above situation occurs, please send the product to the after-sales service of the manufacturer for processing, please use the original accessories of the product.

Chapter 2: Components and Functions

Name of Components

1. Large food pusher
2. Small food pusher
3. Aluminum alloy lip
4. Spring buckle
5. Aluminum alloy housing
6. Waterproof switch
7. Diced knife holder
8. Dicing knife net
9. Dicing knife
10. Tighten handle
11. Slicing disc
12. Shredding disc (2mm)
13. Food pusher
14. Slitting knife
15. Slicer spacer
16. Shredding knife set (3mm)

Be aware of the functions of the main components before operating the

product:

1. Large food pusher: press the long and thin food into the feeding port for slicing or shredding or dicing.
2. Small food pusher: press thick or irregular food into the feeding port for slicing, shredding, or dicing.
3. Aluminum alloy lip: the right side of the aluminum alloy lip is buckled with a safety ejector bar. The machine can only work when the aluminum alloy lip is put on the aluminum alloy housing. The machine cannot work before the aluminum alloy housing is not covered with the aluminum alloy lip.
4. Spring buckle: firmly fix the aluminum alloy lip on the aluminum alloy housing to ensure that the aluminum alloy lip will not come off when the machine is working.
5. Aluminum alloy housing: the main body of machine.
6. Waterproof switch: turn on / turn off the power.
7. Diced knife holder: a holder for placing and fixing the dicing knife net.
8. Dicing knife net: cut the thick pieces of food with a dicer into square shapes again.
9. Dicing knife: cut the food that needs to be diced into thick slices and press it into the dicing knife net to make the food diced.
10. Tighten the handle: tighten the screw to the left to tighten the dicing knife on the motor shaft.
11. Slicing disc: fix it on the motor shaft and cut the food into slices.
12. Shredding disc (2mm): fixed on the motor shaft, cut the food into 2mm shreds.
13. Food Pusher: push the processed food to the discharge port.
14. Slitting knife: slit food into strips , such as French fries.
15. Slicer spacer: add this set of spacers under the slicing knife of the slicing disc or shredding disc, to increase the thickness of the slices or shreds 1 mm.
16. Shredding disc (3mm): fixed on the motor shaft, cut the food into 3mm shreds.

Chapter 3: Usage Method

Pay attention! The correct orientation when the food pusher is

installed:

1. Usage of Dicing

Note: Tighten the handle must be tightened with a spanner

(1) Insert the pusher into the bottom of the flat part of the motor shaft according to Figure 1.
(2) Put the dicing knife holder and the dicing knife net into the aluminum alloy housing in turn according to Figure 2.
(3) Put the dicing knife on the motor shaft according to Figure 3, and then turn left to tighten the tightening screw. It must be tightened counterclockwise with a spanner.
(4) Put the aluminum alloy lip onto the aluminum alloy housing according to Figure 4, and then fasten the spring buckles to the buckle ears of the aluminum alloy lip.
(5) Insert the small food pusher and the large food pusher into the feeding port of the aluminum alloy lip according to Figure 5, as shown in Figure 6.
(6) Clean the food that needs to be diced. If the food is too large to pass through the feed port, use a knife to cut the food to a size that can pass through the feed port.
(7) After preparation, insert the machine plug into the 120VAC/60Hz power socket, press the waterproof switch to start the machine, and confirm whether the machine is running smoothly. If there is any abnormality, stop the machine for inspection. If no, it can be normal for dice.
(8) Put the prepared food in from the feeding port, use the combination of the small food pusher and the large food pusher to lightly press the food, the food will be processed by the rotating dicing blade, and then fall from the mouth of machine. If the food is elongated and can pass through the middle hole of the small food pusher, you can put the small food pusher on the feeding port, put the food from the middle hole of the small food pusher, and press lightly with the large food pusher, it can reduce the shaking of the food and greatly improve the dicing effect.
(9) After cutting the food, press the waterproof switch to turn off the machine. After the machine stops running completely, unplug the power cord of the machine, then remove the accessories and clean the food and machine according to the Figure 5 to Figure 1.

2. Usage of Slitting:

Note: Tighten the handle must be tightened with a spanner

(1) The food pusher needs to be aligned with the oblate axis of the motor according to Figure 1.
(2) Put the dicing knife holder and the slitting knife on the aluminum alloy housing according to Figure 2.
(3) Put the dicing knife on the motor shaft according to Figure 3, and then tighten the screw counterclockwise (Note: Tighten the handle must be tightened with a spanner).
(4) Put the aluminum alloy lip onto the aluminum alloy housing according to Figure 4, and then fasten the spring buckles to the buckle ears of the aluminum alloy lip.
(5) Insert the small food pusher and the large food pusher into the feeding port of the aluminum alloy lip according to Figure 5, as shown in Figure 6.
(6) Clean the food that needs to be slit into strips. If the food is too large to pass through the feeding port, use a knife to cut the food to a size that can pass through the feeding port.
(7) When ready, insert the plug into the 120VAC/60Hz power socket, press the spring buckle to start the machine, and confirm whether the machine is running smoothly. If there is any abnormality, you need to stop the machine for inspection. If there is no abnormality, you can slit strips normally.
(8) Put the prepared food into the feeding port, use the Large Food Pusher and the Small Food Pusher to press the food, the food will be processed by the dicing knife and the slitting knife, and then fall from the mouth of the main machine. If the shape of food is long and thin, you can cut the food into long strips according to the length of the feed port, put it horizontally into the feed port, and then use the Large Food Pusher and the Small Food Pusher to press the food lightly, so that the food can be cut out for longer food, avoid slitting food too short vertically, thus greatly improving the slitting effect.
(9) After slitting the food, press the switch to turn off the machine. After the machine stops running completely, unplug the power cord of the machine, then remove the accessories and clean them according to the Figure 5 to Figure

3. Usage of Slicing:

(1) Insert the pusher into the bottom of the flat part of the motor shaft according to Figure 1.
(2) Put the slicer disc on the motor shaft according to Figure 2.
(3) Put the aluminum alloy lip on the aluminum alloy housing according to Figure 3, and then fasten the spring buckles to the buckle ears of the aluminum alloy lip.
(4) According to Figure 4, put the small food pusher and the large food pusher into the feeding port of the aluminum alloy lip, as shown in Figure 5.
(5) Clean the food that needs to be sliced. If the food is too large to pass through the feed port, use a knife to cut the food to a size that can pass through the feed port.
(6) After preparation, insert the machine plug into the 120VAC/60Hz power socket, press the waterproof switch to start the machine, and confirm whether the machine is running smoothly. If there is any abnormality, stop the machine for inspection. If no, it can be normal for slice.
(7) Put the prepared food into the feeding port, use the small food pusher and the large food pusher together to lightly press the food, the food will be processed by the rotating slicing blade, and then fall from the mouth of machine. If the food is elongated and can pass through the middle hole of the small food pusher, you can put the small food pusher on the feeding port, put the food from the middle hole of the small food pusher, and press lightly with the large food pusher, which can reduce the shaking of food and greatly improve the slicing effect.
(8) After cutting the food, press the waterproof switch to turn off the machine. After the machine stops running completely, unplug the power cord of the machine, and then remove the accessories and clean the food and machine according to the Figure 5 to Figure 1.

4. Usage of Shredding:

(1) Put the pusher into the bottom of the flat part of the motor shaft according to Figure 1.
(2) Put the shredding disc on the motor shaft according to Figure 2.
(3) Put the aluminum alloy lip on the aluminum alloy housing according to Figure 3, and then fasten the spring buckles to buckle ears of the aluminum alloy lip.
(4) According to Figure 4, put the small food pusher and the large food pusher into the feeding port of the aluminum alloy lip, as shown in Figure 5.
(5) Clean the food that needs to be shredded. If the food is too large to pass through the feed port, use a knife to cut the food to a size that can pass through the feed port.
(6) After preparation, insert the machine plug into the 120VAC/60Hz power socket, press the waterproof switch to start the machine, and confirm whether the machine is running smoothly. If there is any abnormality, stop the machine for inspection. If no, it can be normal for shred.
(7) Put the prepared food in from the feeding port, use the combination of the small food pusher and the large food pusher to lightly press the food, the food will be processed by the rotating shredding blade, and then fall from the mouth of machine. If the food is slender and can pass through the middle hole of the small food pusher, you can put the small food pusher on the feeding port, put the food from the middle hole of the small food pusher, and press lightly with the large food pusher, it can reduce the shaking of the food and greatly improve the shredding effect.
(8) After cutting the food, press the waterproof switch to turn off the machine. After the machine stops running completely, unplug the power cord of the machine, then remove the accessories and clean the food and machine according to the Figure 5 to Figure 1.

5. Usage of Slicer Spacer and Shredding Knife Set (3mm)

(1) Usage of slicer spacers:

(1) Add 2 pieces slicer spacers under each slicer according to Figure 1, and then tighten the 4 screws as shown in Figure 4, so that the sliced food thickness can be 3mm;
(2) According to Figure 2: add 1 piece of slicer spacer under each slicer knife, and then tighten 4 screws as shown in Figure 4, so that the sliced food thickness can be cut to 2mm;
(3) According to Figure 3: no slicer spacer is added to the bottom of the slicer spacer, and then tighten the 4 screws as shown in Figure 4, the sliced food thickness can be 1mm.

(2) Usage of shredding knife set (3mm): remove the shredding knife set (2mm) from the shredding disc according to Figure 5, replace the shredding knife set (3mm) according to Figure 6, and then tighten 4 screws as shown in Figure 7, the width of the shredded food can be changed from 2mm to 3mm.

Warning!

1. All blades are very sharp, please be careful when disassembling and using, caution your hands!
2. Please do not cut frozen or hard food!

Chapter 4: Maintenance

1. The surface in contact with food should be clean.
2. Before cleaning, the plug should be pulled out and the product should be cooled. Remember that the aluminum alloy housing of the machine cannot be soaked in water, and do not wipe the hole of the micro switch ejector rod and the position of the switch with a wet towel.
3. Do not use steel wool and any chemical or abrasive powder cleaners to clean the product.
4. After use, it must be wiped with a soft and clean cloth.
5. The product should be stored in a cool, dry and clean place, and out of reach of children and pets.
6. Please keep the packaging. When the product is not used for a long time, the packaging can be restored for storage.
7. All blades are very sharp, please be careful when disassembling and cleaning, caution your hands!
8. All detachable parts can be washed directly with water!

Chapter 5: Product Parameters:

Chapter 6: Schematic Diagram

1. Power Supply Cord
2. Rocker Switch
3. Micro Switch
4. Current Plate

Chapter 7: Fault Analysis

power is connected.
2. Check whether the aluminum alloy lip is installed properly.
Stop suddenly| The machine works for a long time or the working environment temperature is too high, which causes the motor temperature to be too high, and the motor thermostat protection stops.| Turn off the power, stop for more than half an hour, wait for the motor to cool down and then restart it.

Remarks: The above are common fault diagnosis and resolution methods. For other faults, please contact after-sales service, do not disassemble and repair by yourself.

Chapter 8: Food contact list

GB4806.9-2016
GB4806.11-2016| Qualified
Slitting Knife| ABS + Stainless Steel| GB4806.1-2016
GB4806.9-2016
GB4806.11-2016| Qualified
Housing| Aluminum Alloy| GB4806.1-2016
GB4806.10-2016| Qualified
The Upper Shell| Aluminum Alloy| GB4806.1-2016
GB4806.10-2016| Qualified
Slicing Blade| SUS420| GB4806.1-2016
GB4806.9-2016| Qualified
Shred Auxiliary Blade| SUS420| GB4806.1-2016
GB4806.9-2016| Qualified
Dicing Blade| SUS420 + Aluminum Alloy| GB4806.1-2016
GB4806.9-2016| Qualified
Diced Knife Holder| SUS304| GB4806.1-2016
GB4806.9-2016| Qualified
Slicer Spacer| SUS304| GB4806.1-2016
GB4806.9-2016| Qualified
The Pin of Shredding Knife Set| SUS304| GB4806.1-2016
GB4806.9-2016| Qualified
Positioning Shaft Sleeve| SUS304| GB4806.1-2016
GB4806.9-2016| Qualified
The Insert of Tighten Handle| SUS304| GB4806.1-2016
GB4806.9-2016| Qualified
Tighten Screws| SUS304| GB4806.1-2016
GB4806.9-2016| Qualified
Motor Shaft| SUS304| GB4806.1-2016
GB4806.9-2016| Qualified
Stainless Steel Screw| SUS304| GB4806.1-2016
GB4806.9-2016| Qualified
M4 Insert Nut| Copper| GB4806.1-2016
GB4806.9-2016| Qualified

Chapter 9: Environmental Checklist

Declaration of Hazardous Substances of Kitchen Machines (Multifunctional Food Processor) Used in This Form
According to the “Marking Requirements for Restricted Use of Hazardous Substances in Electrical and Electronic Products”
The following part of GB/T26572-2011 (also known as China RoHs2.0) lists the hazardous substances and contents that may be contained in this product.
This form is prepared according to the rules of SJ/T11364
O: Indicates that the content of the hazardous substance in all homogeneous materials of the part is within the limit requirement specified in GB/T26572. However, the content of the parts marked with “X” in the above table exceeds that because there is no mature alternative technology in the industry.

Environmental Protection Use Period

The sign marked on the product indicates that the environmental protection use period is 10 years.
The environmental protection use period of electrical and electronic products means that the toxic and harmful substances or elements contained in electrical and electronic products will not leak to the outside or change suddenly, and users of electrical and electronic products will not harm the environment when using the electrical and electronic products. The time limit for causing serious pollution or serious damage to human body and property.

During the environmental protection period, please use this product according to the instruction manual.

Suggestive Explanation of “Regulations on the Administration of Recycling and Disposal of Waste Electrical and Electronic Products”: In order to better care for and protect the earth, when the user no longer needs this product or the product life is over, please abide by the relevant national laws and regulations on the recycling and disposal of waste electronic products, and hand them over to local manufacturers with nationally recognized recycling qualifications for recycling.

Environmental Checklist

According to the “Law on the Administration of the Use of Hazardous Substances in Electrical and Electronic Products” of the People’s Republic of China, list the names and contents of hazardous substances or elements that may be contained in electrical and electronic products in the following form|

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>