Tonnlog V15 Digital Voice Recorder Instruction Manual

**Tonnlog V15 Digital Voice Recorder Instruction Manual

**

Introduction

Key description

Tips: This pictures just for reference, thes pacification of the product is subject to the real object.

1.  Micro-USB port 2
2.  Indicator hole/sound source input hole
3.  Power switch: turn on recording/turnoff to saver ecording

Note: Line control is remote control  accessories, not the machine itself, please look for the mint hepa ckage. If lost, please contact customer service

Product description

*** Dimensions| 0.583.185.33cm0.231.25*2.10 inch (The actual shall prevail)
---|---
Weight| 21g/0.74oz   (The   actual shall prevail)
Battery specifications| 200mAh
Built-in memory| 32GB-64GB
Recording format| WAV
Music format| MP3/WMA/WAV
Support system| Windows/Mac/Android
USB interface| USB 2.0
Headphone output| External stereo
Operating temperature| 20 to 110℉
Recording sampling rate| 48KHZ
Charging current/ voltage| 5V/1A
Charge time| 2.5 hours
Default bit rate| 384 kbps

Indicator light description

Turn on| The   purple  indicator   flashes   oncethen the red indicator flashes 3 times
---|---
During recording| No indicator flashes
Turn off| The purple indicator flashes once
Standby| The blue indicator is always on
Charging| When   charging,   the   red   indicator flashes, when full- charged, the bluelight is always on
Record while charging| No indicator flashes
Low power| The red Indicator flashes quickly forabout      10 seconds      and      then automatically shut down
Earphone playback| Blue indicator flashes
Fast forward / Fast rewind| when playing, long press    /    tofast forward/fast   rewind,   the   blueindicator flashes rapidly

Method of use

One click Record/Save
Record Save
Tips: Recordable distance depends on the level of the sound we record. When the sound is high enough even if the distance recording can be very clear Fast forward/rewind is only possible during playback.

Charge

1. Power OFF(SAVE) before charging.
2.  Charge the recorder by a mobile phone charger. The charging speed will be very slow if use the computer’s USB port to charge.
3. The red light flashes during charging. After 2.5 hours fully charged, the blue light always on.
4. Record while charging: If the charger is plugged in while recording, the recording will end. Please turn on the recording again to continue.
5. Reminder: If the battery is not charged for a long time after it has run out, you may need to re-sync the time of the recorder with the time of your computer
   
   Note: If you do not need to record while charging, do not switch the power [ON] while charging!
   No indicator light in the state of charge recording! If there is no indicator light charging situation, please follow the correct method of charging!

layback/File management

Connect to earphone
!!!Can no longer record when earphones are plugged in.
Plug in headphones, you can pause/play, fast forward and rewind via the in- line controls.
Note : After connecting the earphones, it will turn off automatically when the pause button is pressed without playing for a long time (reboot and play).

Connect to computer
(!!!Power off before connecting) I Can’t record when connected to a computer

Connect to PC by the Micro-USB cable supplied. Find [USB DISK] → [RECORD], select the file you want to play/delete/transfer

Connect to Android phone
Connect to your android phone with the OTG cable/converter adapter (sold separately) to playback /delete recording files Route: [File Management]→ [USB device]→ [RECORD]

Note: As each Android device model is different, we dare not guarantee that all devices can be connected via OTG!)

If PC/Phone connection fails?

1.  Before connecting the recorder
   to a computer/phone, turn off the recorder. When connect, please place the recorder smoothly, do not press any buttons.

2. Please use the original USB cable or a data cable that can be used to transfer data (some data cables can only be used for charging).

3. Restart the computer/phone or recorder

4. If the cable in the package does not connect successfully, please connect with a different cable to rule out cable problems.

5. Android Phone:
   Make sure the OTG function is turned on. [Settings] Search for “OTG or USB”, turn on the OTG function and allow other devices to connect. (As each Android device model is different, you can Google search or ask the phone manufacturer for the exact method to turn on the OTG function)

6. PC :

7.  MAC user: please replace the USB-C adapter

8. Change the computer to change the connection port and try again

9. Check if the USB DISK iden tifier appears on my computer. Click “USB Disk Identifier” in the lower right corner of the desktop [Open Devices and Printers] [Devices] right click [HS USB FlashDisk] [Remove Device] and then connect to the computer.

Settings

SetTime(Windows only)
After connecting to the PC, use the USB device to Click on the [Settime] tool and the date and time will be same with the PC system time Route: [USB DISK」→「Settime」→「SetDigitRe-

Note:

1. The recording files are named after the time they were recorded, so you can clearly see when each file was recorded after synchronising the time.
2. This method of synchronising time can only be used on Windows computers, if you have a MAC computer, please refer to page 12 [5.2.1 Time  stamp(Time)] 10
3. If the [RECSET] file is opened again after [SETTIME] has been used, the recording file name may not be changed correctly.

RECSET.txt Setting (no recommended changes)

1. Power off before connecting the PC
2. [USB DSIK] → [RECSET.txt]
3. MAC users should copy the [RECSET.TXT] file to the MAC desktop and make changes on the MAC desktop, if necessary. After completing the modifications, save the file.
   Then remove the [RECSET] file in the original [USB DISK to the Trash. Copy the new [RECSET] file to the USB DISK.  Scan the QR code below to see the exact steps(PDF
   
   

Time stamp(Time)
The number after [Time] represents the year, month, day, hour, minute and second (Must be 14 digits, no other symbols in between), for example: Time:20220508183030 means 2022-05-08-183030.
You can change the recording file time naming by changing these numbers, note that it must be 14 digits! Windwos users are advised to set the time by SETTIME.

Recording sensitivity(Gain)
(Default: 5)
The number after [Gain] represents the recording sensitivity, the higher the number, the higher the sensitivity. The following numbers can be replaced by any number between 0 and 7, it is recommended to set the sensitivity to 5. (If set to 1, the sensitivity of the recorder is too low and some recordings will

be missed, if set to 7, the sensitivity is too high resulting in capturing very subtle sounds and thus creating noise).
If the recording distance is long, the number can be increased appropriately, but it is recommended to record at close range.
Voice activation(Vor)
(Default: 0)
0: T urn off voice activation
1-5: Turn on voice activation
Turning on voice activation(advice): 1~3
For example: [USB DISK]-[RECSET.TXT]-[Vor:1] -Ctrl+S to Save

Notes:

1. The smaller the number, the higher the decibel level required to activate recording and the more pronounced the voice activation effect, if the value is too large, recording will be activated when the decibel level is very small and may record very little noise.
2.  It is not recommended to turn on voice activation on important occasions as it will pause the recording and may cause important recordings to be missed when the sound is too low or less than around 40 decibels
3. if you can’t record after setting the Vor, Please reset the number after Vor to 0 and press Ctrl+S to save.
4.  Check the [Vor] Settings successfully Vor: 1,Ctrl+S to save, then unplug the recorder and record.
   Test 10 minutes recording, actual recording time may be around 5 minutes.

Test 10 minutes recording, actual recording time may be around 5 minutes. If the recording file name starts with “V”, the Vor

setting has been successfully switchedon. Example: V20200630-013747.WAV

Sound quality(Bit)
(Default: 1)
Note: Cannot be changed
The number after [Bit] corresponds to the bit rate of the recorder, 1-384kbps

Segment record(PART)

( Default: 0)
The number after [PART] represents the length of segment recording, change the number to change the length of segment recording, For example, if you change the number to 120, the recording file is saved every 120 minutes (2 hours), the number can be changed to 0-240, to ensure the continuity of recording, it is recommended to set the number to 0. (Note: If the recording length exceeds 8 hours, the recorder will automatically segment recording, it will form more than one recording file).

!!!The above settings are optimised at the factory. If an error occurs in the settings, please change all parameters to the default parameters.

Q3: How to reduce noise?

. You can refer to the manual, turn on the voice activation function and pause the recording when it is quiet. 2. Place the recorder stably and avoid rubbing it against other objects, such as hands, clothing, etc. 3. Away from sources of noise (e.g. air conditioning, typing, or subtle noise that may be generated by running computers) 4. The recorder should be at least 30cm away from the sound source, otherwise it is likely to produce a bursting sound 5. If the recording environment is very noisy, can not avoid the noise, please understand. Advice: Recording in quiet environment

Q4: Can't listen after connecting earphones?

. Check whether the battery is exhausted and recharge it in time 2. Make sure the earphone has been inserted, make sure the recorder is turned off before inserting the earphone . Make sure there is a recording file in the recorder 4. The sound may be too low, you can increase the volume appropriately 5. The file being played is not supported by the recorder(only supports WAV,MP3 formats) 6. If the recorder does not continue to play for a long time after the pause button is pressed, the recorder will automatically switch off to protect the battery, please turn the recorder on again if you need to play

Q5: Can't fast forward/rewind?

Fast forward/rewind is only possible during playback

06: Why can some 16 GB recorders store 1000 hours of recordings. This

bigger recorder can only store 750 hours of recording?

A: The default bit rate of this recorder is 384Kbps, the higher sound quality is, the larger storage space occupied of course.

: Why is the actual storage space of this recorder not up to the advertised

storage space?

A: All memory manufacturers in the world produce the memory according to 1000 MB = 1 GB, while the computer recognizes the recorder according to 1024 MB = 1 GB. At the same time, the system software also takes up part of the storage space, so the actual capacity is smaller than the nominal capacity. This problem exists in the memory of all electronic products

Q8: I lost my earphone and remote control. Where can I get a new one?

A: Don't worry about it, If your recorder has any problems or lost parts, please contact us in time, we will solve your problem in the first time.

Q9: Does the recorder have a built-in speaker?

A: No, recording files can be played back via headphones, computer or mobile phone (refer to page 7)

Q10: Does it support recording while charging?

A: Yes, please refer to page 6

Q11: How can I deal with a recorder that does not light up when charging or

has not been fully charged for a long time?

A: Charge the recorder in the correct way or replace the charging cable. Please refer to page 6 for the correct charging method

Q12: What's in the package?

1Digital voice recorder 1Data cable 1*Manual

After Sales Service: Please rest assured of product quality, we have done strict factory quality inspection. If the above problem cannot be solved, please send a message to the seller in the order history and we will solve the product problem in time: Order history – Seller – Ask a question

E-Manual(5 language)

English

Deutsch

Français

Italiano

Español

Cautions

1. Children are forbidden to play the recorder alone, and do not fall and collide with hard objects, otherwise it may cause data loss or other hardware damage of the recorder.
2. Do not clean the recorder with chemical reagents or cleaning reagents, which will damage the shell of the recorder and corrode it.
3. t is recommended not to use this recorder when driving a motor vehicle or riding a bicycle. Please ensure driving safety.
4. Please back up the important files in the recorder in time. No one can guarantee the absolute security of the data. If data loss occurs, the files will be difficult to recover.
5. It is forbidden to use overload charger or the charging cable is squeezed by heavy objects for a long time, keep away from combustibles when charging, in order to avoid fire.
6. It is forbidden to pull out the charger with wet hands to prevent electric shock. 23

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>