HINKLEY 5041 LED Flush Mount Instruction Manual

: June 15, 2024
: HINKLEY

Table of Contents

HINKLEY 5041 LED Flush Mount
Product Information
Electrical Wiring Instructions
FAQ
Mounting Instructions
Assembly Instructions
wiring instructions
grounding instructions
CONTACT
Read User Manual Online (PDF format)
Download This Manual (PDF format)

HINKLEY 5041 LED Flush Mount

HINKLEY-5041-LED-Flush-Mount-product

Product Information

Specifications

Brand: HINKLEY
Item Number: 5041

Mounting Instructions

Find a clear area in which you can work.
Unpack the fixture and glass from the carton.
Carefully review instructions before assembly.
Insert screws (1) through holes (M) in the mounting bracket and canopy (3).
Secure the fixture to the ceiling by threading ball knobs (4) onto the end of screws (1) and tightening them.

Electrical Wiring Instructions

SAFETY WARNING: Read wiring and grounding instructions (I.S. 18) and any additional directions. Turn off the power supply during installation. If new wiring is required, consult a qualified electrician or local authorities for code requirements.

Make electrical connections from the supply wire to the fixture lead wires.
Refer to the instruction sheet (I.S. 18) and follow all instructions to make all necessary wiring connections.
Refer back to this sheet to complete the installation of this fixture.

FAQ

Q: What should I do before starting the installation?
A: Find a clear area in which you can work, unpack the fixture and glass from the carton, and carefully review the instructions before assembly.
Q: How do I mount the fixture to the ceiling?
A: Insert the screws (1) through the holes (M) in the mounting bracket and canopy (3). Secure the fixture to the ceiling by threading the ball knobs (4) onto the end of the screws (1) and tightening them.
Q: Are there any safety precautions I should take during the installation?
A: Yes, it is important to read the wiring and grounding instructions (I.S. 18) and any additional directions. Turn off the power supply during installation. If new wiring is required, consult a qualified electrician or local authorities for code requirements.

Mounting Instructions

start here

Find a clear area in which you can work.
Unpack the fixture and glass from the carton.
Carefully review instructions before assembly.

Shut off the electrical current before starting. If the fixture you are replacing is turned on and off by a wall switch, simply turn the switch off. If not, remove the appropriate fuse (or open the circuit breakers) until the fixture is dead.

DO NOT restore current – either by fuse, breaker or switch – until the new fixture is completely wired and in place.

Drawing 1 – Mounting Detail

HINKLEY-5041-LED-Flush-Mount-fig-1

STEP 1

Thread two long 8-32 screws (1) into the mounting strap (2).NOTE: The two screws must be threaded into holes that match the mounting hole spacing (M) on the canopy (3) – see Drawing 1.
Attach the mounting strap (2) to the junction box with two 8-32 screws (5) [NOT PROVIDED].
The fixture you have purchased is supplied with an inspection cable on the canopy. With assistance take the canopy and lift it, and using the hook on the end of the inspection cable, attached to the inside of the canopy (3), hook it into the mounting strap. Now slowly release the fixture until it is safely hanging from the inspection cable – see DETAIL 2. It is still recommended that an assistant be used to support fixtures during this process.
Make electrical connections following the instruction sheet [IS18] provided.
To install the fixture, first, lift assembled fixture up to the ceiling and slip the screws.

(1) in mounting bracket through holes (M) in the canopy (3). Secure the fixture to the ceiling by threading ball knobs (4) onto the end of screws (1) and tightening.

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.
Make electrical connections from supply wire to fixture lead wires. Refer to the instruction sheet (I.S. 18) and follow all instructions to make all necessary wiring connections. Then refer back to this sheet to complete the installation of this fixture.

Assembly Instructions

start here

Find a clear area in which you can work.
Unpack the fixture and glass from the carton.
Carefully review instructions before assembly.

DRAWING 2 – INSTALLATION

Lamp fixture using appropriate medium base bulbs (6)
Secure nipple (3) and hex nut (9) to coupler (1)
Slide tube (2) and end cap (4) over nipple (3)
Place washer (7) and diffuser (8) onto nipple (3)
Place plastic washer (5), metal washer (11) and hex nut (12) underneath diffuser
Secure diffuser using final (10)

wiring grounding instructions

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (IS 18) AND ANY ADDITIONAL DIRECTIONS.
TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS

wiring instructions

Indoor Fixtures

Connect positive supply wire (A) (typically black or the smooth, unmarked side of the two-conductor cord) to positive fixture lead (B) with an appropriately sized twist on the connector – see Drawings 1 or 2.
Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).
Please refer to the grounding instructions below to complete all electrical connections.

Drawing 1 – Flush Mount

Outdoor Fixtures

Connect positive supply wire (A) (typically black or the smooth unmarked side of the two-conductor cord) to positive fixture lead (B) with an appropriately sized twist on the connector — see Drawings 2 or 3.
Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).
Cover the open end of connectors with silicone sealant to form a watertight seal.
- If installing a wall mount fixture, use caulk to seal gaps between the fixture mounting plate (backplate) and the wall. This will help prevent water from entering the outlet box. If the wall surface is lap siding, use caulk and a fixture mounting platform specially.
Please refer to the grounding instructions below to complete all electrical connections.

Drawing 2 – Chain Hung

grounding instructions

Drawing 3 – Post-Mount

Flush Mount Fixtures
For positive grounding in a 3-wire electrical system, fasten the fixture ground wire (E) (typically copper or green plastic coated) to the fixture mounting strap (M) with the ground screw (S) – see Drawing 1. Note: On straps for screw-supported fixtures, first install the two mounting screws in the strap. Any remaining tapped hole may be used for the ground screw.
Chain Hung Fixtures
Loop fixture ground wire (E) (typically copper or green plastic coated) under the head of the ground screw (S) on the fixture mounting strap (M) and connect to the loose end of the fixture ground wire directly to the ground wire of the building system with appropriately sized twist-on connectors – see Drawing 2.
Post-Mount Fixtures
Connect fixture ground wire (E) (typically copper or green plastic coated) to the power supply ground with an appropriately sized twist-on connector inside the post. Cover the open end of the connector with silicone sealant to form a watertight seal – see Drawing 3.