MARTEC MNDC183WN Norfolk Aero DC Smart Series Ceiling Fan Installation Guide

June 15, 2024
martec

MARTEC MNDC183WN Norfolk Aero DC Smart Series Ceiling Fan

MARTEC-MNDC183WN-Norfolk-Aero-DC-Smart-Series-Ceiling-Fan-
product

Product Information

Specifications

  • * Models Parameters (Fan Only)
    • MNDC183WN – 1765mm 3Blade DC WiFi Ceiling Fan, Matt White/Natural
    • MNDC183WW – 1765mm 3Blade DC WiFi Ceiling Fan, Matt White/Whitewash
    • MNDC183MW – 1765mm 3Blade DC WiFi Ceiling Fan, Matt Black/Walnut
    • MNDC223WN – 2175mm 3Blade DC WiFi Ceiling Fan, Matt White/Natural
    • MNDC223WW – 2175mm 3Blade DC WiFi Ceiling Fan, Matt White/Whitewash
    • MNDC223MW – 2175mm 3Blade DC WiFi Ceiling Fan, Matt Black/Walnut

Part List

  • * 1x Motor assembly
    • 1x Mounting bracket
    • 1x Downrod
    • 1x Instruction manual
    • 1x Remote & Receiver
    • 1x Canopy
    • 1x Screw kit
    • 3x Blades
    • 1x Bottom plate
    • 1x Coupling cover
    • 1x Decorative ring
    • 1x Blade fixing metal plate

Important Safeguards

  • * Means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.
    • The replacement of parts of the safety suspension system device shall be performed by the manufacturer, its service agent, or suitably qualified persons.
    • The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person.
    • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
    • Children should be supervised to ensure that they do not play with the appliance.
    • The fixing means for attachment to the ceiling such as hooks or other devices shall be fixed with sufficient strength to withstand 4 times the weight of the ceiling fan.
    • The mounting of the suspension system shall be performed by the manufacturer, its service agent, or suitably qualified persons.
    • The fan is to be installed so that the blades are more than 2.1m above the floor.
    • If unusual oscillating movement is observed, immediately stop using the ceiling fan and contact the manufacturer, its service agent, or suitably qualified persons.

Product Usage Instructions

How to Assemble

  1. Secure the bracket to the ceiling by using screws provided. Ensure screws are tightened on the bracket. Refer to Figure 1.
  2. Wire to main as illustrated. Refer to Figure 2.

How to Install Blades

  1. Install the blades and blade fixing metal plate to the motor with screws provided, first tightening the screws by 80%.
  2. Repeat this procedure until all the blades are installed, and then tighten the screws fully. Refer to Figure 3.

Note : Ensure the blades do not get damaged or bent during the installation process while the fan may be on the ground. This will affect the performance and balance of the fan and is NOT covered under warranty.

How to Install
Refer to Figure 4 for installation instructions.

FAQ

Q: Who should perform the installation?
A: The installation MUST be carried out by a qualified and licensed electrician.

Norfolk Aero DC Smart Series Installation Guide

  • Thanks for choosing our Norfolk Aero DC Smart Series ceiling fan.
  • We strongly recommend that you read this manual carefully before installation.

Models Parameters (Fan Only)

  • MNDC183WN 1765mm 3 Blade DC WiFi Ceiling Fan Matt White/Natural
  • MNDC183WW 1765mm 3 Blade DC WiFi Ceiling Fan Matt White/Whitewash
  • MNDC183MW 1765mm 3 Blade DC WiFi Ceiling Fan Matt Black/Walnut
  • MNDC223WN 2175mm 3 Blade DC WiFi Ceiling Fan Matt White/Natural
  • MNDC223WW 2175mm 3 Blade DC WiFi Ceiling Fan Matt White/Whitewash
  • MNDC223MW 2175mm 3 Blade DC WiFi Ceiling Fan Matt Black/Walnut

Part List

  • Qty 1 x Motor assembly
  • Qty 1 x Mounting bracket
  • Qty 1 x Downrod
  • Qty 1x Instruction manual
  • Qty 1 x Remote & Receiver
  • Qty 1 x Canopy
  • Qty 1 x Screw kit
  • Qty 3x Blades
  • Qty 1x Bottom plate
  • Qty 1x Coupling cover
  • Qty 1x Decorative ring
  • Qty 1xBlade fixing metal plate

MARTEC-MNDC183WN-Norfolk-Aero-DC-Smart-Series-Ceiling-Fan-
\(1\)

Application

MARTEC-MNDC183WN-Norfolk-Aero-DC-Smart-Series-Ceiling-Fan-
\(2\)

WARNING Installation MUST carry out by a qualified and licensed electrician.

IMPORTANT SAFEGUARDS

  • Means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.
  • The replacement of parts of the safety suspension system device shall be performed by the manufacturer, its service agent or suitably qualified persons.
  • The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person.
  • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
  • Children should be supervised to ensure that they do not play with the appliance.
    • the fixing means for attachment to the ceiling such as hooks or other devices shall be fixed with a sufficient strength to withstand 4 times the weight of the ceiling fan;
    • that the mounting of the suspension system shall be performed by the manufacturer, its service agent or suitably qualified persons;
    • that the fan is to be installed so that the blades are more than 2,1m above the floor.

WARNING: If unusual oscillating movement is observed, immediately stop using the ceiling fan and contact the manufacturer, its service agent or suitably qualified persons.

How to Assemble

MARTEC-MNDC183WN-Norfolk-Aero-DC-Smart-Series-Ceiling-Fan-
\(3\)

How to Install Blades MARTEC-MNDC183WN-Norfolk-Aero-DC-Smart-Series-
Ceiling-Fan- \(4\)

  • Install the blades and blade fixing metal plate to the motor with screws provided, first tightening the screws by 80%, Repeat this procedure until all the blades are installed, and then tighten the screws fully.

  • NB : Ensure the blades do not get damaged or bent during the installation process while the fan maybe on the ground, this will affect the performance and balance of the fan and this is NOT covered under warranty.
    MARTEC-MNDC183WN-Norfolk-Aero-DC-Smart-Series-Ceiling-Fan-
\(5\)

  • Remove cotter-pin and cross-pin from the bottom of the downrod.

  • At the top of the downrod loosen the two set screws and remove ball pin. NB: Ensure all pieces are carefully put aside. MARTEC-MNDC183WN-Norfolk-Aero-DC-Smart-Series-Ceiling-Fan- \(6\)

  • Assemble rest parts of the fan as illustrated. Feed the main motor wire plug up through the inside of the downrod. MARTEC-MNDC183WN-Norfolk-Aero-DC-Smart-Series-Ceiling-Fan- \(7\) MARTEC-MNDC183WN-Norfolk-Aero-DC-Smart-Series-Ceiling-Fan- \(8\)

  • Gently push the cross-pin through the holes aligned with the base of the downrod holder and downrod. Insert cotter pin into cross pin and secure downrod with two set screws.

  • NB : DO NOT force the cross-pin. Gently wiggle and rotate it until it glides through both holes. MARTEC-MNDC183WN-Norfolk-Aero-DC-Smart-Series-Ceiling-Fan- \(9\)

  • Place fan into mounting bracket and align ball joint slot with mounting bracket as illustrated. MARTEC-MNDC183WN-Norfolk-Aero-DC-Smart-Series-Ceiling-Fan- \(10\)

  • Wire up the receiver with quick connectors and insert intoWire up the receiver with quick connectors and insert into the mounting bracket. Mak the mounting bracket. Make sure the antenna wire has beene sure the antenna wire has been safely folded inside the canopy cover before final assembly. (DO NOT cut the antenna wire)

Important Reminders
Receiver must be correctly installed in the mounting bracket When the transmitter cannot control the receiver, please check

  1. has sufficient battery in the transmitter
  2. any existence of similar remote controlled products nearby that cause interference

Replace battery if getting low as this will affect sensitivity of the transmitter

  • Take the battery out from the transmitter when leaving used for a long time to avoid battery leaks Isolation switch MUST be connected in the line
  • After wiring is completed attach the canopy to the mounting bracket by pushing upwards and twisting anti-clockwise. Tighten screws and ensure canopy is not touching the ball joint. And then attach the decorative ring to the canopy as illustrated. MARTEC-MNDC183WN-Norfolk-Aero-DC-Smart-Series-Ceiling-Fan- \(12\)
  • Twist bottom plate on to motor shaft thread.

WOBBLE

  • Ceiling fans are designed to move during operation because they are not generally rigidly mounted
  • Movement of a couple of centimeters is acceptable for safe operation.
  • Balancing kits included should be used to adjust the balancing when first installed.

Complete

MARTEC-MNDC183WN-Norfolk-Aero-DC-Smart-Series-Ceiling-Fan-
\(13\)

Wire Connections MARTEC-MNDC183WN-Norfolk-Aero-DC-Smart-Series-Ceiling-
Fan- \(14\)

6* Year Warranty

WARNING

  • Installation of fans MUST follow SAA standards and meet local authority regulations.
  • Installation MUST be carried out by a qualified and licensed electrician.
  • Fan and light MUST be earthed.
  • Bracket MUST be firmly attached to a flat solid structure or timber frame.
  • DO NOT mix blades from one model to another, all blades MUST be replaced if damaged.
  • The warranty is VOID if product is not installed according to this installation guide.

Smart Life matching process, please follow the steps

  1. Download the “Smart Life” APP on your smart devices by scanning the QR code below with camera.

  2. Turn on WiFi and Bluetooth on your smart devices. Ensu-, re it’s connected to a 2.4GHZ WiFi.

  3. Open the APP, follow the steps to register new user ace- I1 cunt or login existing account.

  4. MARTEC-MNDC183WN-Norfolk-Aero-DC-Smart-Series-Ceiling-Fan- \(16\)Follow instructions in main manual (steps can also be found on the back of the remote) to put the fan into WiFi pairing mode. If the operation is successful, go to step fi. If the fan has previously been paired or you can’t get it to work, please go to step 5 to RESET the fan.

  5. RESET the fan. This step is NOT necessary if the fan ha?
    successfully entered WiFi pairing mode in the last step, if : not, try to RESET the fan turn on the fan, power off after : 10 seconds, power on again after 15 seconds, long press :
    “Fan Stop” for 5 seconds, if “beep beep” are heard, the 1I reset is successful. If “beep beep” is not heard, the reset is
    failed, please repeat this step. MARTEC-MNDC183WN-Norfolk-Aero-DC-Smart-
Series-Ceiling-Fan- \(17\)

  6. Once the fan has entered WiFi pairing mode, open the | APP again on the smart device. Click “Add Device” in the middle or the “+” on the top right of the screen. MARTEC-MNDC183WN-Norfolk-Aero-DC-Smart-Series-Ceiling-Fan- \(18\)

  7. The auto scan should begin automatically, and the fan should show up at the top of screen within a few seconds.
    Note : If the fan is not showing up, you can add it manually by clicking and navigate to >Add Manually >Small Home Appliance > Fan

  8. Follow instructions in the APP to finish the set up. MARTEC-MNDC183WN-Norfolk-Aero-DC-Smart-Series-Ceiling-Fan- \(19\)

WiFi / Remote Control Pairing

MARTEC-MNDC183WN-Norfolk-Aero-DC-Smart-Series-Ceiling-Fan-
\(22\)

Fan only model Pairing the remote control

  1. Turn on the ceiling fan.
  2. Within the first 20 seconds, continue pressing the button until you hear a “beep” sound. ie. It is paired.

If you don’t hear a “beep” sound, repeat step 1 and step 2 again.

Entering WiFi Pairing mode

  1. Turn on the power.
  2. Within the first 20 seconds, press and hold the ” ” button until a “beep” is heard. •
  3. Continue step connect on your smart devices to complete the pairing.

If you don’t hear a ”beep” sound, repeat the above steps.
FAN OFF : to switch off the fan.

  • SLEEP MODE Turn on the fan at an extra lower speed to create a general breeze.
  • SPEED BUTTON: 1 = lowest speed. 6 = highest speed.
  • NATURAL WIND MODE : designed for the elderly and children. 1-6 speed changes randomly to feel the breeze.
  • FORWORD AND REVERSAL ( ): summer/winter reverse mode.
  • TIMER 1H/4H/8H : preset timer for fan and light to stop automatically. ie. if timer set at 1 H and then press 4H, fan will stop at 4H. Setting default to last press.
  • WIFI BUTTON :Follow the instructions and press and hold for 20 seconds to enier wifi matching mode.

Fan LED Light Model Pairing the remote control

Turn on the ceiling fan.
Within the first 20 seconds, continue pressing the button until you hear a “beep” sound. ie. It is paired.

If you don’t hear a “beep” sound, repeat step 1 and step 2 again.

Entering WiFi Pairing mode

  1. Turn on the power.
  2. Within the first 20 seconds, pre$s and hold the ” · ” button until a “beep”  is heard.
  3. Continue step connect on your smart devices to complete the pairing.

If you don’t hear a “beep” sound, repeat the above steps.

  • FAN OFF ; to .witch off the fan.
  • SLEEP MODE : Turn on the fan at an extra lower speed to create a general breeze.
  • SPEED BUTTON: 1 = lowest speed. 6 = highest speed.
  • NATURAL WIND MODE : designed for the elderly and children. 1-6 speed changes randomly to feel the breeze.
  • FORWORD AND REVERSAL : summer/Winter reverse mode.
  • TIMER 1H/4H/8H: preset timer for fan and light to stop automatically. ie. if timer set at 1 H and then press 4H, fan will stop at 4H. Setting default to last press.
  • LIGHT ON/ OFF- : to switch off the light.
  • CCT : warm white (2700K) / netural white (4000K) / cool white (6500K)
  • LED- LED+ : minus”-” = reduces brightness  plus “+”= increases brightness

*6 Year Warranty**
Visit our website for details https://www.martecaustralia.eom.au/wp- content/uploads/2023/05/Warranty-5tatement_Cooling.pdf

WARNING

  • Installation of fans MUST follow SAA standards and meet local authority regulations.
  • Installation MUST be carried out by a qualified and licensed electrician.
  • Fan and light MUST be earthed.
  • Bracket MUST be firmly attached to a flat solid structure or timber frame.
  • DO NOT mix blades from one model to another, all blades MUST be replaced if damaged. The warranty is VOID if product is not installed according to this installation guide.
  • E: sales@martecltd.com.au
  • I P: 02 8778 7500
  • www.martecaustralia.com.au

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

martec User Manuals

Related Manuals