ZAHEES Smart Bidet Toilet for Bathroom with Remote Control User Manual

ZAHEES Smart Bidet Toilet for Bathroom with Remote Control

INSTALLATION INSTRUCTION

Preparation before installation

Tools prepared by user: Monkey Spanner, Teflon Tape, Glass Cement Gun, Glass Cement, Tapeline.

Parts included in the package: flange ring, water shutoff valve (Please use the parts included in the package, otherwise may cause product malfunction).

Installation method

1. Install the water supply hose (as the following picture).
2. Install flange on the ceramic base sewage outlet. Then align the ceramic which equipped with flange to the water drain pipe
3. Install the ceramic correctly to the ground, and use glass cement gun to fix. The solidification time of the glass cement is about 24 hours.
4. Install the shutoff valve (Before installing appliances, be sure to completely wash out any dirt, sand, etc. from inside the water supply pipe)
5. Connect water supply hose with the shutoff valve.
6. Leakage protection plug should be well connected on the wall power socket.
7. Please make sure there is no water leakage in any part of the connection. The power supply function well and the glass cement totally solidification. Then open the shutoff valve and the power button to start using this product.
   Notes: Please make sure product is installed by the professionals. And carefully check if every part is well installed. Only the water pipes of DN15 approved with valid Watermark can be used following local plumbing code.
   

INSTALLATION AND CARE GUIDE

Preparation For the Parts Time Use

Install the remote control battery

Step1: Remove the remote control from the hanger
Step2: Open the battery cover and insert two batteries
Step3: Mount the remote control in the hanger, make sure there 1s no article cover on the remote control.

Notes: Use dry cell, alkaline batteries. Follow the instructions below to prevent the batteries from rupturing or leaking fluid.

1. When replacing the batteries, use new batteries of the same brand.
2. If you will not be using the remote control for a long time, remove the batteries.
3. Do not use rechargeable batteries.
4. Resetting the smart toilet after change the batteries.

Turn on the power

Insert the power plug into the socket, and make sure the power indicator lamp on the power plug turns on.

Open the shutoff valve

Fully open the water shutoff valve.

Make sure the indicator lamp lighting

1. Make sure the toilet power indicator lamp is on, if not, press the button on the leakage protection plug to turn the power on.
2. Make sure the water temperature indicator lamp is on, if not, press the remote control ” WATER ” button.
3. Make sure the seat temperature indicator lamp is on, if not, press the remote contra ” SEAT ” button.

Maintenance and Cleaning

To prevent product damage, please do as following:

1. Always test your cleaning solution on an inconspicuous area before applying to the entire surface

2. Wipe surfaces clean and rinse completely with water immediately after applying cleaner. Rinse and dry any over spray that lands on nearby surfaces.

3. Do not allow cleaners to soak on surfaces.

4. Use a soft, dampened sponge or cloth. Never use an abrasive material such as a brush or scouring pad to clean surfaces.
   Clean the filter(When the flushing system doesn’t function well)

5. Close water shutoff valve to stop the water supply.

6. Remove the filterby coin.

7. Clean the filter:
   To clean the filter by running water after disassemble it.
   To remove any residue by toothbrush.

8. Install the filter back:
   Tightly assemble the filter, and open the water shutoff valve to check if any leakage.

9. Open the water shutoff valve to work.
   
   

Battery Installation

Battreplery a cement method (only for external battery box toilet bowl)

1. Taking out the battery box and install it to the back of the ceramic
   

2. And find the connector of the battery box and connect the line
   
   Notes: If the place between the ceramic and wall too small to change the battery after installed, you can choose the convenient place to put the battery box. The battery box is waterproof design.
   Note: The draft diagram is only used for refer, and the specific appearance 1s based on the physical object.

Maintenance and Cleaning

• Maintenance Nozzle clean

For the Side Control Knob Version:

When the product is standby, turn and hold the side control knob to female wash for 3 seconds until the beeps to activate cleaning wand coming out. Then use a toothbrush to clean the nozzle.

For the Side Control Panel Version:

When the product is standby, press and hold the female wash button for 3 seconds until the beeps to activate cleaning wand coming out. Then use a toothbrush to clean the nozzle.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>