Shaper SY1-CC1 Digital Caliper User Manual
- June 15, 2024
- Shaper
Table of Contents
Shaper SY1-CC1 Digital Caliper
Safety and Regulatory Information
WARNING
- INGESTION HAZARD: This product contains a button cell or coin battery.
- DEATH or serious injury can occur if ingested.
- A swallowed button cell or coin battery can cause Internal Chemical Burns in as little as 2 hours.
- KEEP new and used batteries OUT OF REACH OF CHILDREN.
- Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body.
- Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children. Do NOT dispose of batteries in household trash or incinerate them.
- Even used batteries may cause severe injury or death.
- Call a local poison control center for treatment information.
Battery type: CR2032
- Nominal voltage: 3V
- Temperature rating: 15C – 45C
- Ensure the batteries are installed correctly according to polarity(+ and-).
- Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children.
- Do not mix old and new batteries, different brands, or types of batteries, such as alkaline, carbon-zinc, or rechargeable batteries.
- Remove and immediately discard batteries from equipment not used for an extended period of time.
- Non-rechargeable batteries are not to be recharged.
- Do not force discharge, recharge, disassemble, heat above the manufacturer’s specified temperature rating, or incinerate. Doing so may result in injury due to venting, leakage or explosion resulting in chemical burns.
FCC Compliance Statement
FCC ID: 2AY WN-SY1- CC1
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: this device may not cause harmful interference,
and this device must accept any interference received, including interference
that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF warning for Portable devices:
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
EU Declaration of Conformity
Shaper Tools, Inc. hereby declares that the SY1-CC1 Shaper Connected Caliper is compliant with:
-
2014/35/EU – Low-Voltage Directive (LVD)
-
2014/53/EU – Radio Equipment Directive (RED)
-
2015/863/EU – RoHS 3
-
2012/19/EU – WEEE
-
The complete declaration of conformity is available at: shapertools.com/compliance-sy1-cc1
-
Represented in the UK, by Authorised Rep. Compliance Ltd. ARC House, LA2 0DT, UK
-
Imported into the EU by Shaper Tools GmbH, Wertstr. 20, 73240 Wendlingen, Germany
Environment
For information about how to properly recycle this product, and to learn about Shaper’s commitment to environmentally conscious design and manufacturing, visit shapertools.com/environment. SHAPER ORIGIN, SHAPERHUB, SHAPER & Design and Design Only (Circle & Triangle Logo) are trademarks of Shaper Tools, Inc., registered in the United States and/or other jurisdictions. All rights reserved. shapertools.com Shaper Tools, Inc. 724 Brannan St. San Francisco, CA 94103, USA The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Shaper Tools, Inc. is under license. Other trademarks and trade names are those of their respective owners.