CISCO Catalyst IE3x00 Rugged Series IE Switches User Guide

: June 15, 2024
: Cisco

CISCO Catalyst IE3x00 Rugged Series IE Switches

Product Information

Specifications

Protocol: Hot Standby Router Protocol (HSRP)
Function: Provides routing redundancy for routing IP traffic without being dependent on the availability of any single router
Supported Router Interfaces: Routed ports and switch virtual interfaces (SVIs)
Virtual MAC Address: Shared among router interfaces in a group of router interfaces running HSRP
IP Addresses: n + 1 IP and MAC addresses assigned for n routers running HSRP
HSRP Versions: HSRPv1 and HSRPv2
Multiple HSRP (MHSRP): Allows load sharing between two or more HSRP groups

Product Usage Instructions

Section 1: HSRP Overview

The Hot Standby Router Protocol (HSRP) provides routing redundancy for routing IP traffic without being dependent on the availability of any single router. Routers in an HSRP group can be any router interface that supports HSRP, including routed ports and switch virtual interfaces (SVIs).

Section 2: Configuring HSRP

To configure HSRP, follow these steps:

Specify a group number for each Hot Standby command group you configure for an interface.
Configure an active router and a standby router for each interface.
Configure multiple Hot Standby groups among switches and switch stacks operating in Layer 3 to make use of redundant routers.

Refer to Figure 1: Typical HSRP Configuration for a visual representation of the HSRP configuration.

Section 3: HSRP Versions

HSRP supports two versions: HSRPv1 and HSRPv2.

HSRPv1:

Routers running HSRPv1 use a virtual MAC address and cannot identify the physical router that sent a hello packet.

HSRPv2:

Routers running HSRPv2 use a different packet format with a 6-byte identifier field containing the MAC address of the physical router that sent the packet.
If an interface running HSRPv1 receives an HSRPv2 packet, the type field is ignored.

Section 4: Multiple HSRP (MHSRP)

The switch supports Multiple HSRP (MHSRP), which allows load sharing between two or more HSRP groups. You can configure MHSRP to achieve load balancing and use multiple standby groups and paths from a host network to a server network. To enable preemption and restore load sharing after a router failure, enter the standby preempt interface configuration command on the HSRP interfaces.

Refer to Figure 2: MHSRP Load Sharing for a visual representation of MHSRP load sharing.

Section 5: HSRP and Switch Stacks

In switch stacks, HSRP hello messages are generated by the stack master. If an HSRP-active stack master fails, there might be a flap in the HSRP active state. This is because HSRP hello messages are not generated while a new stack master is elected and initialized, and the standby router might become active after the stack master fails.

FAQ

Q: What is HSRP?

A: HSRP stands for Hot Standby Router Protocol. It provides routing redundancy for routing IP traffic without being dependent on the availability of any single router.

Q: Which router interfaces support HSRP?

A: Routers in an HSRP group can be any router interface that supports HSRP, including routed ports and switch virtual interfaces (SVIs).

Q: How many IP and MAC addresses are assigned for routers running HSRP?

A: For n routers running HSRP, there are n + 1 IP and MAC addresses assigned.

Q: What are the differences between HSRPv1 and HSRPv2?

A: HSRPv1 uses a virtual MAC address and cannot identify the physical router that sent a hello packet. HSRPv2 uses a packet format with a 6-byte identifier field containing the MAC address of the physical router that sent the packet.

Q: What is Multiple HSRP (MHSRP) used for?

A: MHSRP allows load sharing between two or more HSRP groups and enables load balancing and redundancy between a host network and a server network.

Configuring HSRP

This chapter describes how to use Hot Standby Router Protocol (HSRP) to provide routing redundancy for routing IP traffic without being dependent on the availability of any single router.

Configuring HSRP

This chapter describes how to use Hot Standby Router Protocol (HSRP) to provide routing redundancy for routing IP traffic without being dependent on the availability of any single router.

Information About Configuring HSRP

HSRP Overview

HSRP is Cisco’s standard method of providing high network availability by providing first-hop redundancy for IP hosts on an IEEE 802 LAN configured with a default gateway IP address. HSRP routes IP traffic without relying on the availability of any single router. It enables a set of router interfaces to work together to present the appearance of a single virtual router or default gateway to the hosts on a LAN. When HSRP is configured on a network or segment, it provides a virtual Media Access Control (MAC) address and an IP address that is shared among a group of configured routers. HSRP allows two or more HSRP-configured routers to use the MAC address and IP network address of a virtual router.
The virtual router does not exist; it represents the common target for routers that are configured to provide backup to each other. One of the routers is selected to be the active router and another to be the standby router, which assumes control of the group MAC address and IP address should the designated active router fail.

Note

Routers in an HSRP group can be any router interface that supports HSRP, including routed ports and switch virtual interfaces (SVIs).
HSRP provides high network availability by providing redundancy for IP traffic from hosts on networks. In a group of router interfaces, the active router is the router of choice for routing packets; the standby router is the router that takes over the routing duties when an active router fails or when preset conditions are met.
HSRP is useful for hosts that do not support a router discovery protocol and cannot switch to a new router when their selected router reloads or loses power. When HSRP is configured on a network segment, it provides a virtual MAC address and an IP address that is shared among router interfaces in a group of router interfaces running HSRP. The router selected by the protocol to be the active router receives and routes packets destined for the group’s MAC address. For n routers running HSRP, there are n +1 IP and MAC addresses assigned.
HSRP detects when the designated active router fails, and a selected standby router assumes control of the Hot Standby group’s MAC and IP addresses. A new standby router is also selected at that time. Devices running HSRP send and receive multicast UDP-based hello packets to detect router failure and to designate active and standby routers. When HSRP is configured on an interface, Internet Control Message Protocol (ICMP) redirect messages are automatically enabled for the interface.
You can configure multiple Hot Standby groups among switches and switch stacks that are operating in Layer 3 to make more use of the redundant routers.
To do so, specify a group number for each Hot Standby command group you configure for an interface. For example, you might configure an interface on switch 1 as an active router and one on switch 2 as a standby router and also configure another interface on switch 2 as an active router with another interface on switch 1 as its standby router.
The following figure shows a segment of a network configured for HSRP. Each router is configured with the MAC address and IP network address of the virtual router. Instead of configuring hosts on the network with the IP address of Router A, you configure them with the IP address of the virtual router as their default router. When Host C sends packets to Host B, it sends them to the MAC address of the virtual router. If for any reason, Router A stops transferring packets, Router B responds to the virtual IP address and virtual MAC address and becomes the active router, assuming the active router duties. Host C continues to use the IP address of the virtual router to address packets destined for Host B, which Router B now receives and sends to Host B. Until Router A resumes operation, HSRP allows Router B to provide uninterrupted service to users on Host C’s segment that need to communicate with users on Host B’s segment and also continues to perform its normal function of handling packets between the Host A segment and Host B.

HSRP Versions

The switch supports these HSRP versions:

HSRPv1- Version 1 of the HSRP, the default version of HSRP. It has these features:
The HSRP group number can be from 0 to 255.
HSRPv1 uses the multicast address 224.0.0.2 to send hello packets, which can conflict with Cisco Group Management Protocol (CGMP) leave processing. You cannot enable HSRPv1 and CGMP at the same time; they are mutually exclusive.
HSRPv2- Version 2 of the HSRP has these features:
HSRPv2 uses the multicast address 224.0.0.102 to send hello packets. HSRPv2 and CGMP leave processing are no longer mutually exclusive, and both can be enabled at the same time.
HSRPv2 has a different packet format than HRSPv1.
A switch running HSRPv1 cannot identify the physical router that sent a hello packet because the source MAC address of the router is the virtual MAC address.
HSRPv2 has a different packet format than HSRPv1. An HSRPv2 packet uses the type-length-value (TLV) format and has a 6-byte identifier field with the MAC address of the physical router that sent the packet.
If an interface running HSRPv1 gets an HSRPv2 packet, the type field is ignored.

Multiple HSRP

The switch supports Multiple HSRP (MHSRP), an extension of HSRP that allows load sharing between two or more HSRP groups. You can configure MHSRP to achieve load-balancing and to use two or more standby groups (and paths) from a host network to a server network.
In the figure below, half the clients are configured for Router A, and half the clients are configured for Router B. Together, the configuration for Routers A and B establishes two HSRP groups. For Group 1, Router A is the default active router because it has the assigned highest priority, and Router B is the standby router. For Group 2, Router B is the default active router because it has the assigned highest priority, and Router A is the standby router. During normal operation, the two routers share the IP traffic load. When either router becomes unavailable, the other router becomes active and assumes the packet-transfer functions of the router that is unavailable.

Note

For MHSRP, you need to enter the standby preempt interface configuration command on the HSRP interfaces so that if a router fails and then comes back up, preemption restores load sharing.

HSRP and Switch Stacks

HSRP and Switch Stacks

HSRP hello messages are generated by the stack master. If an HSRP-active stack master fails, a flap in the HSRP active state might occur. This is because HSRP hello messages are not generated while a new stack master is elected and initialized, and the standby router might become active after the stack master fails.

Configuring HSRP for IPv6

Switches running support the Hot Standby Router Protocol (HSRP) for IPv6. HSRP provides routing redundancy for routing IPv6 traffic not dependent on the availability of any single router.
IPv6 hosts learn of available routers through IPv6 neighbor discovery router advertisement messages. These messages are multicast periodically or are solicited by hosts.
An HSRP IPv6 group has a virtual MAC address that is derived from the HSRP group number and a virtual IPv6 link-local address that is, by default, derived from the HSRP virtual MAC address.
Periodic messages are sent to the HSRP virtual IPv6 link-local address when the HSRP group is active. These messages stop after a final one is sent when the group leaves the active state.
Note When configuring HSRP for IPv6, you must enable HSRP version 2 (HSRPv2) on the interface.

HSRP IPv6 Virtual MAC Address Range

HSRP IPv6 uses a different virtual MAC address block than does HSRP for IP: 0005.73A0.0000 through 0005.73A0.0FFF (4096 addresses)

HSRP IPv6 UDP Port Number

Port number 2029 has been assigned to HSRP IPv6.

How to Configure HSRP

Default HSRP Configuration

Table 1: Default HSRP Configuration

Feature	Default Setting
HSRP version	Version 1
HSRP groups	None configured
Standby group number	0
Standby MAC address	The system is assigned as: 0000.0c07.acXX, where XX is

HSRP Configuration Guidelines

HSRPv2 and HSRPv1 are mutually exclusive. HSRPv2 is not interoperable with HSRPv1 on an interface and the reverse.
In the procedures, the specified interface must be one of these Layer 3 interfaces:
Routed port: A physical port configured as a Layer 3 port by entering the no switchport command in interface configuration mode.
SVI: A VLAN interface created by using the interface VLAN vlan_id in global configuration mode, and by default a Layer 3 interface.
EtherChannel port channel in Layer 3 mode: A port-channel logical interface created by using the interface port-channel port-channel-number in global configuration mode, and binding the Ethernet interface into the channel group.
You can configure a maximum of 32 HSRP groups.
All Layer 3 interfaces must have IP addresses assigned to them.
HSRP millisecond timers are not supported.

Enabling HSRP

The standby ip interface configuration command activates HSRP on the configured interface. If an IP address is specified, that address is used as the designated address for the Hot Standby group.
If no IP address is specified, the address is learned through the standby function. You must configure at least one Layer 3 port

Enabling HSRP

on the LAN with the designated address. Configuring an IP address always overrides another designated address currently in use.
When the standby ip command is enabled on an interface and proxy ARP is enabled, if the interface’s Hot Standby state is active, proxy ARP requests are answered using the Hot Standby group MAC address.
If the interface is in a different state, proxy ARP responses are suppressed.

SUMMARY STEPS

configure terminal
interface interface-id
standby version {1 |2 }
standby [group-number]ip [ip-address [secondary]]
end
show standby [interface-id [group]]
copy running-config startup-config

DETAILED STEPS

	Command or Action	Purpose
Step 1	configure terminal

Example: Switch(config)# configure terminal

| Enters global configuration mode.
Step 2| interface interface-id

Example: Switch(config)# interface gigabitethernet1/0/1

| Enter interface configuration mode, and enter the Layer 3 interface on which you want to enable HSRP.
Step 3| standby version { 1 | 2 }

Example: Switch(config-if)# standby version 1

| (Optional) Configures the HSRP version on the interface.

• 1- Select HSRPv1.

• 2- Select HSRPv2.

**** If you do not enter this command or do not specify a keyword, the interface runs the default HSRP version, HSRP v1.

Step 4| standby [ group-number ] ip [ ip-address [ secondary ]]

Example: Switch(config-if)# standby 1 ip

| Creates (or enables) the HSRP group using its number and virtual IP address.

• (Optional) group number- The group number on the interface for which HSRP is being enabled. The range is 0 to 255; the default is 0. If there is only one HSRP group, you do not need to enter a group number.

• (Optional on all but one interface) ip-address- The virtual IP address of the hot standby router interface. You must enter the virtual IP address for at least one of the interfaces; it can be learned on the other interfaces.

	Command or Action	Purpose
		• (Optional) secondary – The IP address is a secondary

hot standby router interface. If neither router is designated as a secondary or standby router and no priorities are set, the primary IP addresses are compared and the higher IP address is the active router, with the next highest as the standby router.

Step 5| end Example: ** Switch(config-if)# end| Returns to privileged EXEC mode
Step 6| show standby [ interface-id [ group ]] Example: Switch # show standby| Verifies the configuration of the standby groups.
Step 7| copy running-config startup-config Example: Switch# copy running-config startup-config**| (Optional) Saves your entries in the configuration file.

Enabling and Verifying an HSRP Group for IPv6 Operation

In this task, when you enter the standby ipv6 command, a link-local address is generated from the link-local prefix, and a modified EUI-64 format interface identifier is generated in which the EUI-64 interface identifier is created from the relevant HSRP virtual MAC address.
A link-local address is an IPv6 unicast address that can be automatically configured on any interface using the link-local prefix FE80::/10 (1111 1110 10) and the interface identifier in the modified EUI-64 format. Link-local addresses are used in the stateless autoconfiguration process. Nodes on a local link can use link-local addresses to communicate; the nodes do not need site-local or globally unique addresses to communicate.
In IPv6, a device on the link advertises in RA messages any site-local and global prefixes, and its willingness to function as a default device for the link. RA messages are sent periodically and in response to router solicitation messages, which are sent by hosts at system startup.
A node on the link can automatically configure site-local and global IPv6 addresses by appending its interface identifier (64 bits) to the prefixes (64 bits) included in the RA messages. The resulting 128-bit IPv6 addresses configured by the node are then subjected to duplicate address detection to ensure their uniqueness on the link. If the prefixes advertised in the RA messages are globally unique, then the IPv6 addresses configured by the node are also guaranteed to be globally unique. Router solicitation messages, which have a value of 133 in the Type field of the ICMP packet header, are sent by hosts at system startup so that the host can immediately autoconfigure without needing to wait for the next scheduled RA message.

To enable and verify an HSRP group for IPv6, perform this procedure:

Enabling and Verifying an HSRP Group for IPv6 Operation

Procedure

	Command or Action	Purpose
Step 1	enable

Example:

Device> enable

| Enables privileged EXEC mode.

• Enter your password if prompted.

Step 2| configure terminal

Example:

Device# configure terminal

| Enters global configuration mode.
Step 3| ipv6 unicast-routing

Example:

Device(config)# ipv6 unicast-routing

| Enables the forwarding of IPv6 unicast datagrams.

• The ipv6 unicast-routing command must be enabled for HSRP for IPv6 to work.

Step 4| interface type number

Example:

Device(config)# interface GigabitEthernet 0/0/0

| Specifies an interface type and number, and places the device in interface configuration mode.
Step 5| standby [ group-number ] ipv6 { link-local-address |

autoconfig } Example: Device(config-if)# standby 1 ipv6 autoconfig

| Activates the HSRP in IPv6.
Step 6| standby [ group-number ] preempt [ delay minimum

seconds | reload seconds | sync seconds ]

Example: Device(config-if)# standby 1 preempt

| Configures HSRP preemption and preemption delay.
Step 7| standby [ group-number ] priority priority

Example: Device(config-if)# standby 1 priority 110

| Configures HSRP priority.
Step 8| exit Example: Device(config-if)# exit| Returns the device to privileged EXEC mode.
Step 9| show standby [ type number [ group ]] [ all | brief ]

Example:

** Device# show standby**

| Displays HSRP information.
| Command or Action| Purpose
---|---|---
Step 10| show ipv6 interface [ brief ] [ interface-type interface-number ] [ prefix ] Example: Device# show ipv6 interface GigabitEthernet 0/0/0| Displays the usability status of interfaces configured for IPv6.

Configuring HSRP Priority

The standby priority, standby preempt, and standby track interface configuration commands are all used to set characteristics for finding active and standby routers and behavior regarding when a new active router takes over.

When configuring HSRP priority, follow these guidelines:

Assigning a priority allows you to select the active and standby routers. If preemption is enabled, the router with the highest priority becomes the active router. If priorities are equal, the current active router does not change.
The highest number (1 to 255) represents the highest priority (most likely to become the active router).
When setting the priority, preempt, or both, you must specify at least one keyword (priority, preempt, or both)
The priority of the device can change dynamically if an interface is configured with the standby track command and another interface on the router goes down.
The standby track interface configuration command ties the router hot standby priority to the availability of its interfaces and is useful for tracking interfaces that are not configured for HSRP. When a tracked interface fails, the hot standby priority on the device on which tracking has been configured decreases by 10. If an interface is not tracked, its state changes do not affect the hot standby priority of the configured device. For each interface configured for hot standby, you can configure a separate list of interfaces to be tracked.
The standby track interface-priority interface configuration command specifies how much to decrement the hot standby priority when a tracked interface goes down. When the interface comes back up, the priority is incremented by the same amount.
When multiple tracked interfaces are down and interface-priority values have been configured, the configured priority decrements are cumulative. If tracked interfaces that were not configured with priority values fail, the default decrement is 10, and it is noncumulative.
When routing is first enabled for the interface, it does not have a complete routing table. If it is configured to preempt, it becomes the active router, even though it is unable to provide adequate routing services. To solve this problem, configure a delay time to allow the router to update its routing table.
Beginning in privileged EXEC mode, use one or more of these steps to configure HSRP priority characteristics on an interface:

SUMMARY STEPS

configure terminal
interface interface-id
standby [group-number] priority-priority
standby [group-number]preempt [delay [minimumseconds] [reloadseconds] [syncseconds]]
standby [group-number] track type number [interface-priority]
end
show running-config
copy running-config startup-config

DETAILED STEPS

	Command or Action	Purpose
Step 1	configure terminal

Example:

Switch # configure terminal

| Enters global configuration mode.
Step 2| interface interface-id

Example:

Switch(config)# interface gigabitethernet1/0/1

| Enter interface configuration mode, and enter the HSRP interface on which you want to set priority.
Step 3| standby [ group-number ] priority-priority

Example:

Switch(config-if)# standby 120 priority 50

| Sets a priority value used in choosing the active router. The range is 1 to 255; the default priority is 100. The highest number represents the highest priority.

• (Optional) group number—The group number to which the command applies.

** Use the no** form of the command to restore the default values.

Step 4| standby [ group-number ] preempt [ delay [ minimum seconds ] [ reload seconds ] [ sync seconds ]]

Example:

Switch(config-if)# standby 1 preempt delay 300

| Configures the router to preempt , which means that when the local router has a higher priority than the active router, it becomes the active router.

• (Optional) group-number-The group number to which the command applies.

• (Optional) delay minimum —Set to cause the local router to postpone taking over the active role for the number of seconds shown. The range is 0 to 3600 seconds (1 hour); the default is 0 (no delay before taking over).

• (Optional) delay reload —Set to cause the local router to postpone taking over the active role after a reload for the number of seconds shown. The range is 0 to 3600 seconds (1 hour); the default is 0 (no delay before taking over after a reload).

• (Optional) delay sync —Set to cause the local router to postpone taking over the active role so that IP

redundancy clients can reply (either with an ok or wait reply) for the number of seconds shown. The range is

	Command or Action	Purpose
		0 to 3600 seconds (1 hour); the default is 0 (no delay

before taking over).

** Use the no** form of the command to restore the default values.

Step 5| standby [ group-number ] track type number [ interface-priority ]

Example:

Switch(config-if)# standby track interface gigabitethernet1/1/1

| Configures an interface to track other interfaces so that if one of the other interfaces goes down, the device’s Hot Standby priority is lowered.

• (Optional) group-number- The group number to which the command applies.

• type- Enter the interface type (combined with interface number) that is tracked.

• number- Enter the interface number (combined with interface type) that is tracked.

• (Optional) interface-priority- Enter the amount by which the hot standby priority for the router is

decremented or incremented when the interface goes down or comes back up. The default value is 10.

Step 6| end

Example:

** Switch(config-if)# end**

| Returns to privileged EXEC mode.
Step 7| show running-config| Verifies the configuration of the standby groups.
Step 8| copy running-config startup-config| (Optional) Saves your entries in the configuration file.

Configuring MHSRP

To enable MHSRP and load-balancing, you configure two routers as active routers for their groups, with virtual routers as standby routers as shown in the MHSRP Load Sharing figure in the Multiple HSRP section. You need to enter the standby preempt interface configuration command on each HSRP interface so that if a router fails and comes back up, the preemption occurs and restores load balancing.
Router A is configured as the active router for Group 1, and Router B is configured as the active router for Group 2. The HSRP interface for Router A has an IP address of 10.0.0.1 with a group 1 standby priority of 110 (the default is 100). The HSRP interface for Router B has an IP address of 10.0.0.2 with a group 2 standby priority of 110.
Group 1 uses a virtual IP address of 10.0.0.3 and group 2 uses a virtual IP address of 10.0.0.4.

Configuring Router A SUMMARY STEPS

configure terminal
interface type number
no switch port
ip address ip-address mask
standby [group-number]ip [ip-address [secondary]]
standby [group-number] priority priority
standby [group-number]preempt [delay [minimum seconds] [reload seconds] [sync seconds]]
standby [group-number]ip [ip-address [secondary]]
standby [group-number]preempt [delay [minimum seconds] [reload seconds] [sync seconds]]
end
show running-config
copy running-config startup-config

DETAILED STEPS

	Command or Action	Purpose
Step 1	configure terminal

Example:

Switch # configure terminal

| Enters global configuration mode.
Step 2| interface type number

Example:

Switch (config)# interface gigabitethernet1/0/1

| Configures an interface type and enters interface configuration mode.
Step 3| no switch port

Example:

Switch (config)# no switch port

| Switches an interface that is in Layer 2 mode into Layer 3 mode for Layer 3 configuration.
Step 4| ip address ip-address mask

Example:

Switch (config-if)# ip address 10.0.0.1 255.255.255.0

| Specifies an IP address for an interface.
Step 5| standby [ group-number ] ip [ ip-address [ secondary ]]

Example:

Switch (config-if)# standby 1 ip 10.0.0.3

| Creates the HSRP group using its number and virtual IP address.

• (Optional) group number – The group number on the interface for which HSRP is being enabled. The range is 0 to 255; the default is 0. If there is only one HSRP group, you do not need to enter a group number.

• (Optional on all but one interface) ip-address – The virtual IP address of the hot standby router interface. You must enter the virtual IP address for at least one of the interfaces; it can be learned on the other interfaces.

• (Optional) secondary – The IP address is a secondary hot standby router interface. If neither router is designated as a secondary or standby router and no

	Command or Action	Purpose
		priorities are set, the primary IP addresses are

compared and the higher IP address is the active

router, with the next highest as the standby router.

Step 6| standby [ group-number ] priority priority

Example:

Switch(config-if)# standby 1 priority 110

| Sets a priority value used in choosing the active router. The range is 1 to 255; the default priority is 100. The highest number represents the highest priority.

• (Optional) group-number —The group number to which the command applies.

Use the no form of the command to restore the default values.

Step 7| standby [ group-number ] preempt [ delay [ minimum

seconds ] [ reload seconds ] [ sync seconds ]]

Example:

Switch(config-if)# standby 1 preempt delay 300

| Configures the router to preempt , which means that when the local router has a higher priority than the active router, it becomes the active router.

• (Optional) group-number-The group number to which the command applies.

• (Optional) delay minimum —Set to cause the local router to postpone taking over the active role for the number of seconds shown. The range is 0 to 3600 seconds (1 hour); the default is 0 (no delay before taking over).

• (Optional) delay reload —Set to cause the local router to postpone taking over the active role after a reload for the number of seconds shown. The range is 0 to 3600 seconds (1 hour); the default is 0 (no delay before taking over after a reload)

.

• (Optional) delay sync —Set to cause the local router to postpone taking over the active role so that IP

redundancy clients can reply (either with an ok or wait reply) for the number of seconds shown. The range is 0 to 3600 seconds (1 hour); the default is 0 (no delay before taking over).

Use the no form of the command to restore the default values.

Step 8| standby [ group-number ] ip [ ip-address [ secondary ]]

Example:

Switch (config-if)# standby 2 ip 10.0.0.4

| Creates the HSRP group using its number and virtual IP address.

• (Optional) group number – The group number on the interface for which HSRP is being enabled. The range is 0 to 255; the default is 0. If there is only one HSRP group, you do not need to enter a group number.

	Command or Action	Purpose
		• (Optional on all but one interface) ip-address – The

virtual IP address of the hot standby router interface. You must enter the virtual IP address for at least one of the interfaces; it can be learned on the other interfaces.

• (Optional) secondary – The IP address is a secondary hot standby router interface. If neither router is designated as a secondary or standby router and no priorities are set, the primary IP addresses are

compared and the higher IP address is the active

router, with the next highest as the standby router.

Step 9| standby [ group-number ] preempt [ delay [ minimum

seconds ] [ reload seconds ] [ sync seconds ]]

Example:

Switch(config-if)# standby 2 preempt delay 300

| Configures the router to preempt , which means that when the local router has a higher priority than the active router, it becomes the active router.

• (Optional) group-number-The group number to which the command applies.

• (Optional) delay minimum —Set to cause the local router to postpone taking over the active role for the number of seconds shown. The range is 0 to 3600 seconds (1 hour); the default is 0 (no delay before taking over).

• (Optional) delay reload —Set to cause the local router to postpone taking over the active role after a reload for the number of seconds shown. The range is 0 to 3600 seconds (1 hour); the default is 0 (no delay before taking over after a reload).

• (Optional) delay sync —Set to cause the local router to postpone taking over the active role so that IP

redundancy clients can reply (either with an ok or wait reply) for the number of seconds shown. The range is 0 to 3600 seconds (1 hour); the default is 0 (no delay before taking over).

Use the no form of the command to restore the default values.

Step 10| end

Example:

Switch(config-if)# end

| Returns to privileged EXEC mode.
Step 11| show running-config| Verifies the configuration of the standby groups.
Step 12| copy running-config startup-config| (Optional) Saves your entries in the configuration file.

Configuring Router B SUMMARY STEPS

configure terminal
interface type number
no switch port
IP address ip-address mask
standby [group-number]ip [ip-address [secondary]]
standby [group-number] priority priority
standby [group-number]preempt [delay [minimum seconds] [reload seconds] [sync seconds]]
standby [group-number]ip [ip-address [secondary]]
standby [group-number]preempt [delay [minimum seconds] [reload seconds] [sync seconds]]
end
show running-config
copy running-config startup-config

DETAILED STEPS

	Command or Action	Purpose
Step 1	configure terminal

Example:

Switch # configure terminal

| Enters global configuration mode.
Step 2| interface type number

Example:

Switch (config)# interface gigabitethernet1/0/1

| Configures an interface type and enters interface configuration mode.
Step 3| no switchport

Example:

Switch (config)# no switchport

| Switches an interface that is in Layer 2 mode into Layer 3 mode for Layer 3 configuration.
Step 4| ip address ip-address mask

Example:

Switch (config-if)# ip address 10.0.0.2 255.255.255.0

| Specifies an IP address for an interface.
Step 5| standby [ group-number ] ip [ ip-address [ secondary ]]

Example:

Switch (config-if)# standby 1 ip 10.0.0.3

| Creates the HSRP group using its number and virtual IP address.

• (Optional) group number – The group number on the interface for which HSRP is being enabled. The range is 0 to 255; the default is 0. If there is only one HSRP group, you do not need to enter a group number.

• (Optional on all but one interface) ip-address – The virtual IP address of the hot standby router interface. You must enter the virtual IP address for at least one of the interfaces; it can be learned on the other interfaces.

• (Optional) secondary – The IP address is a secondary hot standby router interface. If neither router is designated as a secondary or standby router and no

	Command or Action	Purpose
		priorities are set, the primary IP addresses are

compared and the higher IP address is the active

router, with the next highest as the standby router.

Step 6| standby [ group-number ] priority priority

Example:

Switch(config-if)# standby 2 priority 110

| Sets a priority value used in choosing the active router. The range is 1 to 255; the default priority is 100. The highest number represents the highest priority.

• (Optional) group number —The group number to which the command applies.