JOSOBO JS-CL001 LED RGB Night Light User Manual
- June 15, 2024
- JOSOBO
Table of Contents
JOSOBO JS-CL001 LED RGB Night Light
Product Diagram
- Touch Control
- Power Switch
- Timer Button
- LED Indicator
- Multicolor Light Mark
- Warm Light Mark
- Off Mark
- USB Charging Port
Specifications
| Power | 1.SW |
|---|---|
| Luminous Flux | 1001m |
| Battery Capacity | 2000mAh |
| Charging Time | 3.Sh |
| Working Time on a Full Charging | 7h (highest brightness) 100h (lowest |
brightness but not night light mode)
Working Voltage| DC 5V 1A
How to Use
Charging
Note:
- When the battery level is lower than 20%, the LED indicator will turn red.
- The LED indicator will keep blinking when charging and stay solid blue once fully charged.
- In standby mode, the LED indicator will blink on and off for easy locating in the dark.
Warm Light Mode
- Toggle the Power Switch to Warm Light Mark.
- Tap the Touch Control twice to turn on / off the light.
- Tap and hold the Touch Control to adjust the light brightness, release at the desired level. Tap and hold it again to adjust the brightness to the opposite direction.
Multicolor Light Mode
- Toggle the Power Switch to Multicolor Light Mork to enter automatic color carousel, where several color will cycle through.
- Tap the Touch Control once to stay in current color, tap it again to resume color carousel. The LED indicator will fiat twice to confirm your setting.
- Tap the Touch Control twice to turn on / off the light.
Memory Function
The Memory Function is enabled only in Standby mode.
Warm Light Mode/ Multicolor Light Mode
- To enter the Standby mode, top the Touch Control twice and the light will turn off indicating the light is under Standby mode.
- Tap the Touch Control twice again, the light will turn on and remain the last setting for Brightness (in Worm Light Mode) or Color Temperature (in Multicolor Light Mode)
Note: Do not toggle the Power Switch to OFF, or it will exit the Standby mode and reset the night light.
Night Light Mode
When the light is in Standby mode, top and hold the Touch Control for 1 second to enter night light mode.
Note: Night light mode is enabled only in Warm Light Mode.
Timer Setting
When the light is on, press the Timer Button once to set 1 hour timer with the LED indicator turning green.
Caution
- Do not attempt to alter or repair the unit. Return to the manufacturer for repairing.
- If a bod odor or on unusual operation is detected, turn off immediately.
- Do not place near any heat source, moisture, or corrosive substances.
- Regularly clean the lamp with a dry cloth.
- If not in use, regularly clean the unit. St ore in a dry and cool place.
- Use a 5V power adopters only, as other adopters may damage the product.
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
WEEE Compliance
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in countries with separate collection systems)
This marking on the product, accessories or literature indicates that the
product and its electronic accessories should not be disposed of with other
household waste at the end of their working life. To prevent possible harm to
the environment or human health from uncontrolled waste disposal, please
separate these items from other types of waste and recycle them responsibly to
promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this
product, or their local government office, for details of where and how they
can take these items for environmentally safe recycling. Business users should
contact their supplier and check the terms and conditions of the purchase
contract. This product and its electronic accessories should not be mixed with
other commercial wastes for disposal.
Customers Support
Contact customer support at