Electrolux ULTIMATEHOME 700 Lightweight Cordless Vacuum Cleaner User Manual

Electrolux ULTIMATEHOME 700 Lightweight Cordless Vacuum Cleaner

Product Information

Specifications:

• Model : EFW71711 / EFW71311
• Intended Use : Hard floor surfaces such as vinyl, tile, sealed wood, etc. NOT suitable for carpet/rug use
• Compatible Regions : Singapore, Malaysia, MENCA, Thailand, Indonesia, Australia, New Zealand, Korea
• Product Variants:
  • KSA-30C-260110HK (EFW71711)
  • KSA-30C-260110HT (EFW71711)
  • KSA-30C-260110HA (EFW71711)
  • KSA-30C-260085HA (EFW71311)
  • KSA-30C-260110HO (EFW71311)

Product Usage Instructions

Preparation

Before using the ULTIMATEHOME 700, make sure to follow these steps:

1. Ensure the product is fully charged by placing it on the charging stand and connecting the adaptor properly.
2. Install the brush roll provided or replace it if necessary.
3. Add clean water to the clean tank. Make sure the clean water tank is securely installed.
4. Make sure the dirty water tank is empty and properly installed (only applicable for EFW71711).

Operating Modes

The ULTIMATE HOME 700 offers different operating modes:

• TURBO AUTO: Automatically adjusts the power level based on the level of dirt and dust.
• TURBO MIN: Provides maximum power for intensive cleaning.
• TURBO MAX: Provides maximum power for heavy-duty cleaning.

Usage

Follow these steps to use the ULTIMATEHOME 700:

1. Turn on the product by pressing the ON button.
2. Select the desired operating mode using the appropriate button (TURBO AUTO, TURBO MIN, TURBO MAX).
3. Move the product over the hard floor surface, allowing the brush roll to agitate and clean the floor.
4. For stubborn stains or heavily soiled areas, you can manually adjust the power level using the provided controls.
5. Continue cleaning until the desired results are achieved.
6. Once finished, turn off the product by pressing the OFF button.

Self Cleaning Mode

The ULTIMATEHOME 700 features a self-cleaning mode for easy maintenance:

1. Press and hold the SELF-CLEANING button for 2 seconds to activate the self-cleaning mode.
2. The self-cleaning mode will run for approximately 2 minutes, ensuring the brush roll and internal components are thoroughly cleaned.

INSTRUCTIONS

CHARGING HUMIDITY SAFETY INSTRUCTIONS

POWER ON

HOW TO USE

TEMPERATURE

HOW TO CLEAN

EF162
Fine Dust Filter 4055838538
Brush Roll

TROUBLESHOOTING

water in the clean tank
The dirty tank is full| Empty the dirty tank
The brush roll is not installed| Install the brush roll or replace it
Low battery power| Fully charge the product
The brush roll is entangled with hair or other things| Clean the brush roll
Abnormal connection of electronic parts inside the handlebar| Return the product to the service network for repair
The suction is weakened| The dirty tank has reached its designated capacity| Take out the dirty tank, and empty the dirty water
The brush roll, Brush roll cover, dirty tank are not installed properly| Detached and install properly.
Nozzle or nozzle air tube is blocked| Clean up the nozzle and nozzle air tube
The filter is dirty or blocked| Clean or install the filter before using
No water come out from the nozzle| No water in clean tank| Add water in clean tank
The clean tank is not installed properly| Reinstall the clean tank
The clean tank check valve is blocked| Replace the clean tank
Pump blockage| Return the product to the service network for repair
Waterway blocked| Return the product to the service network for check and repair

The product cannot be charged

| The charging stand is not plugged in properly| Check that the plug is properly connected
The machine is not fully plugged into the charging stand| Check that the machine is positioned correctly
The adaptor is in poor contact with the charging stand| Check that the adaptor is properly connected to charging stand
The power level could not be automatically adjusted in AUTO mode| The bottom tube is dirty and blocked| Use the cleaning brush to clean up the bottom tube
Dirty water tank false alarm (The level of dirty water is much lower than max level)| Excessive cleaning solution is added, resulting in a large amount of foam| Follow the instructions for adding the amount of cleaning solution
The top cover of dirty water tank and solid-liquid separation holder are dirty| Use clean water to clean the top cover of dirty water tank and solid- liquid separation holder, and dry them with paper towels or towels, or let them dry for 24 hours before using
The “Dirty Water Tank Full” icon blinks| The dirty water tank is full| Dump the dirty water before using
The dirty water tank not installed properly (EFW71711)| Reinstall the dirty water tank
Self-cleaning is suspended or completed| The dirty water tank icon keeps flashing for 1 min, press the on/off button to stop blinking and enter the charging mode.
Icon blinks for clean water tank water shortage| Water shortage in clean water tank| Add water in clean water tank before using
Nozzle icon blinks          | Brush roll is entangled with an object such as hair or the brush roll is not installed| Clean or install the brush roll
Power display (3 LED lights) flash three times before turning off 3 times| The battery is out of power under undervoltage protection| Put it back in the charging base and charge it
Power display (3 LED lights) flash four times before turning off 4 times| Discharge overtemperature, the machine temperature is too high| Turn it off and let it sit for a while
Press the self-cleaning button when the unit is placed on the charging stand, but the self-cleaning does not start, while the self-cleaning icon and power display flash 5 times, then the 5 times unit returns to charging mode| Self- cleaning is not allowed to start when the battery is less than 33%| Keep charging until LED1 of power display is always on, then the self-cleaning function will be available
“TURBO” flashes on the display| Suction mode is activated by pressing “+/-“ button for one second. (Refer to the graphic on the center-right side of UI(display) introduction page)| Press the “+/-“ button again to exit the Suction mode.

FAQ’s

The floor washer is not working. What should I do?
Possible reasons and solutions include:

• Possible reason: Pump blockage.Solution: Add clean water in the clean tank.
• Possible reason: Waterway blocked.Solution: Empty the dirty tank.
• Possible reason: The brush roll is not installed or needs replacement.Solution: Install the brush roll or replace it.
• Possible reason: The product is not fully charged.Solution: Fully charge the product.

No water comes out from the nozzle. What should I do?
Possible reasons and solutions include:

• Possible reason: The bottom tube is dirty and blocked.Solution: Clean the bottom tube using the provided cleaning brush.
• Possible reason: The clean water tank is empty.Solution: Add water in the clean water tank before using.

The dirty water tank is full, but the dirty water level is  much lower than the max level. What should I do?

Possible reasons and solutions include:

• Possible reason: Excessive cleaning solution is added, resulting in a large amount of foam.
  Solution: Follow the instructions for adding the appropriate amount of cleaning solution.

• Possible reason: The top cover of the dirty water tank and  solid-liquid separation holder are dirty. Solution: Clean them using paper towels or towels, or let them dry  for 24 hours before using.

For more troubleshooting options and assistance, please refer to the complete user manual or contact our customer support.

References

• Electrolux

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>