amazon basics B078K4W8N9 Home Safe Instruction Manual

amazon basics B078K4W8N9 Home Safe

Contents

• Before getting started, ensure the package contains the following components:

NOTICE Do not store the key inside the safe. If the battery runs out you will not be able to open the safe.

Product Overview

Schematic drawing of the case

Schematic drawing of control panel

1. Reset Button
2. Locking Bolts
3. Battery Compartment
4. Knob
5. Yellow Light
6. Red Light
7. Green Light
8. Keypad
9. Key Cover

Opening the Safe for the First Time

1. To open the safe for the first time, remove the key cover by pressing the bottom of the cover marked with three lines.
2. Insert the key and turn it counterclockwise.
3. Turn the knob clockwise to open the door.
4. Turn the knob counterclockwise when closing the door.

Inserting batteries
On to bat ly and her batteries correctly with regard to polarity t+ and- marked

1. Open the safe door
2. Open the battery compartment and insert 4 x AA Alkaline batteries (not included),
3. Reachinem terrorist polarities.

NOTICE if the green and yellow lights turn on when you open the door with your password, this means the battery voltage is low and you should replace the batteries.

1. Open the safe door
2. Open the battery compartment and insert 4 x AA Alkaline batteries (not included), matching them to the correct polarities.
3. Replace the battery cover.

NOTICE If the green and yellow lights turn on when you open the door with your password, this means the battery voltage is low and you should replace the batteries.

Setting the Password

1. Remove the battery cover to locate the reset button. Press the reset button. The green light on the keypad will flash two times with two beeps.
2. Choose a new password (3-8 digits), enter it on the keypad and press the # key to confirm.
3. If the green light flashes two times together with two beeps, the new password is successfully set.
4. If the red light turns on together with five beeps, the safe fails to set the new password. Repeat the steps above until successful.

NOTICE Test the new password with the door open before locking the door.
Opening the Safe – Using Your Password

1. Input your password (3 to 8 digits) on the keypad. Press the # key to confirm.
   NOTICE
   If you enter the wrong code, press *, and the red light will turn on with 5 beeps, then all your inputted codes are deleted, you can try your password again.

2. If the password is correct, the green light will turn on. Rotate the knob clockwise within 5 seconds to open the door. After 5 seconds, the green light will turn off, and you will need to re-enter your password again to open the door.

3. If the red light turns on together with 5 beeps, it means the password is not correct.

NOTICE | The default preset password is “159”, change it immediately.

Locking the Safe
Close the door, then turn the knob counterclockwise to lock it.
Setting the Master Code

Should you forget your password, the safe can still be accessed with the master code.

1. Remove the battery cover to locate the reset button.
2. With the door open, press the 0 key twice and then press the Reset button. The green light on the keypad will flash two times with two beeps.
3. Input a master code of your choice (3-8 digits), then press the # key to confirm.
4. If the green light flashes two times together with two beeps, the master code is set.
5. If the red light turns on together with five beeps, the safe fails to set the new master code. Repeat the steps above until successful.

Turn the Keypad Sound Off/On

• To mute beeps, press and hold * for 5 seconds, the green light will flash once and then all lights will turn on for 1 second.
• Repeat the above step to unmute the beeps.

Automatic Lockout

1. The safe will enter a 5-minute lockout if the wrong password is entered 3 consecutive times.
2. After the 5-minute lockout, the green light will flash once together with 1 beep, indicating the lockout period is over.
3. During the lockout period, you can still use the key to open the door.

Securing the Safe to a Floor or Wall
Select a stable, dry and secure location for your safe.
If bolting to a wall, make sure that your safe is resting on a supporting surface (such as the floor or a shelf). Do not bolt your safe to both the floor and wall.

1. Place the safe on the selected location. Use a pencil to mark the mounting holes on the floor or wall.
2. Move the safe and drill 2-inch-deep mounting holes (~50 mm) using a 12 mm drill bit.
3. Put the expansion bolt (included) into the mounting hole, then turn the clamping screw counterclockwise to separate.
4. Move the safe back in place, align the safe over the holes. Then secure the safe with the clamping screw

Cleaning and Maintenance

• If necessary, wipe the outside and inside of the product with a slightly damp cloth.
• Avoid contact with corrosive substances like acids, alkaline or similar substances.

Troubleshooting

Environmental protection

• This marking indicates that this product should not be disposed of with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling.

• Used batteries must not be disposed of through household garbage, since they might contain toxic elements and heavy metals that can be harmful to the environment and human health.

• Consumers are therefore obligated to return batteries to retail or local collection facilities free of charge. Used batteries will be recycled.

• The crossed-out wheelie bin symbol indicates that batteries and rechargeable batteries must not be disposed of through household garbage.

• The symbols below the wheelie bin indicate:

• Pb: Battery contains lead

• Cd: Battery contains cadmium

• Hg: Battery contains mercury

• The packaging consists of cardboard and correspondingly marked plastics that can be recycled. Make these materials available for recycling.

Symbols Explanation

• This symbol stands for “Conformité Européenne”, which declares “Conformity with EU directives, regulations and applicable standards”. With the CE-marking, the manufacturer confirms that this product complies with applicable European directives and regulations.
• This symbol stands for “United Kingdom Conformity Assessed”. With the UKCA-marking, the manufacturer confirms that this product complies with applicable regulations and standards within Great Britain.

Specifications

• Model No: B078K4W8N9 (1.20 Cubic Feet/34Litre)
• Power supply (battery): 4 × 1.5 V , AA Alkaline battery
• Model No: B078K44SG4 (1.52 Cubic Feet/43 Litre)
• Power supply (battery): 4 × 1.5 V , AA Alkaline battery
• Model No: B078K2YPRW (1.80 Cubic Feet/51 Litre)
• Power supply (battery): 4 × 1.5 V , AA Alkaline battery

Importer Information

FCC – Supplier’s Declaration of Conformity

FCC STATEMENT

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Disposal (for Europe only)

The Waste Electrical and Electronic Equipment (WEEE) laws aim to minimise the impact of electrical and electronic goods on the environment and human health, by increasing reuse and recycling and by reducing the amount of WEEE going to landfill. The symbol on this product or its packaging signifies that this product must be disposed of separately from ordinary household wastes at its end of life. Be aware that this is your responsibility to dispose of electronic equipment at recycling centres in order to conserve natural resources. Each country should have its own collection centres for electrical and electronic equipment recycling. For information about your recycling drop- off area, please contact your related electrical and electronic equipment waste management authority, your local city office, or your household waste disposal service.

Feedback and Help

• We would love to hear your feedback. To ensure we are providing the best customer experience possible, please consider writing a customer review.
• Scan QR Code below with your phone camera or QR reader:

CONTACT

• UK: amazon.co.uk/review/review-your-purchases#
• If you need help with your Amazon Basics product, please use the website or number below.
• US: amazon.com/gp/help/customer/contact-us
• UK: amazon.co.uk/gp/help/customer/contact-us
• +1 877-485-0385 (US Phone Number)
• amazon.com/AmazonBasics.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>