JHK Gaming C-3595 Gaming Office Desk Chair Instruction Manual
- June 15, 2024
- JHK Gaming
Table of Contents
JHK Gaming C-3595 Gaming Office Desk Chair
Product Information
- Specifications
- Model: C-3595
- Assembly Guide: https://qygjuser.s3.us-east-2.amazonaws.com/HL/HLC-3595L-1.mp4.
- Package List
- (1)*1 Back
- (2)*1 Seat
- (3)*2 Armrest
- (4)*1 Mechanism
- (5)*1 Gas Lift
- (6)*5 Legs
- (7)*1 Base
- (8)*5 Casters
- (9)*4 Bolts
- (10)*8 Bolts
- (11)*10 Bolts
- (12)*8 Caps
- (13)*1 Wrench
- Assembly Instructions
- Step 1:
- Turn the Base (7) upside down, then insert Legs (6) one by one into the Base. Use the Wrench (13) to screw Ten Bolts (11) into the pre-drilled screw holes to fix the Base and Legs.
- Step 2:
- Insert the Casters (8) into the holes at the end of each Leg. Insert the Gas Lift (5) into the centre hole of the Base.
- Step 3:
- Align the Mechanism (4) over the pre-drilled holes underneath the Seat (2), making sure the front of the mechanism is facing the front of the Seat. Attach the Mechanism to the Seat using Four Bolts (9), and tighten all the bolts with the Wrench (13).
- Step 4:
- Turn the Seat (2) upright and align the centre hole of the Seat Plate over the lift, then push the Seat down onto the lift firmly until the connection is secure. Attach the Armrest (3) to the Seat (2) with Two Bolts (10), using the Wrench (13) to tighten. The
- Bolt only needs to be screwed in 50%. Repeat the same installation process for the other side Armrest.
- Step 5:
- Set the Back (1) stand up. Attach the Back (1) to the Arms by inserting one Bolt (10) in the holes with the Wrench (13). The Bolt only needs to be screwed in 50%.
- Step 6:
- Rotate the back of the chair up, then secure it with the Bolt (10) using the Wrench (13). Adjust the balance on each side of the chair, and tighten all the bolts at this step.
- Step 7:
- Press Caps (12) into screw holes on each side.
Product Usage Instructions
- Seat Height:
- Paddle-shaped lever on the right side
- To raise: While taking your weight off the chair, lift the lever.
- To lower: While seated, lift the lever.
- At the proper height, your feet should rest flat on the floor.
- Tilt Tension:
- Long stem under the seat with knob
- To increase tension: While seated, turn the knob forward (Counter-clockwise).
- To decrease tension: While seated, turn the knob backward (Clockwise).
- Set the tilt tension to control the resistance you feel when leaning back.
- Operating the tilt lockout:
- To let your chair tilt back, pull the control handle out. To stop your chair from tilting, sit forward, then push the control handle in.
- Armrests adjustment:
- The armrest can be adjusted up and down if needed.
- Safety and Maintenance
- Make sure all bolts and screws are fully tightened before using the chair. Lubricate all moving parts and tighten all bolts/screws every 6 months or whenever needed.
- FAQ
- Q: How often should I tighten the bolts and screws?
- A: It is recommended to tighten all bolts and screws every 6 months or whenever needed.
- Q: Can I adjust the armrests?
- A: Yes, the armrests can be adjusted up and down.
- Q: How do I increase or decrease the tilt tension?
- A: To increase the tilt tension, turn the knob forward (counterclockwise) while seated. To decrease the tilt tension, turn the knob backward (clockwise) while seated.
ASSEMBLY GUIDE
- Congratulations, you are now the owner of the new chair!
- Before enjoying the comfortable chair, you have to assemble it.
- This assembly guide will take you through the basic assembly process. To make sure your assembly progress goes smoothly, please follow the assembly instructions, especially the important safety information.
- It is possible to assemble the chair on your own, while having a second person to help you will make it easier.
- Please check if there are any missing parts in the package before starting. If there are any issues, please don’t hesitate to drop us an email and we’ll help you ASAP.
- If you run into any difficulty during the assembly, remember to check out the assembly Video to see if you’ve missed something. If you’re still unable to resolve your problems, drop us an email and our support team will assist you.
- https://qygjuser.s3.us-east-2.amazonaws.com/HL/HLC-3595L-1.mp4.
- WARNING: To ensure proper assembly, please follow all steps and use all parts. Failure to follow this warning can result in serious injury to yourself or others.
Package List
- Without further ado, we kindly suggest you list all the parts needed for the chair first.
Assembly Instruction
- Step 1:
- Turn the Base (7) upside down, then insert Legs (6) one by one to Base.
- Use the Wrench (13) to screw Ten Bolts (11) into the pre-drilled screw holes to fix Base and Legs.
- Step 2:
- Insert the Casters (8) into the holes at the end of each Leg.
- Insert the Gas Lift (5) to the center hole of the Base.
- Step 3 :
- Align the Mechanism (4) over the pre-drilled holes underneath the Seat (2), make sure the front of the mechanism is facing the front of the Seat.
- Attach the Mechanism to the Seat using Four Bolts (9), and tighten all the bolts with the Wrench (13).
- Step 4:
- Turn the Seat (2) upright and align the centre hole of the Seat Plate over the lift, then push the Seat down onto the lift firmly until the connection is secure.
- Attach the Armrest (3) to the Seat (2) with Two Bolts (10), using the Wrench (13)to tighten.
- The Bolt only needs to be screwed in 50%. The installation of the other side Armrest is the same.
- Note 1: The same marks on both the seat and armrests are tips for installing the armrests in the correct direction.
- Note 2: Armrests are labeled with the letter “L” (left) or “R” (right).
- Step 5:
- Set the Back (1) stand up.
- Attach the Back (1) to the Arms by inserting one Bolt (10) in the holes with the Wrench (13). The Bolt only needs to be screwed in 50%.
- Step 6:
- Rotate the back of the chair up, then secure it with the Bolt (10) use the Wrench (13).
- Adjust the balance on each side of the chair, and 100% tighten all the bolts at this step.
- Step 7:
- Press Caps (12) into screw holes of each side.
CAUTION: Make sure all bolts and screws are fully tightened before using a chair. Lubricate all moving parts and tight all bolts/screws every 6 months or whenever needed.
Instructions For Use
- Seat Height: Paddle-shaped lever on the right side
- To raise: While taking your weight off the chair, lift the lever.
- To lower: While seated, lift the lever.
- Tilt Tension: Long stem under the seat with knob
- To increase tension: While seated, turn knob forward (Counter clockwise).
- To decrease tension: While seated, turn knob backward (Clockwise ). Set the tilt tension to control the resistance you feel when leaning back.
- Operating the tilt lockout
- To let your chair tilt back, pull the control handle out.
- To stop your chair from tilting, sit forward, then push the control handle in.
- Armrests adjustment
- The armrest can be adjusted.
- Make it up and down if you need to.
Safety And Maintenance
- Do not stand on the chair, Do Not use the chair as a stepladder.
- Use this product for seating one person at a time.
- Do not use the chair unless all bolts and screws are firmly secured.
- Avoid contact with sharp objects to prevent puncturing the fabric.
- Every 6 months, check all bolts and screws to ensure they are tight.
- To clean, spot clean only using a damp towel and mild cleaner, first test on a small, unseen area of fabric.
- Chair weight limit not to exceed 250 lbs.
Safety Information
SEATING USAGE:
- Normal use for seating is identified as the equivalent of a single shift, forty- (40) hour workweek.
- To the extent that a seating product is used in a manner exceeding this, the applicable warranty period will be reduced in a pro-rata manner.
- Some retailers might have custom models imported directly from the factory and therefore are not supported by our local service team because we don’t have the correct parts, please contact your retailer directly for support.
- If you have any questions about that we will be happy to assist and identify those items.
RETURN POLICY：
- We adopt a 30 days return policy which means that all products purchased on this website may be returned to us within the timeframe.
- You need to contact us within 30 days after the product(s) came into your possession and the product(s) must be returned to us without any undue delays.
- Returned products must be returned in the same condition as they were sent and they must be sent in its original packaging.
- If the product is not faulty, (i.e. if you changed your mind or if you are unhappy with the product for some other reason), the cost of shipping will all on you.
- And it is your responsibility that the package arrives safely to us so we recommend that you use a courier service where it is possible to track the shipment.
- If the product is faulty when you receive it please contact us and we will help you out (see more information under Manufacturer Warranty).
- We reserve the right to give a partial refund in cases when the product(s) is not in an unused condition, is damaged or has missing parts not due to our error.
HOW RETURNS WORK
- Contact us through the contact form on our website and attach the invoice to the message as proof of purchase.
- And please also write the reason for return.
- We will then get back to you as soon as possible with information on where to send the product(s).
- As soon as we have received the product(s) and made an inspection we will inform you of our decision.
- If a refund is approved we will automatically credit the purchase to your credit card or original method of payment.
- If the product(s) is damaged, not in its original condition or missing parts we will inform you if you are eligible for a partial refund.
- This is decided from case to case depending on the severity of the damages or what parts are missing.
- Model: C-3595
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>