Ohuhu Front Door Handle Set User Manual

Ohuhu Front Door Handle Set

Please read this user manual before fitting and using your door lock! If you need help, please let us know.

Front Door Handle Set Installation Instruction

Contents

Before getting started, please ensure the package contains the components below:

Packing List

Precautions for Installation

• Remove the packaging film on the product.
• Please check and see if there is any damage on the product.
• Please check and see if any installation components is missing.
• Make sure the thickness of the door is between 1-3/B”and 1-3/4″ (35mm-45mm).

Left- or Right- Handed Door Installation

Stand outside and face the door:

• if the hinges are installed on the left, the door is left-handed.
• if the hinges are installed on the right, the door is right-handed.

Tools to Prepare

2-1/8″ (54mm)

Drill Hole Saw

| Electronic Drills| 1″ (25mm)

Drill Bit

| 3/8″(1Omm) Drill Bit|

Stand Outside and Face the Door

• Fold the supplied template along the fold line and place on the exterior side of your door.
• Mark the location of the new holes on your door according to the template, and then drill the holes.

INSTALLATION

• Step 1: Drill Holes into the Door

  • CD Measure and check that the diameter of the hole in the door is 2-1/8″(54mm)
  • Measure and check that the backset if either 2-3/8″ or 2-3/4″ (60mm or 70mm)
  • Measure and check that the diameter of the side hole in the door is 1 “(25mm)
  • Mark for 1-3/8″ (35mm)or 1-3/4″ (45mm) Door
    Insert the latch and ensure it is parallel to the face of the door. Mark the out line of the face plate, and then take out the latch.
    Chisel 5/32″ (4 mm) deep along the outline to allow the face plate to be aligned with the door edge.

• Step 2: Adjust the Length of the Latch

  • Determine if the latch needs to be adjusted to the 2-3/4R (70mm) backset.
  • To adjust, rotate the latch until it stops.
  • Reverse the direction to return to the 2-3/8″ (60mm) backset.

• Step 3: Install the Deadbolt Latch Set

  • Use two 3/4″ (20mm) screws to tighten the latch into the door. Do not over-tighten.
  • Use two 3/4″ (20mm) screws to tighten the latch into the door. Do not over-tighten.

• Step 4: Install the Exterior Deadbolt

• Step 5: Install the Interior Deadbolt

• Step 6: Install the Exterior Handle
  Adjustable Bolt Design

• Step 7: Install the Interior Handle

• Step 8: Install the Cover

• Step 9: Install Strikes

Troubleshooting

• Is this product suitable for left- or right-handed door?

  • How can I determine if the door is left- or right-handed?

• Yes, it is suitable for both left-and right-handed door.
  To determine the handing of your door ,please stand outside the door and face the door:

  • If the hinges are installed on the left, the door is left-handed.
  • If the hinges are installed on the right, the door is right-handed.

• The screw is too long or too short to be installed.

  • Please match the screws in different sizes according to different positions in strict  accordance with the instructions.

• After the Installation, I can only open the door with the button or the handle, but the deadbolt can’t work.

  • Please make sure the lacth of the deadbolt is installed in the middle of the rotation axis.

• Determine if the latch needs to be adjusted to the 2-3/4″ (70mm) backset.

  • Please make sure the key hole is back to its original position before installing the lock.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>