RISTOW ‎RVDOORLOCK-002 Keyless Entry Door Lock User Manual

RISTOW ‎RVDOORLOCK-002 Keyless Entry Door Lock

Structure Size

Locks installed

1. Unscrew and remove platen assembly
2. Install the front half assembly into the door panel hole
3. Plug into socket, Then knob is inserted Into the rotating shaft with azimuth alignment
4. Assemble the platen assembly with the front part assembly
5. Mounting deadplate
6. Mounting pinchplate

How to lock or unlock

1. Password: enter the factory password 1234, and then press the unlock key to unlock the door. Enter the factory password 1234, then press the lock key, the door lock will be closed

2. Bluetooth key: after you set FOB remote (on page 5), you can use the bluetooth key to lock it or unlock it directly

3. Mechanical key: the rv lock has 2 lock cylinders, one locks the rv lock panel and the other locks the door. You need to unlock the 2 lock cylinders to unlock it, Similarly, you need to lock the 2 lock cylinders, the door locked ( note: the back button should turn to ” on “)

4. Long press the lock button to lock

How to reset the password

• Step 1
  Long press the number 8 button with your right hand, then press the lock button with your left hand, press and hold both buttons for 1-2 seconds at the same time, 2 beep will be heard, then release the lock button first, and then release the number 8 button immediately, and the numeric keypad will start flashing, which means the operation is successful.

• Step 2
  Enter the fatory password 1234 + lock button to confirm
  Initial password: 1234

• Step 3
  Enter the new password + Lock button within 2 seconds (the new password needs to be entered twice), you will hear 2 beep sound, the new password is successfully set, and the number of passwords is not limited.

How to set FOB remote

1. Hold the screwdriver in one hand and press the fob learn hole for 2-3 seconds, Hold down any button on the remote control with the other hand and aim at the combination lock,
2. Then you will hear a sound of bi, the connection is successful.
3. If two remote controls are used interchangeably, and there is a stuck problem, it is the code lock processing signal, which is a normal phenomenon. You can press the remote control button repeatedly to operate normally. Using the reset function

Using the reset function

If you repeatedly set the password or bluetooth key, it may disrupt the program of the combination lock and cause the password or key to fail. Please don’t worry, you can reset the combination lock (use a screwdriver to long press hold code reset (on the back) and you will hear a sound of bi), the combination lock will become the original appearance, and the password will also change. into 1234, after reset, you can reset the password or bluetooth key again.

To replace a battery

To replace a battery, perform the following operations:

1. Remove the back battery door screw with a screwdriver.
2. Open the battery door and place the battery, note: the battery on the left side and the battery on the right side need to be flipped in the opposite way, pay attention to the position of the battery spring for installation.
3. Snap on the battery door and screw, you can complete the battery installation.

Common problems

• Why does the remote control not work?
  Please check

1. Whether the ON/OFF button on the back of the password lock is switched to ON, if it is in the OFF state, the remote control function is not working.
2. Check whether the red light is on when the remote control presses the switch, if not, it means the battery is not charged.
3. Be sure to confirm that the pairing of the remote control has been completed before using the remote control.
4. Ensure that the combination lock is operated within the available range of the remote control, and the maximum remote control range is 15m (50ft)

• How to eliminate the sound of the keys?
  Press and hold the “1” button to turn off the key sound, and press and hold the number “1” again to restore the key sound.

• Forget the reset password, how to restore to the factory password 1 2 3 4?
  Use the screwdriver in the package and press and hold the “Code Reset” button on the back of the combination lock to restore the factory settings.

• Is the product suitable for Class A and Class C RVs?
  No. It does not fit Class A and C motorhomes, it fits lock hole opening: 3.75 “W x 2.75 “T x 1.5 “D. Please check the opening size and latch style before purchase.

• Can I use the two remotes together?
  Yes, they can be used together, they need to be paired separately, and they can be used together after the pairing is completed.

• What do I need to pay attention to when resetting the password?

1. The first step must confirm that you hear the beeping sound and the screen starts flashing before proceeding to the next step, otherwise you have to continue to complete the first step until the keyboard flashes.
2. Confirm that the old password is entered once and the new password is entered twice, and the beeping sound will be heard after completion to represent successful password setting. After the password reset, the initial password “1 2 3 4” will be invalid.
3. The maximum number of digits of the new password is 8. For example, the password of 1234567876 can be opened with 12345678, and the system only records the first 8 digits of the password.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>