KOSS CKARA2432CCT-TS Kara LED Medicine Cabinet Installation Guide

KOSS CKARA2432CCT-TS Kara LED Medicine Cabinet

Product Information

The Suite Mirror Cabinet KARA is a high-quality cabinet designed for installation in Zones 2 and 3. It is not suitable for installation in Zone 1. The cabinet comes with a handle and should be handled with care to avoid any damage. It is important to avoid placing the cabinet upright on hard surfaces such as tile floors. Always lay it on a soft surface to prevent any scratches or dents.

Important Note
It is highly recommended to use a wire gauge less than 12mm in diameter to avoid potential damage to the back of the cabinet.

Product Usage Instructions

The Suite Mirror Cabinet KARA features touch buttons for easy operation. Follow these instructions to use the touch buttons:

1. ON/OFF: Tap the touch button once to turn the light on and off.
2. Color Temperature Change: When the light is on, short-press the touch button within 4 seconds to change the color temperature. Press the button again to cycle between 3000K, 4000K, and 6000K.
3. Dimming: When the light is on, press and hold the sensor button to dim the light. Release the button to set the desired brightness level.

The cabinet also features a memory function that preserves the previous color temperature and brightness settings, making it convenient for daily use.

Specifications

• Product Name: Suite Mirror Cabinet KARA
• Part Number: CKARA2432CCT-TS
• Installation Zones: 2 and 3
• Recommended Wire Gauge: Less than 12mm in diameter

Part Number : CKARA2432CCT-TS

This cabinet is suitable for installation in Zones 2 and 3 only. Avoid Installation in Zone 1. See diagram above.
Please read through these instructions carefully and refer back to them during installers ensure that your product is fitted safely and that it retains its high quality finish
Please retain this document for future reference.

WARNING: Handle with care! When unpacked, do not place cabinet upright directly on a hard surface, such as tile floors. Always lay on a soft surface

INSTALLATION

• Using a spirit level, mark a horizontal line and plug holes in the proper position of the wall.
• Drill the required holes to a suitable depth.
• Screw the bracket to the wall by using the screws provided.
• Hand the cabinet on the wall bracket. The claws on the cabinet hangers must be securely located on the wall bracket. Connect the wire to the local power wire.

Wiring Diagram

WEEE compliance
Must not be mixed with general household waste

Screw the support bracket at the bottom of the cabinet and wall to stable it.

1. Mark the mounting point of the support bracket on the wall with a soft pencil.
2. Drill the mounting point to a suitable depth.
3. Fix the support bracket.

CAUTION: To avoid potential damage to the back of the cabinet, it is highly recommended to use a wire gauge less than 12mm in diameter.

Correct Wiring

Incorrect Wiring

HOW TO USE THE TOUCH BUTTON

• ON/OFF: Tap the touch button to turn on the light ON and OFF.
• Color Temperature Change: When the light is on, short press the touch button within 4 seconds to change the color temperature from 3000K to 4000K to 6000K.
• Dimming: When the light is on, press and hold the sensor button to dim the light.
  • The cabinet is equipped with a memory feature to preserve the previous color temperature and brightness settings.

FAQ

• Can the Suite Mirror Cabinet KARA be installed in Zone 1?
  No, the cabinet is not suitable for installation in Zone 1.

• What should I do if I accidentally place the cabinet upright on a hard surface?
  If you accidentally place the cabinet upright on a hard surface, ensure to check for any damages. It is always recommended to lay the cabinet on a soft surface to prevent scratches or dents.

• How do I change the color temperature of the light?
  To change the color temperature, tap the touch button within 4 seconds of turning on the light. Each tap will cycle through different color temperatures (3000K, 4000K, and 6000K).

• Can I dim the light of the cabinet?
  Yes, you can dim the light by pressing and holding the sensor button. Release the button to set the desired brightness level.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>