Loolinn Z6Pro GPS Drone with Camera User Manual

Loolinn Z6Pro GPS Drone with Camera

Product Information

Specifications

• Operating frequency Range: Not specified
• Operating conditions : Not specified
• Charging time: Not specified

About this Product

The Z6Pro GPS Brushless Drone is a high-quality drone designed for aerial photography and recreational flying. It features a 500m image transmission range and comes with a 5G WIFI camera for real-time video streaming. The drone is equipped with GPS tracking, allowing for precise positioning and navigation. It also offers various flight modes such as one key to return, circle flight, flight plan, waypoint flight, human tracking, and palm control. The drone utilizes optical flow positioning for enhanced stability during flight. With long battery life and dual-frequency technology, the Z6Pro is a reliable and efficient drone for both beginners and experienced users.

Safety Guide

1. Adult or experienced RC pilot’s supervision is recommended for children.
2. Rechargeable batteries are only to be charged under adult supervision.
3. Turn off the drone/transmitter and remove the batteries whennot in use.
4. The supply terminals are not to be short-circuited.
5. Keep away from the rotating blades (rotating blades may cause bodily injuries or damage to property).
6. Assemble the drone with the guidance of adults.
7. Do not look directly into the LED lights of the drone as they may make your eyes uncomfortable.
8. Exhausted batteries are to be removed from the drone.
9. Store the smaller-sized drone accessories in places that are out of reach of children.
10. For all first-time flights, the left joystick must be used with caution as the drone is very powerful.

Repair and Maintenance

1. Use a clean and soft cloth to clean the product.
2. Keep the product away from heat sources.
3. Avoid water exposure to this product as moisture may cause damages to the drone electronic parts.
4. Regularly examine transformers used with the drone, such as the cord, plug, enclosure, and other parts. If any damages are found, please stop using it unless it is repaired or replaced.

Drone Components

• Motor
• Propeller blades
• Power switch
• Front camera

Remote Control

• Battery
• Front LED indicator
• Rear LED indicator
• Bottom camera
• Right joystick

Assembling the Product

1. Install the propellers in the correct orientation as shown in the diagrams above.
2. Ensure that the clockwise and anticlockwise propellers are attached to the correct arms. The drone will not fly correctly if the propellers are attached in the wrong position.
3. Take note that the propellers are made from a delicate material. Pay attention when attaching them to the drone.
4. Only use propellers that are supplied by the manufacturer.
5. The propellers are consumable parts. If necessary, purchase replacements from the manufacturer.

Product Usage Instructions

To use the Z6Pro GPS Brushless Drone, follow these steps:

• Step 1: Download and install the Loolinn Air App
  For Android phones, download and install the Loolinn Air App by visiting Google Play or by scanning the QR code. For iOS Apple phones, download and install the Loolinn Air App by visiting the App Store or by scanning the QR code. Please ensure that your device has iOS 8.0/Android 5.0 or later for optimal performance.

• Step 2: Power on the Drone and Remote Control
  Ensure that both the drone and remote control are powered on. The power switch is located on the drone and the batteries are inserted into the remote control. Make sure to follow the safety guidelines mentioned earlier.

• Step 3: Connect the Drone and Mobile Phone
  Connect your mobile phone to the drone’s 5G WIFI camera. Please ensure that your mobile phone supports 5G WiFi for proper image transmission.

• Step 4: Calibrate the Drone
  Before flying, it is recommended to calibrate the drone for accurate flight performance. Follow the instructions provided in the user manual to calibrate the drone’s compass and gyroscope.

• Step 5: Select Flight Mode
  Choose the desired flight mode based on your preferences and needs. The Z6Pro offers various flight modes such as one key to return, circle flight, flight plan, waypoint flight, human tracking, and palm control. Refer to the user manual for detailed instructions on each flight mode.

• Step 6: Take Off and Fly
  Once the drone is calibrated and flight mode is selected, you can take off by gently pushing the throttle joystick upwards. Use the remote control’s joysticks to control the drone’s movement.Practice flying in open areas away from obstacles and follow local regulations for drone flying.

• Step 7: Landing and Power Off
  To land the drone, slowly reduce the throttle until the drone descends gently. Once landed, power off the drone and remote control. Remember to remove the batteries from the drone and store them safely.

FAQ

What is the operating frequency range of the Z6Pro GPS Brushless Drone?
The operating frequency range is not specified in the user manual. Please refer to the manufacturer’s specifications for more information.

Can I fly the drone in rainy conditions?
No, it is recommended to avoid water exposure to the drone asmoisture may cause damages to the electronic parts. Fly the drone in dry weather conditions for optimal performance.

Where can I purchase replacement propellers?
If necessary, you can purchase replacement propellers from the manufacturer. Please contact their customer support or visit their official website for more information.

Important safety information
Thank you for purchasing this Loolinn product. To ensure that you operate the drone correctly, please read these instructions carefully before first use and store them in a safe place for future reference.

Safety Guide

1. Adult or experienced RC pilot’s supervision is recommend for children.
2. Rechargeable batteries are only to be charged under adult supervision.
3. Turn off the drone/transmitter and remove the batteries when not in use.
4. The supply terminals are not be short-circuited.
5. Keep away from the rotating blades (rotating blades may cause bodily injuries, or damage to property).
6. Attention：please assemble the drone with the guidance of adults.
7. Do not look directly into the LED lights of the drone as make your eyes uncomfortable.
8. Exhausted batteries are to be removed from the drone.
9. Please store the smaller-sized drone accessories in places that are out of reach of children.
10. This drone is very powerful. For all first-time flights, the left joystick must be slowly pushed up in order to prevent the drone from ascending too fast to avoid unnecessary collision and possible damage and injury.
11. When the flight is ended, first turn off the power of the remote control. Then turn off the power of the drone.
12. Avoid placing the batteries in places with high temperatures and exposure to heat.
13. Please keep a safe distance from the spinning propellers to avoid injury.
14. To ensure the electromagnetic environment requirement of the aviation radio (station), using remote controls in the zone, which is in a radius of about 5000m zone from the circle center of the airport runway, is forbidden. All users also should abide by the regulation of the radio set forth by government and regulatory agencies including the duration and area.
15. Pay attention to keeping distance of 2-3 meters from the user or other people when the drone is flying, avoid the drone landin to hit the head, face or face or body of anoter person.
16. The packing has to be kept since it contains important information.

Repair and maintenance

1. Use clean and soft cloth to clean the product.
2. Keep away the product from heat sources.
3. Avoid water exposure to this product. Moisture may cause damages of the drone electronic parts.
4. Transformers used with the drone should be examined regularly,such as the cord,plug,enclosure and other parts,If any damages are found, please stop using it unless it is repaired or replaced.

About this product

Specifications

Drone

• Drone weight: 216 g
• Drone Size: 305x280x65 mm
• Range: 500 m
• Altitude: 100 m
• Image transmission range: 500 m
• Flight time: Hovers indoors for 24-25 minutes
• Operating conditions: 0°C to 40°C
• Video transmission frequency: 5 GHz
• Motor: 1503 Brushless motor
• Battery: 7.6 V 1700 mAh
• Charging time: About 3 hours

Remote control

• Operating frequency: 2.4 GHz
• Range: 500 m
• Operating conditions: 0°C to 40°C
• Charging time: About 1 hours

Package contents

• Drone: 1
• Remote control: 1
• USB charging cable: 2
• Clockwise/anticlockwise propellers: 4
• Instructions: 1

Download and install the Loolinn Air App

• For Android phones, download and install the Loolinn Air App by visiting Google Play or by scanning the QR code.
• For IOS Apple phones, download and install the Loolinn Air App by visiting the App Store or by scanning the QR code.

Note : For best results, use a device with iOS 8.0/Android 5.0 or later.

Drone components

1. Motor
2. Propeller blades
3. Power switch
4. Front camera
5. Battery
6. Front LED indicator
7. Rear LED indicator
8. Bottom camera

Remote control

Assembling the product

Installing the propellers

1. Clockwise propellers
2. Anticlockwise propellers

• Attach the propellers as shown in the diagrams above. Ensure that they are attached in the correct orientation.
• Ensure that the clockwise and anticlockwise propellers are attached to the correct arms. The drone will not fly correctly if the propellers are attached in the wrong position.
• The propellers are made from a delicate material. Pay attention when attaching them to the drone.
• Only use propellers that are supplied by the manufacturer.
• The propellers are consumable parts. If necessary, purchase replacements from the manufacturer.

Inserting a memory card
(optional accessory)

Charging the drone battery

• Remove the battery
• Charge the battery

Charge the drone with the USB charging cable that came with the product.
The battery will take longer to charge when you use an adapter with a smaller rated current.

Insert the battery

Ensure that the battery holder clicks into place.

• Do not short circuit or compress the battery, as this may cause an explosion.
• Do not disassembling the battery or store it in a hot environment.
• If you do not plan to use the drone for at least 10 days, discharge thecbattery to 40%-50%. This helps to prolong the lifespan of the battery.
• Rechargeable batteries should be removed from the drone before being charged.
• Rechargeable batteries should only be charged under the supervision of adults.and keep away from flammable materials.
• Exhausted batteries should be removed from the drone.
• Caution: Risk of explosion if battery is replaced with incorrect ones, please install the batteries according to the instructions.

Attaching the phone holder

Charging the remote control batteries

Flight preparation and turning the drone on/off
Pairing the remote control with the drone

• Switch on the remote control Indicator flashes rapidly -> slowly
  • Remote control indicator flashes rapidly
  • Indicator stays constant when pairing is complete.

When you switch on the remote control, the indicator will flash rapidly for approximately 20 secs to indicate that the remote control is waiting for a signal. The indicator will then flash slowly to indicate that pairing mode has been disabled.

Calibrating the compass

• Press to calibrating the compass
• Hold the drone horizontally and rotate 360 degrees for few time. Indicator flashes from slowly to rapidly.
• Hold the drone vertically and rotate 360 degrees for few times. Indicator flashes from rapidly to constant.

Do not calibrate the compass near strong electromagnetic fields or large pieces of metal, e.g. magnetite, car parks or buildings with underground steel reinforcements.
When holding the drone horizontally, the angle of inclination must not exceed 30 degrees.

Searching for satellites
The rear indicator will change from orange to green when the drone has locked on to a satellite and recorded the take-off location. The drone is now ready to fly.

• It should take approximately one minute for the drone to lock on to a satellite. If the drone fails to find a satellite, recalibrate the compass.
• Before take-off, place the drone in an open space away from obstacles and ensure that GPS mode is enabled.
• When the rear green indicator flashes rapidly, this indicates that the GPS signal is weak. If this occurs, land the drone manually and restart the satellite search.

Turning the drone on

1. Move the left joystickcupwards
2. Push the left and right joysticks downwards in a V shape for 1 second.

Turning the drone off

• Push the left joystick downwards for 2-3 seconds.
• Push the left and right joysticks downwards in a V shape for 2 seconds.
• Press the take-off/landing button to make the drone land automatically and switch off.

The drone will switch off automatically if its angle of inclination exceeds 90 degrees.

Using the remote control

Flight modes

Optical flow positioning
Front indicator is constant white, rear indicator is constant yellow.

• If the rear indicator starts to flash rapidly, this indicates that the optical signal is weak and the drone cannot determine its position.
• Performance may be impaired in dark surroundings, areas with reflective surfaces (e.g. water), or at altitudes of more than 6 m.
• Optical flow positioning only supports altitudes of less than 6 m.

GPS mode
Front indicator is constant white, rear indicator is constant green.

• When the battery level is normal, the drone can fly to a distance of 500 m at a maximum altitude of 100 m.
• When the battery level is low, the drone can fly to a distance of 20 m at a maximum altitude of 20 m.
• If the rear indicator starts to flash rapidly, this indicates that the GPS signal is weak and the drone cannot determine its position.
• GPS mode cannot be used indoors.

Headless mode
The indicator on the drone will flash once every 4 seconds.

1. Configuring the forwards direction
   When you switch on the drone for the first time, the direction in which the front side of the drone is pointing will be set as the forwards direction.

2. Enabling headless mode

3. After pairing the remote control with the drone, hold down the right joystick for approximately 3 seconds. The remote control will beep 8 times to indicate that headless mode is enabled. To disable headless mode, hold down the right joystick again for approximately 3 seconds.

4. In headless mode, you do not need to determine the drone’s orientation. You can move the joysticks on the remote control to make the drone move in the corresponding direction.

Level calibration
Place the drone on a level surface and move the left and right joysticks to the lower right corner for approximately 3 seconds. The indicator will flash rapidly and then stay constant to indicate that the calibration process is complete.

The drone cannot be calibrated if the angle of inclination is greater than 10 degrees.

High/low speed mode
Briefly press the right joystick to switch between high and low speed mode.

1. Low speed mode is enabled by default when the drone is switched on.
2. The remote control beeps twice when high speed mode is enabled and once when low speed mode is enabled.

One – Key take-off/landing

1. When the drone is under standby mode,Press the take-off/landing button to make the drone take off automatically and hover at a height of 1.5 m.
2. When the Drone is under active mode, it will automatically land on ground if you press the one key landing

Taking a photo or video recording with the remote control

1. Take a photo:
   Press the photo button. The indicator on the drone will flash to indicate that a photo is taken.

2. Record video:
   Press the record button. The indicator on the drone will flash twice to indicate that recording is in progress. Press the record button again to end the recording. The indicator on the drone will turn on to indicate that recording is complete.

Taking a photo or video recording with hand gestures

1. Take a photo:
   Position your hand approximately 1.5 m away from the front lens and hold the hand gesture for 3 seconds.

2. Record video:
   Position your hand approximately 1.5m away from the front lens and hold the hand gesture for 3 seconds.

CAUTION

Photo and video recording gestures cannot be used when the bottom camera is on. （See Loolinn Air App User Manual for further information）

• The camera may accidentally take a photo or start a video recording if there are surrounding objects that resemble the or gestures.
• If there is no memory card in the drone, photos and video recordings will be saved to your phone.
• If there is a memory card inserted in the drone, photos and video recordings will be saved to the memory card and your phone.
• The drone supports memory cards with a capacity of up to 64 GB.

Return to home function

In GPS mode (when the indicator is constant), hold the return to home, so the drone will return to its take-off position automatically. During the return flight, you can use the joystick to control the drone ascend, descend and move left/right in order to avoid obstacles. To terminate the return flight, hold the return to home button.

• If the drone is flying at an altitude less than 20 m, it will automatically ascend to an altitude of 20 m before returning home.
• If the drone is flying at an altitude more than 20 m, it will return home at the same altitude.

No signal
If the remote control signal is lost for more than 6 seconds, the drone will automatically return to the take-off position. If the signal is restored during the return flight, you can hold the return to home button to terminate the return flight. The drone cannot automatically avoid obstacles during the return flight.

• The automatic return to home function is not available when the GPS signal is weak (flashing indicator).
• If the drone does not receive a GPS signal and lost contact with the remote control for more than 6 seconds, it will not be able to return to home but will land automatically.

Automatic return due to low battery
When the drone battery is low, the drone will automatically return to the take-off position. During the return flight, you can use the joystick to control the drone ascend, descend and move left/right in order to avoid obstacles.

• If the drone is further than 20 m from the landing position, the return flight cannot be terminated.
• If the drone is less than 20 m from the landing position, the return flight can be terminated.

Landing position:
The initial unlock/take-off position

Smart Loolinn Air app features

Function description of operation interface

• WiFi
  Show the strength of the image transmission signal;

• Satellite signal
  Show the current flight mode and the number of satellites. Steady light indicates it is the GPS mode, so the GPS Auto return to home, GPS tracking, round flight, waypoint flight are available. Flashing indicates that it is the optical flow fixed-point mode, so master tracking, palm control, trajectory flight are available.

• Battery State
  Battery State of drone
  2-4 bars indicate normal power. In GPS mode, the return, tracking, round, and pointing flight functions can be operated normally; 1 bar (flashing state) means that the drone is currently in a low battery state, and the drone will perform the automatic return to home function; in the low battery state, there is no tracking, round, or pointing flight function; the maximum flight distance is 20 meters, and the maximum flight altitude is 20 meters.

• GPS Signal
  Show the current altitude, distance, and corresponding latitude and longitude of the drone from the home point.

• Emergency landing
  You can make an emergency landing when the drone gets out of control.

• Lens switch
  The front lens and the lower lens can be switched.

• VR Mode
  Click for VR Mode.

• Flight record
  Records the relevant parameters of each flight;

• Album
  Check photos and videos.

• Parameter
  The beginner mode and the parameter adjustment mode can be switched.

• Joystick ON/OFF
  Tap to switch between mobile phone control or remote control.

• Speed switch
  Shows the current fast and slow status. Click on the mobile phone control mode to switch the fast and slow status.

• Photo/Video
  Switch to Photo/Video
  Click to take photos and video according to the current lens (front lens or bottom lens). When taking a picture, the indicator lights on the body flash once; when recording, the indicator lights flash twice continuously. When recording, resolution of videos on the mobile phone is 720P and resolution of videos in the storage card is 1080P.

• Motors Unlock
  After unlocking, click to achieve one-key take-off or one-key descent.

• Take-off/landing
  After unlocking, click to achieve one-key take-off or one-key descent.

• Front camera gimbal controller
  After the drone takes off, the front camera gimbal controller will be displayed on the left side of the screen. At this time, if you move the slider of the controller upwards, the front lens of the drone will move up a certain angle; if you move the slider down, the front lens of the drone will move a certain angle downward.

• Flight posture
  Show the flight posture change, relative position and direction change of the drone. The center of the white circle indicates the position of the operator, the white triangle tip indicates the direction of the drone’s head; the offset of the white triangle indicates the left and right offset of the drone relative to the operator.

• Auto Return To Home
  Click in GPS mode and automatic return to home will be performed.

• Master- Tracking
  In the optical flow mode, click “master tracking”, a blue circle pops up to indicate the target is detected, select the blue circle and click to confirm then it will turn red, when the target is lost, the indicator light will turn yellow. In master tracking mode, the drone will automatically fly back when you open your both arms, and the drone will automati-cally move forward when you retract your arms.

• Palm -Control
  In the optical flow mode, click the palm control, a blue circle pops up to indicate that the target is detected. Select the blue circle and click to confirm and it will turn into a red circle. At this time, the rear indicator light of the drone turns red. When the target is lost, the indicator turns yellow.

• GPS- Tracking
  In GPS mode, the drone will head in the direction of the mobile phone and follow the mobile phone to move. The minimum distance of GPS tracking is 5 meters. During GPS tracking, operations such as ascent, descent, forward, backward, and left and right flying can be performed.

• Round Flight
  In GPS mode, the drone will circle clockwise or counterclock-wise around the current position of the drone. The minimum radius of the orbiting flight is 5 meters, and the ascent, descent, forward and backward can be controlled during the orbiting process.

• Trajectory flight
  In the optical flow mode, the drone will fly according to the selected position.

• Waypoint Flight
  In the GPS mode, the drone will fly according to the selected position. When the drone altitude is lower than 15 meters, the drone will automatically rise to 15 meters before performing waypoint flight. When the drone altitude is higher than 15 meters, the drone will perform directly waypoint flight.

Before using the smart app features, see Loolinn Air App User Manual for further information)
Ensure that you pre-configure the flight altitude and distance in the Loolinn Air App.

Understanding the drone LED indicators

flow positioning
2| Front indicator = constant white, rear indicator = constant green| GPS mode
3| Front and rear indicators flash once every 4 seconds| Headless mode
4| Front and rear indicators flash twice every 1.5 seconds| Recording in progress
5| Front and rear indicators flash rapidly| Pairing or level calibration in progress
6| Front and rear indicators flash twice every second| Low battery
7| Front and rear indicators flash once every second| Signal lost
8| Front indicator = constant, rear indicator = flashing slowly| GPS fault
9| Front indicator = constant, rear indicator = flashing rapidly| Poor GPS reception

Troubleshooting

The drone does not respond.

| 1. Undervoltage protection was enabled.

2. The remote control battery level is low and the power indicator is flashing.

| 1. Charge the drone battery.

2. Change the batteries in the remote control.

The drone’s response is intermittent.| 1. The remote control batteries are nearly empty.

2. There is interference from a remote control on the same frequency.

| 1. Change the batteries.

2. Move to a different area where there is no interference.

The drone drifts to one side whilst hovering.| The drone is not calibrated level to the ground.| Calibrate the drone.
The drone does not travel in a forwards direction in headless mode.| ****

The drone was involved in a collision.

| Reconfigure the forwards direction.
The drone does not hover properly/the drone keeps moving up and down.| 1. The drone is not calibrated level to the ground.

2. The air pressure is unstable due to poor weather conditions.

3. A violent collision corrupted the gyroscope’s data.

| ****

1. Calibrate the drone.

2. Avoid flying in poor weather.

3. Calibrate the drone.

Accessories (available separately)
The following section contains a list of optional accessories that are available to purchase. Accessories can be purchased from the seller.

Warning :
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE :
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

“This device complies with FCC radiation exposure limits set forth for general population (uncontrolled exposure).This device must not be collocated or operating in conjunction with any other antenna or transmitter.”

• RF frequency band :2409-2475MHZ
• Transmitter power : -3.73dBm (Max.)
• product name: [GPS BRUSHLESS DRONE]
• model number : [Z6 Pro]
• Brand name :Loolinn

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>