BARNES4WD B4WK12706 Bronco Rear Axle Upper Control Arm Brackets Instruction Manual
- June 15, 2024
- BARNES4WD
Table of Contents
BARNES4WD B4WK12706 Bronco Rear Axle Upper Control Arm Brackets Instruction
Manual
Thank you for purchasing our Bronco Rear Axle Upper Control Arm Brackets!
Installation Notes:
- The brackets are designed to fit a 2021-Current Bronco
- These brackets will not fit a Bronco Sport
- Removal of the factory brackets is required for installation.
- Refer to your factory service manual on removal of any factory components.
Tools required:
- Proper Cutting Tool (Grinder, Plasma Cutter, Torch)
- Welder with at least .25” Capabilities
- Tape Measure
- Angle Finder
- 24MM Socket
- 10MM Socket
- 13MM Wrench
- Ratchet
Contents of box
Bill Of Materials for B4WK12706
QTY| Part Number| Etch Number| Description
1| B4W188975| 975B| Bronco Rear Axle UCA Bracket Passenger
1| B4W188976| 976B| Bronco Rear Axle UCA Bracket Driver
1| B4W125124| 124B| Bronco Rear Axle UCA Bracket Brake Line Tab Passenger
1| B4W125125| 125B| Bronco Rear Axle UCA Bracket Brake Line Tab Driver
1| .80CNFH0Z/934| NA| M8X1.25 hex nut class 8 zinc
Step 1:
Park the Bronco on a level surface, support the frame and remove the rear
upper control arms at the axle and any brackets connected to the lower control
arm brackets.
Step 2:
Locate the rear upper control arm brackets and remove them with a proper
cutting tool.
Step 3:
Weld each tab its correct bracket as shown below.
Step 4:
Place the Barnes4wd upper control arm brackets onto the axle the passenger
mount should be 5 1/8” from the flange of the center section and the driver
mount should be 15/16” from the opposite side of the center section as shown
below. The back face of the bracket should be 48° off the pinion.
Step 5:
Fully weld the brackets to the axle.
Step 6:
Reinstall the upper control arms into the brackets. Install any brackets that
were connected to the factory upper control arm brackets using the supplied
hardware.
Congratulations! You Have finished the installation of the Barnes 4wd
Bronco Rear Upper Control Arm Brackets.
Professional Services Disclaimer:
The content of all pages of this website (collectively, the “Website”), such as text, graphics, images, information and other material (collectively, “Content”) is for informational purposes only. Any information furnished on this Website is not intended nor implied to be automotive advice and is not intended to replace personal consultation with a qualified automotive service technician, mechanic, or similar automotive professional.
Barnes 4WD has not examined the Content for accuracy, timeliness, completeness, appropriateness, or helpfulness. Barnes 4WD does not endorse any specific tests, products, procedures, opinions, or other information that may be mentioned on this Website. Your reliance upon information and Content obtained by you at or through this Website is solely at your own risk. IN NO EVENT SHALL BARNES 4WD BE LIABLE OR
OTHERWISE RESPONSIBLE FOR ANY DAMAGE OR INJURY (INCLUDING DEATH) TO YOU, OTHER PERSONS, OR PROPERTY ARISING FROM ANY USE OF ANY PRODUCT, INFORMATION, IDEA, OR INSTRUCTION CONTAINED IN THE CONTENT. BARNES 4WD DOES NOT MAKE ANY REPRESENTATION OR WARRANTY, EXPRESS OR IMPLIED, AT LAW OR IN EQUITY, WITH RESPECT TO ANY PRODUCT FEATURED ON THE WEBSITE, INCLUDING WITHOUT LIMITATION WITH RESPECT TO MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, VALUE, VALIDITY, OR ENFORCEABILITY, AND ANY AND ALL SUCH OTHER REPRESENTATIONS OR WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>