SPLITSKY CH-07 Digital Alarm Clock for Bedroom User Manual

: June 15, 2024
: SPLITSKY

SPLITSKY CH-07 Digital Alarm Clock for Bedroom

RGB Color Changing Clock

Specifications

Model : CH-07
Power Input : Type-C 5V
Power Output : USB
Battery : CR2032

Product Information

The RGB Color Changing Clock, model CH-07, is a versatile alarm clock that features a color-changing display, alarm functions, FM radio, and USB charging capabilities. With its sleek design and intuitive button interface, the clock offers a user-friendly experience. It comes with a Type-C data line for power input and a USB output for charging your devices.

Safety Instructions and Product Preservation

Please follow these safety precautions and maintenance guidelines to ensure the longevity of your RGB Color Changing Clock

Use a dry soft cloth to clean the product. Avoid using abrasive cleaners, mats, or cleaning solvents such as alcohol or acetone, as they may damage the surface.
If the clock is not in use for a long time, unplug the USB cable and store it in a safe and dry place, away from any potential damage.

Package Contents

The product package includes

Illusory Color alarm clock x 1
Type-C data line x 1
Instruction manual x 1

Product Appearance & Button Introduction

The clock features the following buttons

Alarm 1 switch / setting
Screen brightness adjustment / time setting
Voice reduction / next channel on the radio
Alarm 2 switch / setting
Time display font color switch
Radio switch / automatic station search
Sound plus / previous channel on the radio
Drowsiness / accompanying sleep countdown / setting addition and subtraction / radio FM
Alarm 1 mode switch
Type-C 5V power input
Alarm 2 mode switch
USB output
Type-C output

Pre-Use Setting
To set up the RGB Color Changing Clock before use, follow these steps

Power On for the First Time
Connect the Type-C cable to the connector on the side of the alarm clock, and plug the other end of the USB cable into a USB power source.

Install the Battery
The alarm clock comes with a pre-installed CR2032 battery. Simply pull down the insulation sticker to activate the clock.

Time Setting
When powered on for the first time, the clock will display AM 12:00. To set the time

Long press the TIME SET button to enter the clock setting mode.
To set Alarm 1 (as an example), press and hold the corresponding button. The clock will flash, indicating that it is in alarm setting mode.
Rotate the big round key to adjust the alarm time.
Click the button to confirm and enter the minute setting. Rotate the big round key to adjust the minutes.
Click the button to confirm and select the alarm sound by rotating the big round key. The available options are S01-S08, representing different sound effects.
Click the button to confirm and enter the volume adjustment mode. Rotate the big round key to adjust the volume. The screen will display V01-V16, indicating the volume level (16 segments in total).
Click the button to confirm and exit the alarm setting. The process is the same for Alarm 2.

Alarm Switch
To switch the alarm on or off, simply click the corresponding button while in the time display state.

Alarm Mode Selection
When the alarm is on, you can toggle the switch to adjust between daily alarm, weekday alarm, and weekend alarm settings.

FAQ (Frequently Asked Questions)

Q: How do I clean the clock?
A: Clean the clock with a dry soft cloth. Do not use abrasive cleaners or solvents.
Q: Can I use alcohol or acetone to clean the clock?
A: No, using alcohol or acetone may damage the surface of the clock.
Q: How do I store the clock when not in use?
A: If not in use for a long time, unplug the USB cable and store the clock in a safe and dry place, avoiding any potential damage.
Q: What is included in the package?
A: The package includes the Illusory Color alarm clock, a Type-C data line, and an instruction manual.
Q: How do I adjust the screen brightness and set the time?
A: Use the corresponding buttons for screen brightness adjustment and time setting. Refer to the button introduction section for more details.
Q: How do I set the alarm?
A: Long press the corresponding alarm switch/setting button, then follow the instructions in the alarm setting section.
Q: Can I set different alarms for Alarm 1 and Alarm 2?
A: Yes, Alarm 1 and Alarm 2 can be set independently.

Safety instructions and product preservation

Safety precautions
To reduce the risk of fire, electric shock or injury, please read these instructions before use.

This product is for family use only, including similar places such as hotels.
Please place this product on a stable, horizontal, non-slippery surface.
Do not use this product in wet environments, such as bathrooms, showers or near swimming pools.
Do not let water into the product or splash any water on the product.
Use only the original USB cable provided.
Do not use this product as a means to reduce sleep time. This product is designed to help you wake up.

It’s easier than reducing your need for sleep.

Maintenance

Please clean the product with a dry soft cloth.
Do not use abrasive cleaners, mats or cleaning solvents such as alcohol or acetone, as this may damage the surface of the product.
If the product is not in use for a long time, unplug the USB cable and store the product in a safe and dry place without being squeezed, hit or damaged

Objects the package contains

This product is packed in a color box, which contains a Illusory Color alarm clock X1, Type-C data line X1 and instruction manual X1.

Product appearance & button introduction

Alarm 1 switch / setting
Screen brightness adjustment / time setting
Alarm 2 switch /setting
Time display font color switch
Voice reduction / next channel on the radio
Radio switch / automatic station search
Sound plus / previous channel on the radio
Drowsiness / accompanying sleep countdown / setting addition and subtraction / radio FM Product appearance introduction
Alarm 1 mode switch
Type-C 5V power input
Type-C output
⑩ Alarm 2 mode switch
⑫ USB output

Pre-use setting

Power on for the first time
Connect the Type-c cable to the connector on the side of the alarm clock and the other end of the USB cable is connected to the USB female chassis. As shown in the picture below

Install the battery
The alarm clock comes with a pre-installed CR2032 battery, and just pull down the insulation sticker. As shown in figure 2

Time setting

When powered on for the first time, the time shows AM 12:00

Long press TIME SET to enter the clock setting
In the time display state, long press the TIME SET key to enter the clock setting, the clock will blink, rotate the top big circle key to set the current clock.
Click the TIME SET button to confirm to enter the minute setting
Click the TIME SET button to confirm, enter the minute setting, and also rotate the top big circle key to set the current minute.
Click the TIME SET button to enter the 12/24-hour setting
Rotate the top big circle key to set 12/24 hours.
Click the TIME SET button to enter the week setting
Rotate the top big circle key to set the week. When the setting is complete, click the TIME SET button to confirm and exit the time setting.

Note 1 : in the time setting state, press the TIME SET button for a long time to exit the time setting.
Note 2 : if you choose the 12-hour system, the AM/PM will be displayed.

Alarm setting (take alarm 1 as an example)

Press the button long to enter the alarm 1 setting
Press the button ****for a long time, the clock will flash, and rotate the big round key to adjust the alarm clock.
Click the button to confirm
Click the button ****to confirm and enter the minute setting, and rotate the big circle key to adjust the minute.
Click the button to confirm
Click the button ****to confirm and enter the alarm sound selection, rotate the big round key to select the alarm sound, and display S01 S0 8 01 0 8 is the change value, corresponding to different sound effects)
Click the button to confirm
Click the button ****to confirm and enter the volume adjustment, rotate the big round key to adjust the volume, and the screen displays V01 V16 (a total of 16 segments)
Click ****to comfirm and exit the alarm setting (alarm 1 is the same as alarm 2).

Note : the setting of alarm clock 2 is the same as taht of alarm clock 1.
Long press the button ****in the alarm clock setting interface to exit the alarm clock setting mode.

Alarm switch

Alarm switch
In the time display state, click , switch the
User prompt
Alarm 1 and alarm 2 operate in exactly the same way.

Alarm mode selection

When the alarm is on, toggle the switch and adjust the daily alarm, weekday alarm and weekend alarm in turn, as follows

One button for sleepy & turn off the alarm clock & no operation

After the alarm clock is turned on, the alarm clock will be turned on at the preset time: when it comes to the alarm clock setting time, the alarm clock will start to ring and wake you up. When the alarm goes off, you can do the following

Sleepy
Click the sleepy button when the alarm is loud, enter the sleepy mode, the screen displays and
flashes the sleepy icon, and the sound will turn on again after 9 minutes.
Note : the number of drowsiness is unlimited.
Stop this time.
When the alarm goes off / sleepy, click the key of the corresponding alarm to stop this alarm and not affect the next alarm.
When unmanned
When the alarm goes off 20MIN without any operation, this alarm will be stopped automatically, and the next alarm will not be affected.

Illusory Color font display mode

Illusory Color display adjustment
In the time display state, click COLORS to toggle the display font color (white, red, green, blue, gradient, magic color, left and right graduality, up and down graduality)

Screen brightness control

Screen display brightness adjustmen t
Click the DIMMER button and the screen brightness changes from bright to dark ( gear 4, gear 3, gear 2, gear 1, OFF).
Note : bright color mode 1 is brighter, monochrome mode 1 is darker and can be seen in darker environment.

Countdown to sleep

Sleeping companion switch
In the time display interface, click the big circle key to start the countdown, the countdown time flashes 5s, rotate the big circle key to adjust the countdown time, set the range (10 120, 180 240MIN)
Countdown companion sleep
When the countdown is turned on, the radio will be turned on automatically. When the radio is turned on, it will be turned off synchronously after the countdown is over; (you can also turn on the radio and then turn on the countdown)
Check the length of sleeping
After the countdown companion sleep function is turned on, click the big circle key to check the remaining companion sleep time.

FM radio adjustment

```
1.  **FM switch**  
```
In the time display screen, click the key to turn the FM radio on / off.
FM automatically searches the station
When FM is on, press the long button to enter the FM automatic search mode, search range 76.0MHZ~108.0MHZ, and automatically play the first found radio frequency after the search is completed.
FM radio channel adjustmen t
After FM is turned on, long press the key for 2s to switch to the up / down radio channel.
FM volume adjustment
When FM is on, click the key to adjust the current radio volume.
Frequency adjustment of FM radio
When FM is on, rotate to adjust the current frequency 0.1MHZ.

Replace the battery

Unscrew the battery cover with a screwdriver, remove the battery cover, put the battery into the battery box, install the battery cover, and tighten the screws.