Baseus Blade2 Fast Charging Bank with Digital Display 12000mAh 65W User Manual

User manual

Blade2 Fast Charging Bank with Digital Display 12000mAh 65W

Baseus Blade2 Fast-Charging Power Bank with Digital Display Intelligent Edition 12000mAh 65w
Please read this user manual carefully before use and keep for future reference.

Warnings

Improper use of the product may lead to battery malfunction or severe overheating, and may even cause fire or explosion.
To avoid any damage to thd and your property, please follow the instructions below when you use and store the proe uct.

1. This is NOT a toy! Please place this product in areas that are not easily accessible by children. Do not allow children to operate this product, or accidents may occur.
2. Please change this product with a cha per approved by the local safety standards in case of danger or damage.
3. DO NOT apply pressure, and avoid collisions. The battery and circuit may be damaged if this product falls from a great height, experiences intense shacks, or is immersed in liquid, if so, please avoid using this product.
4. If this product suffers from deformation, leakage, or radical decline in performance, please stop using this product.
5. Please DO NOT charge any device or recharge this product in places that may affect its heat dissipation, such as pants pockets, enclosed bags, beds, or couches. And ensure this product is not under any cover when operating, When charging other devices for prolonged periods, DO NOT stack any device on top of this product, or it might affect its heat dissipation.
6. This product CAN NOT be disassembled, applied pressure, pierced, short-circuited, immersed in liquid, disposed of ina fire, or exposed to a high temperature or heat source with a temperature greater than 140°F(60°C).
7. DO NOT place this product in areas with extremely high temperatures, Such as under direct sunlight or in a vehicle with a very high interior temperature.
8. This product contains lithium batteries, OO NOT disassemble it! Or danger or battery damage may occur.
9. This is not domestic waste. It should be handed over to a designated facility for electronic device recycling,

Attention

1. Please fully charge this device before using it for the first time.
2. The power banks have conversion efficiency, so the battery capacity of power bank is not equal to the rechargeable Capacity.
3. Please choose an appropriate charger for recharging this product and suitable cables when charging other devices.
4. Please ensure some supervision is in progress when recharging this product, DO NOT chai ree this product without any care.
5. Please femove the cable when done recharging this product or finished charging for any other device to preserve the product integrity.
6. If the indication does not light up after pressing the power button, please recharge this product.
7. Please preserve this product with a battery percentage between 25%-50% for long-term storage. Place this product ina cool and dry environment. To slow down battery aging, avoid storing this product in an empty or full charge for long-term storage.
8. Please do not dismantle the product by yoursetf. Improper use or placement may compromise the service life or damage the product, to which our company will not bear any legal responsibilities nor offer any guarantee. Please understand.

Caution

1. This product does not contain any user-serviceable parts, and the rechargeable battery is not replaceable.
2. Putting the battery pack into fire or heating it in an oven, as well as subjecting the battery pack to mechanical squeezing or cutting, may result in explosion.
3. Placing the battery pack in an extremely high-temperature environment may cause explosion or leakage of flammable iquids or gases.
4. Subjecting the battery pack to extremely low air pressure may cause explosion or leakage of flammable liquids or gases.

Specifications

Content

Power bank X1
Charging cable X 1
User manual 1
Warranty card X 1
Storage bag x 1

Product Schematic Design

1. Power switch
2. Type-Cl input/output
3.  Type-C2 input/output
4. LED display

Description

This product is a digital fast-charging power bank built on industry-leading digital power technology architecture, equipped with a Bluetooth management function. It features a built-in digital display screen that shows real-time status of the power bank, including remaining battery percentage, cell temperature, input/output power, remaining usage time, and various function icons (such as Bluetooth connection status, countdown timer, low current mode, timer). It can also update the current mood status on the display screen in real-time through the Baseus app (only supports Chinese/English display). This product supports 60W input, 65W output, with dual input and dual output, compatible with multiple fast charging protocols including PD3.0, QC4+, QC3.0, FCP, Samsung AFC, etc. It also has built-in multiple safety protection circuits, such as overcurrent, overvoltage, over-temperature, and short circuit protection, making it suitable for fast charging laptops and phones.

Instructions

Note: The product uses Bluetooth to connect with the phone. When the distance is far (greater than 10 meters), the app may not respond immediately or provide specific prompts for related status. It is recommended to stay close to the product for a better user experience.

Power On

In idle mode, press the power button once to display the remaining battery power. After approximately 30 seconds, the screen will go into screensaver mode. If there is no operation after approximately 30 seconds, the product will automatically turn off the output.

When a device is connected for charging or discharging, the working status and voltage current values of each port will be displayed individually. When charging the power bank using a charging cable, the corresponding port will display relevant voltage and current information, with a lightning icon displayed above the port information.
When using the power bank to charge other devices, only the discharge voltage and current are displayed, without any icons,
Display

| Discharge: Remaining usage time of the power bank.
Charge: Time taken to fully charge the power bank.
---|---
| Low-current mode: Enable through the Baseus app or double-click the button, allowing customization of shutdown time within a maximum of 4 hours, with the device remaining on within this time frame.
| Timer activation: Enable through the Baseus app, allowing customization of timed reminders within a maximum of 24 hours, requiring the device to remain in the on state.
| Countdown shutdown activation: Enable through the Baseus app, allowing customization of auto-shutdown within a maximum of 24 hours. The device has to remain in the on state.
| Device abnormal alert: Indicates device malfunction. Automatic recovery can be attempted according to prompts. If unable to recover, please contact customer service for assistance.
|  Bluetooth device connected.
| Battery level remaining.
| Lightning icon: indicates that the power bank is currently being charged, and displays the current charging voltage and current.
| No lightning icon: indicates that the power bank is currently discharging to an external device, and displays the current discharging voltage and current.

Baseus App

1. Press the power button to turn on the power bank. The Bluetooth is in broadcasting mode. Click on the “+” button in the Baseus app at the top right comer to add a product.

2. Select the “Blade 2″ product, click on “add device”, and complete the addition.

3. Click on the theme to set the screen display background color and customize mood text, with a limit of 20 characters in Chinese or English, including punctuation marks.

4. Click on the timer function to access quick settings or customize reminders within 24 hours; click on the countdown shutdown to perform quick or customized shutdown tasks within 24 hours, automatically turning off the mobile power output.
   Note: All of the above tasks need to be performed while the power bank is turned on.

5. After activating the low current mode, the device will remain powered on for up to 4 hours.

6. When the low current mode, timer mode, and countdown shutdown task are active simultaneously, the countdown shutdown task will take priority.

Operating Environment

Operating temperature: non-tropical area, 0°C to 25 °C
Storage temperatures: 0°C to. 40°C

Icon Description

The 5-year icon refers to the “valid period for environment-friendly use”, not the product quality assurance period. All electronic products contain toxic and harmful substances such as lead, mercury and cadmium. The overdue use of these
products may lead to leakage or mutation of these toxic and harmful substances, causing enviranment pollution or serious damage to people and property. The term of ““environment-friendly use period” means that all electronic products shall be used within this validity period. We won’t be held liable for safety issues caused by using of the product beyond its safe service life.

Statement on Toxic and Hazardous Substances in Electronic Information Products

This form is compiled in accordance with SJ/T 11364.
O: Indicates that contents of the toxic and hazardous substances in all homogeneous materials are below the limit requirements specified by GB/T 26572 standard.
X: Indicates that contents of the toxic and hazardous substances exceed the limit requirements specified by GB/T 26572 standard in at least one homogeneous material of the component.
Baseus App Download and Guide

Scan the QR code on the right with your mobile device to obtain the download address, or enter https://www.baseus.com/#/home(Chinese)/
https://us.baseus.com/download (other languages) in the browser address bar to download the app.
Please register and log in according to the instructions in the app, and refer to the guides to add products for connection and operation.

https://bds-api- cn.baseus.com/app/official/download

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>