Paris Rhône Miroir Baby Monitor PE-IH004 User Manual

: June 15, 2024
: PARIS RHÔNE

Paris Rhône Miroir Baby Monitor PE-IH004 User Manual

Paris Rhône Miroir Baby Monitor PE-IH004

Model: PE-IH004
Miroir Baby Monitor
User Guide

SAFETY INSTRUCTIONS

Keep cord out of the reach of children (more than 3ft / 0.9m owoy) in case of STRANGULATION.

NEVER place the camera or cord in or near the crib or playpen.
NEVER mount the camera directly above the crib or playpen to avoid the risk of injury.
Only use the AC adapters provided.
Never use the unit near water, including near a bathtub, sink, laundry machine tube, wet basement, etc.
Do not install near any heat sources such as radiators, heat registers, stoves, or other devices that produce heat.
Only use attachments and accessories specified by the manufacturer.
Unplug this device when unused for long periods of time.

CAUTION

NOT toys. Do not allow children to play with them.
This product is NOT intended to replace the proper supervision of children. You MUST check your child’s activity regularly.
This product is not intended for use as a medical camera and its use should not replace adult supervision.
Unplug the product during lightning storms.
Please check the operating range and condition of the camera carefully at the initial installation, and on a regular basis after that.
Check the reception regularly. Test the camera before use and after changing the camera’s location.
For indoor use only.
Clean the camera with a dry cloth only.
Do not block any ventilation openings.
Microphone feedback might occur when the monitor is too close to the camera. Please keep them at least l.Sm / 4.9ft apart.

PACKAGE CONTENTS

Baby Monitor & Camera
AC Power Adapter *2
Mount Kit
Camera Mount
Power Cable *2
User Guide

PRODUCT DIAGRAM

Baby Monitor

1. Power/Sleep Button: Long press to turn on/off the monitor; short press to turn on/off the screen.
2. Menu/Back Button: Press to enter menu page or press as a Back
3. Camera switching: switching and polling of multiple cameras.
4. Charging indicator: the monitor emits a yellow light when charging, and turns off when fully charged.
5. Left Button: Press to pan the camera leftward or to change your selection leftward.
6. Up Button: Press to tilt the camera upward or to change your selection upward.
7. Confirm/Zoom Button: Press to Zoom in/out or to confirm your selection.
8. Right Button: Press to pan the camera rightward or to change your selection rightward.
9. Down Button:Press to tilt the camera downward or to change your selection downward.
10. Power Indicator: The green light turns on if connected to electricity.
11. Call key: long press to talk to the baby on the monitoring screen; short press to adjust the sound or brightness of the display; short press next time to enter the lullaby play page.
12. Auto-split: Camera view switch and binary screen switch shortcut button.
13. Sound Level LED: Low/high level shows low/high sound detected by the camera.
14. Low battery indicator: Low power indicator: when the display is in low power state, the red light flashes.
15. Monitoring Status Indicator: Green. When the camera is discon nected, it flashes slowly; when it enters pairing mode, it flashes quickly; when the camera is turned on, it is always on.
16. Microphone
17. Antenna
18. Support Stand
19. Speaker
20. Power Input
21. Reset Hole

Camera

1. Night Vision Sensor
2. Camera Lens
3. LEDS
4. Microphone
5. Antenna

6. Speaker
7. Pair Button
8. Power Input
9. Temperature Sensor
10. Wall Mounting Threaded Holes

GETTING STARTED

1. Charging & Powering Baby Monitor

Connect the monitor adapter to the monitor and a power outlet.
Unplug the unit when its power indicator turns off, indicating a full charge.Of course, if you have been plugged in, it will not affect the use, but it may affect the battery life.
Press the Power button on the monitor to power on with the power indicator lighting green.

2. Powering Camera

Connect the camera to power source via the Type-C cable and camera adapter.

WARNING:

• Only use the power adapters included in the package.
• Do not place the camera and power cord within the reach of your baby.

3. Pairing the Baby Monitor & the Camera

By default, one camera has been paired with the monitor when manufactured. When you power on the monitor and camera, the two will automatically pair.

To odd more cameras.

Step 1:

1. Press to enter menu page.
2. Choose and press button.

Step 2:
1. Select then press button.

Step 3:

1. Select and press button TWICE.
See Camera is NOT paired.
2. Press button to start pairing.

Step 4:

1. Press PAIR button on the back of the camera.

2. Then the monitor will auto-pair with the camera.

WARNING:

Once they’re paired successfully, the camera number with icon ‘fl will be shown at the top left.
It is recommended to pair in the baby’s room, or wherever you intend to place the camera.
Microphone feedback might occur when the monitor is too close to the camera. Please keep them at least 1.5m / 4.9ft apart.
Four cameras at most can be connected to one monitor.

4. Placing the Camera

For safety reasons and better vision in night vision mode, if the camera is placed on a 0.75m / 2.5ft table top, the distance from the baby is at least 1.5m / 4.9ft. ( The effective distance between the camera and the baby is within 6m / 19.7ft. In the meantime, please ensure that the camera power cord cannot be touched by the baby.)

Placing the Camera

5. Wall Mounting Camera

Unscrew bracket’s nut and adjust the bracket to an appropriate angle.
Screw the nut again tightly.
Drill holes on the wall and put green ribbed plastic anchors into holes with a hammer.
Fix the bracket on the wall by screwing its screws into the ribbed plastic anchors.
Screw up the top bolt of bracket with the nut at the bottom of the camera.
To better match the proper viewing field, Please unscrew the nut on the side of the bracket, adjust the angle of the bracket downwards, until the baby appears in the monitoring range, tighten the nut on the side of the bracket again, and the installation is complete.

Mounting Camera

WARNING: Don’t release the camera until you’re sure it is firmly mounted

FUNCTIONS & OPERATIONS

Top Status Indications

Status Indications

Notifications Icons

WARNING: You can open Live-Video-Loop function through shirt presses on the CAM button until you seer) on the status bar. When Live-Video-Loop function is on, the connected cameras will automatically switcn every 10 seconds. And if there is o sound/temperature alarm, the camera-switch function will pause temporarily.

1. Volume Adjustment

Use Shortcut Button: Press TALK Button ->Left/ Right Button to quickly adjust the volume with icons.

2. Display Brightness Adjustment

Use Shortcut Button: Press TALK Button ->Up/ Down Button to quickly adjust the volume with icons.

3. Talkback

Press and hold TALK Button to talk to your baby, release it to exit the talking mode.

WARNINGS:

When you ore in the monitoring mode, press and hold the TALK key to enter the intercom mode, and the icon will be displayed on the monitor. When you enter the menu, the intercom function con still be used, but the icon will not appear on the screen.
When it’s mute or the speaker volume is too low, you may not be able to hear the baby.
When you’re pressing the Tolk Button, the camera will not transfer the sound to the monitor. Please release the button to listen to your boby.

4. Add Camera

Step 1:

1. Press to enter menu page.
2. Choose and press button.

Step 2:
1. Select then press button.

Step 3:

1. Select and press button TWICE. See Camera is NOT paired.

2. Press button to start pairing.

Step 4:

1. Press PAIR button on the back of the camera.
2. Then see the prompted Paired.

WARNING: Four Cameras at most con be connected to one monitor.

5. Delete Camera

Step 1:

1. Press to enter menu page.

Choose and press button.

2. Select the camera need deleting.

Press button.

Step 2:

1. Select the right camera icon.

Press button TWICE.

2. See Deleted. Your camera is deleted.

6. Camera interaction and loop

Note: Connecting multiple cameras is ovoiloble.
Multiple cameras are powered on and within the monitor connection range.

Step 1:

1. Confirm that the camera channel page is connected to more than two cameras

Step 2:

1. Check the camera channel, click CAM , the monitor screen will switch to the next camera.

Step 3:

1. After all the camera pages have been switched, click the CAM camera channel icon to display the loop icon, and all camera screens will be polled and played every 10 seconds, with images and sounds.

Step 4:

1. Click CAM again to exit the screen polling. The camera screen returns to the current polling screen.

7. View camera

Note: At least two cameras must be connected. Multiple cameras have been powered on and are in range of monitor connections.

Camera switching and polling

Step 1:

1. Press to enter menu page.

Choose and press button.

2. Select the camera you want to switch.

press button.

3. You need the camera to poll for playback. Choose and press button.

Open the binary screen

Step 1:
1. Press to enter menu page.

Choose and press button.

2. Select the camera that needs split screen, press to switch to and then click button.

3. 1. Select another camera to split the screen and repeat Step.
2. The split screen is successful.

WARNING:

Shortcut keys: short press AUTO-SPLIT button to enter this page, press twice to return to the video page.
If you need to return to the video page, please press twice or wait 30 seconds to return .

8. VOXmode

Explanation:

1. There are three options of sound detection, LOW(78dB), MEDIUM(65dB) and HIGH(60dB). LOW means the sound can be detected if it reached 78dB, and so on for MEDIUM and HIGH.
2. Setting “off” turns off the alarm sound in VOX made.

Step 1:
1. Press to enter menu page.

Choose and press button.

2. Select the option you want.

Press button.

WARNING: If you need ta return to the video page, please press twice or wait 30 seconds to return.

9. Temperature Alarm

Explanation :

indicates that the temperature value for high and low temperature alarms can be set.

Step 1:

1. Press to enter menu page.

Choose and press button.

2. Select the option you want.

Press button.

WARNING:

A vox / temperature alarm con be temporarily turned off by pressing any button on the monitor.
If you need to return to the video page, please press M;:u twice or wait 30 seconds to return.

10. Feeding

Explanation:
This function is to remind you of feeding your baby. OFF means you shut down the function; 2 hour means it reminds you every 2 hours and so on for the other options.

Step 1:

1. Press to enter menu page. Choose and press button.

2. Select the time you want. Select OFF to turn off the feeding reminder.

WARNING:

Selecting will set the alarm to the specified time.
If you need to return to the video page, please press twice or wait 30 seconds to return .

11. Lullabies

Explanation:

This function is to comfort baby when needed.

Step 1:
1. Press to enter menu page .
Choose and press 0t button.

2. Select the lullaby you want. Select to play the lullabies in a loop.

WARNING:

If you need to return to the video page, please press twice or wait 30 seconds to return.
Shortcut keys: short press TALK twice to enter this page, press to return to the video page.

12. SCREEN SLEEP

Explanation:

This function is to prolong your monitor’s runtime by shutting down the screen.

Step 1:
1. Press to enter menu page.
Choose and press 0t button.

2. Select the time you want.

WARNING:

The screen will automatically light up if there is a vox alarm or a temperature alarm.
If you need to return to the video page, please press twice or wait 30 seconds to return.

13. Settings

Explanation:

This is a submenu of the function page, which can set screen sound and brightness, system sound, time and date, system language, system reset, and provide service support information.

Step 1:

1. Press to enter menu page. Choose and press button.

2. Select the function to be adjusted.

Brightness

Step 1:

1. Choose and press button.

2. Adjust monitor screen brightness.

If you need to return to the video page, please press twice or wait 30 seconds to return.

Volume

Step 1:

Choose , and press button.

2. Adjust the monitor volume.

WARNING: If you need to return to the video page, please press twice or wait 30 seconds to return.

Alarm

This function is to adjust the monitor side system sound.

Step 1:
1. Choose , and press button.

2. Select the option you want. press button.

1. ln vox mode, set • silent • , the alarm sound under vox will not be turned off
2. lf you need to return to the video page, please press twice or wait 30 seconds to return.

Date/Time

Step 1:

1. Choose and press button.

2. stands for finishing the setting.

Language

There are two languages built in your device, you can choose your language here.

Step 1:

1. Press to enter menu page.

Choose and press button.

2. Select your language and press button.

WARNING: If you need to return to the video page, please press twice or wait 30 seconds to return.

Contact Us

Step 1:
1. Select

Press to enter the interface.

2. Contact Us.

Pess to return.

If you need to return to the video page, please press twice or wait 30 seconds to return.

Restore factory settings

Step 1:

1. Select .

Press to enter the interface.

2. Conform YES to reset. Press or conform NO to exit.

SPECIFICATIONS

Monitor

Resolution	IPS (1920 x 1080), PPl=400
Connectivity	2.4GHz FHSS
Image Aspect	16:9 (1080P)
Image Compression	H.264 (frame rate = 15fs)
Operating Range (No interference)	280-300m (antenna vertically placed at 90°

Camera

Cmos	1080P(1920×1080), 2.0M, 1/2.9″
Image Compression	H.264 (frame rate = 15fs)
Connectivity	2.4GHz FHSS
Power Input	5V / 2A (Type-C cable)
Pan-n-Tilt	100 degrees vertical (Up=90°, Down= 10°)

TROUBLESHOOTING

Product not powering on?| · Check that the camera and monitor are turned on.
• Check the camera and make sure it is well plugged into the outlet.
• Check that the monitor is of enough battery (When the battery level icon flashes red slowly on the display, it will automatically turn off in about 10 minutes).
---|---
Baby monitor can’t connect with the camera?| · Check whether the camera is near the monitor (recommended to keep within 1.5-2m / 4.9-6.6ft).
• Check whether the monitor is of low battery. Charge it in time to restore good connection.
• Check whether the camera is well connected to power
• Check whether there are any large metallic objects including doors, refrigerators, mirrors, etc., are placed between the camera and monitor thus blocking the radio signals.
• Check whether there’s any other 2.4GHz product is used nearby like WiFi routers, microwave ovens, which may interfere the connection.
• If nothing above is involved, please retry to pair.
Nothing shown when I view a camera?| · Check all connections to the camera (power cable plugging and pairing).
Check whether the screen is in sleep mode. Press any button to awake it.
• Check whether the camera is within range of the monitor.
• Adjust the monitor antenna to vertical position for better signal transfer.
No sound from the monitor?| Check whether the system sound volume is set High or Low. It’ll be mute if set so.
Black and white pictures?| Night vision LED may be ON. Please turn on room lights to force it out of the night mode.
Choppy videos?| · Check whether the camera is near the monitor and that there’re no obstacles between them.
• Adjust the monitor antenna to vertical position for better signal transfer
Too much noise?| · Volume may be set too high. Press Shortcut Button-> Left Button to volume down.
· The camera and monitor may be put too close; keep them at least 1.5m / 4.9ft apart.

WARRANTY & CUSTOMER SERVICE

12 months warranty

Lifetime customer service (contacts on the monitor, or back cover of this User Guide)

FCC STATEMENT

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.

FCC 20cm Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

WEEE COMPLIANCE

Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in countries with separate collection systems)This marking on the product, accessories or literature indicates that the product and its electronic accessories should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal.