SEBSON IR_WAL_F PIR Sensor Light Switch Outdoor User Guide
- June 15, 2024
- SEBSON
Table of Contents
- SEBSON IR_WAL_F PIR Sensor Light Switch Outdoor
- Product Information
- Product Usage Instructions
- Overview
- Scope of delivery
- General safety information
- Instruction for installation
- Function of the motion sensor
- Detection area
- Connection
- Function test
- Technical Data
- Information for private households
- Cleaning
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
SEBSON IR_WAL_F PIR Sensor Light Switch Outdoor
Product Information
Specifications:
- Operating voltage: 220-240V AC 50Hz
- Maximum power consumption: Max. 1,200W Max. 600W
- Protection type: IP65
- Protection class: II
- Motion detection speed: 50cm
- Operating temperature: Not specified
- Humidity: Not specified
The IR_WAL_F is a motion sensor product designed for indoor or outdoor use. It is used to detect motion and control the activation or deactivation of connected devices. The product comes with safety features and technical specifications that must be followed for proper installation and usage.
Product Usage Instructions
General Safety Instructions:
- Danger: Installation of this product should be done by a professional in accordance with applicable electrical and safety regulations.
- Caution: Keep this product away from children and animals to avoid shocking hazards.
Function of the Motion Sensor:
The motion sensor is designed to detect motion within its detection range
and activate or deactivate connected devices accordingly.
Activation and Deactivation of the Motion Sensor:
- Danger: Installation of this product should be done by a professional in accordance with applicable electrical and safety regulations.
- Before mounting the product, carefully read and follow the safety instructions and technical specifications provided.
- The motion sensor can be activated or deactivated using the switch (refer to Fig.4b).
Detection Range:
The detection range of the motion sensor is not specified.
Connection of the Protective Earth (PE):
The protective earth should be properly connected according to the
electrical regulations and guidelines.
Sensitivity to Ambient Light:
The sensitivity to ambient light can be adjusted based on the amount of
light in the surroundings (range between 3 and 2000 LUX).
Time Setting (Delay):
The duration of the operating time can be gradually adjusted from
approximately 10 seconds to 30 minutes. The timer will restart if motion is
detected by the sensor before the set time elapses.
Function Test:
- Make sure the motion sensor is not covered or obstructed.
- Ensure that the detection area is not limited by objects such as large furniture.
- To set the detection range and perform a function test in daylight, rotate the knobs to the positions shown in the diagram.
- After a warm-up phase of approximately 30 seconds, the motion sensor will be activated.
- If no further motion is detected within the sensor’s detection area, the sensor will deactivate.
FAQ:
-
Q: What is the operating voltage for this product?
A: The operating voltage for this product is 220-240V AC 50Hz. -
Q: What is the maximum power consumption?
A: The maximum power consumption is 1.200W for connected devices and 600W for the motion sensor itself. -
Q: What is the protection type and class?
A: The protection type is IP65 and the protection class is II. -
Q: How can I adjust the sensitivity to ambient light?
A: The sensitivity to ambient light can be adjusted using the provided settings, with a range between 3 and 2000 LUX. -
Q: Can I perform a function test during daylight?
A: Yes, you can perform a function test during daylight. Ensure that the detection area is not limited and follow the instructions provided.
Thank you for choosing a product of SEBSON. Please read the instructions carefully and keep them for looking up before starting this product. A long and failure-free operation can only be guaranteed if the installation and start-up is done properly. Before starting up this product, please check for external damage. In case of visible external damage, we immediately dis-advise the start-up of this product!
Please remove all packaging material of this product before the first start-up and check the content for completeness!
Overview
Intended use:
This SEBSON motion detector has an IR sensor that detects the heat radiation
of moving objects and activates e.g. a connected light.
Scope of delivery
- 1 motion detector
- Screws for fixing (4 pieces)
- Dowels Ø 6mm (4 pieces)
General safety information
- Danger: The installation of this product may be done only by a qualified person according to the valid regulations for electrical installation!
- Danger: In case of damages or contact with water turn off this product immediately without tension and make sure that a restart is no longer possible!
- The danger of suffocation: Please keep this product away from children and animals. The packaging contains small parts that can be swallowed!
- Caution: Avoid overloading the device, an overload can damage the device or cause a short circuit! Therefore, please note the maximum power consumption in the technical data!
- The remodeling of this product is not allowed! The proper and safe functioning of the device can no longer be guaranteed if it is modified! In addition, this will invalidate the warranty claim!
- The manufacturer does not accept any responsibility for injuries or damage resulting from improper use of this product!
- Any other use than the description may result in damage to the product. So the dangers are such as electric shock, short circuit, fire, etc.
- We reserve the right to make changes to the product, the packaging, or the operating instructions as well as printing errors.
- This product is suited for indoor- and outdoor use.
- Protect the product from external damage, heavy dirt, moisture, and excessive heat!
- In order that the warranty claim does not expire please use only the supplied items. Repairs may only be done by an expert and only by using original spare parts!
- In commercial institutions, the accident prevention regulations of the professional trade association for electrical equipment and facilities must be adhered to.
Instruction for installation
Instruction for installation (Fig 5):
- Danger: Before installing please make sure that the circuit is interrupted! For installation, the work on the mains voltage is required. Please remove the associated mains fuse or deactivate the switch fuse! Check by using a voltage tester if the line is de-energized. Make sure that the current circuit will not be closed during the installation!
- Danger: The installation of this product may be done only by a qualified person according to the valid regulations for electrical installation!
- Attention: Before drilling the mounting holes, make sure that there are no gas, electricity, or water pipes at the drilling location that could be damaged by this!
- Please observe the safety instructions and technical data before installing this product!
- Note on installation:
- L: Live wire (black or brown)
- N: Neutral conductor (blue or grey)
- This device is only suitable for wall mounting!
- For optimum range, select the mounting height recommended in the “Technical Data”.
- 2 units in a parallel connection (see Fig.4a)
- Permanent switch-on of a connected device with an additional switch connected in parallel (see Fig.4b).
To ensure optimum sensitivity of the sensor, install the device in the room in such a way that the movements are transversely to the device. Movements that are directly to and from the device are less well detected. (see Fig. 2a):
The following environments or surfaces are not suitable for mounting, as they may impair the detection of thermal radiation (see Fig. 2b):
- Metal surfaces e.g. metal door frames
- In the immediate vicinity of electronic devices such as computers, monitors etc
- Heat sources e.g. radiant heaters, radiators or lamps
- In the vicinity of e.g. fume cupboards or fans
- Within the radiation range of luminaires (minimum distance from luminaires >50cm)
Function of the motion sensor
The sensor integrated in this device detects heat radiation from moving bodies, e.g. people or animals, and transmits this as an electrical impulse to a connected light, for example. This device then switches itself on. The detection of heat radiation can be limited by large furniture, glass panes or very high ambient temperatures of over 40°C, for example in summer.
Disabling and activating the motion detector:
- ON: Sensor deactivated-Connected device is switched on
- OFF: Sensor deactivated- Connected device is switched off
- PIR: Motion detector is activated after 30 seconds (warm-up phase)
Detection area
Detection area (Fig 3):
The detection range of the motion detector is approx. 10m and 190° (free
area) at a mounting height of 1-1,8m on the wall. In closed rooms, the
detection distance can be lower, according to room layout.
Connection
Connection of the protective conductor (PE):
Connection of the protective conductor (PE):
| When connecting a lamp with protective conductor contact, the protective
conductor must be bypassed from the supply line to the lamp with the aid of an
additional terminal in the in-wall socket.
Sensitivity when switching (with regard to the ambient brightness):
| This setting control can be used to regulate the switch-on sensitivity of
this unit depending on the ambient brightness (between 3 and 2.000 LUX).
Time setting (switching off delay):
| The duration of the operating time can be set continuously from approx. 10s to 30min. The timer is restarted if a movement from the sensor is detected before the set time has elapsed.
Function test
Function test:
Ensure that the motion detector is not obscured. Ensure that the coverage area is not restricted by items such as through large furniture. To set the detection range and the daylight test, turn the knobs to the positions shown. The motion detector is activated after a warm-up phase of approx. 30s. If no further movement takes place in the sensing area of the sensor, the sensor switches off.
Technical Data
Technical Data:
Operating voltage:| 220-240V AC 50Hz
Maximum power consumption:|
Electrical protection:| IP65
Protection class:| II
---|---
Detection moving speed:| 0,6-1,5m/s
Ambient temperature:| -20° – +40°C
Humidity:| <93%
Possibilities of adjustments:
Detection area:
|
Max.10m (<24°C)/190°
Sensitivity when switching (with regard to the ambient brightness):|
<3-2.000LUX
Time setting (switching off delay):| Min. 10s +/- 3s – Max. 30min
+/-2min
Information for private households
Information for private households (WEEE)
The Electrical and Electronic Equipment Act (WEEE) contains a large number
of requirements for the handling of electrical and electronic equipment. The
most important ones are summarised here.
-
Separate collection of waste equipment
Old, worn-out or defective electrical and electronic equipment is referred to as waste equipment. These devices must not be disposed of in the normal household waste or together with the residual waste. The devices should be transferred to special collection and return systems. -
Batteries and rechargeable batteries as well as illuminants
As a rule, owners of WEEE shall separate spent batteries and accumulators that are not enclosed in the WEEE, as well as light sources that can be removed from the WEEE without causing damage, from the WEEE before handing it over to a collection point. This does not apply if WEEE is prepared for reuse with the participation of a public waste management authority.
Batteries or rechargeable batteries that contain harmful substances are marked with the symbol of a crossed-out dustbin and must not be disposed of in household waste. Below the dustbin symbol is the chemical name of the pollutant – in the example below “Cd” for cadmium. “Pb” stands for lead, and “Hg” for mercury: If disposed of improperly, the substances contained in the batteries may cause hazards to health and the environment. The hazards are averted by the separate collection and proper disposal of used batteries. -
Options for returning old appliances
Owners of WEEE from private households can hand it in free of charge at the collection points of the public waste management authorities or at the take- back points set up by manufacturers or distributors. -
Data privacy notice
Old devices often contain sensitive personal data. This applies in particular to information and telecommunications technology devices such as computers and smartphones. In your own interest, please note that each end user is responsible for deleting the data on the end-of-life devices to be disposed of. -
Meaning of the “crossed-out dustbin” symbol
The symbol of a crossed-out dustbin regularly displayed on electrical and electronic equipment indicates that the respective device must be collected separately from unsorted municipal waste at the end of its service life.
Cleaning
Danger:
Before start cleaning the product interrupt the current circuit by switching
off the circuit breaker or unscrewing the fuse! Use a slightly moistened cloth
for cleaning. In order not to damage the product, it is essential to avoid
water penetrating into the housing! Never clean the device under running
water! Do not use solvent-containing cleaner for cleaning.
- Address: SEBSON Sebastian Sonntag Walter-Behrendtstr.10 44329 Dortmund Germany.
- Email: support@sebson.de VAT-Nr.: GB179436663 WEEE-Reg.-ID.: 500617
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>