SEBSON Mirror Wal C90 LED Bathroom Mirror Light Instructions
- June 15, 2024
- SEBSON
Table of Contents
SEBSON Mirror Wal C90 LED Bathroom Mirror Light
Product Information
Specifications
- Product Name : MIRROR_WAL_C90 1
- Intended Use : Suitable for mounting on the wall or ceiling
- Protection Class : IP44 (suitable for use in damp rooms)
- Operating Voltage: 220-240V AC 50/60Hz
- Power : 15W
- Luminous Flux: 1,300lm
- Color Temperature : 4,000K
- Protection Class: II
General Safety Information
- The installation of this product should only be done by a qualified person according to the valid regulations for electrical installation.
- Turn off the product immediately without tension and ensure that a restart is no longer possible in case of damages or contact with water.
- Keep this product away from children and animals as it contains small parts that can be swallowed.
- Avoid setting up the light beam directly at people or animals to prevent fire damage or eye damage. Do not look directly into the light source.
- Do not attempt to exchange the built-in luminous in the light.
- Modifying this product is not allowed as it may affect the proper and safe functioning of the device and invalidate the warranty claim.
- Do not connect a dimmer to the product as it may cause damage to the lamp.
- Do not cover the light with heat insulating materials to prevent damage to the LED due to heat development.
- Protect the product from external damage, heavy dirt, moisture, and excessive heat.
- Use only the supplied items to ensure that the warranty claim does not expire.
- Repairs should only be done by an expert using original spare parts.
- Adhere to the accident prevention regulations of the professional trade association for electrical equipment and facilities in commercial institutions.
Installation Instructions (Fig 1)
Before installing, make sure that the circuit is interrupted. Follow the steps
below:
- Choose a suitable location on the wall or ceiling for mounting the mirror luminaire.
- Mark the position for drilling holes using the provided template or by measuring the dimensions of the luminaire.
- Drill the necessary holes using a suitable drill bit according to the marked positions.
- Insert the supplied screws into the drilled holes and tighten them securely.
- Connect the electrical wires of the luminaire to the mains voltage following proper electrical installation practices.
- Ensure that all connections are secure and insulated properly.
- Turn on the power to test the functionality of the mirror luminaire.
Cleaning Instructions
Before cleaning the product, make sure to interrupt the circuit by turning off
the corresponding circuit breaker. Follow the steps below:
- Use a soft, lint-free cloth or sponge dampened with water or a mild household cleaner to gently wipe the surface of the luminaire.
- Avoid using abrasive cleaners, solvents, or harsh chemicals as they may damage the product.
- Dry the luminaire thoroughly with a clean, dry cloth.
- After cleaning, restore the power by turning on the circuit breaker.
Thank you for choosing a product of SEBSON. Read the instructions carefully and keep them looking up before starting this product. A long and failure-free operation can only be guaranteed if the installation and start-up are done properly. Before starting up this product, please check for external damage. In case of visible external damage, we immediately dis-advise the start-up of this product! Please remove all packaging material of this product before the first start-up and check the content for completeness!
Intended use:
This mirror luminaire of the SEBSON brand is suitable for mounting on the wall
or ceiling, for example. Due to its nature, it has a protection class of IP44
and is therefore suitable for use in damp rooms.
Scope of delivery:
- 1 Mirror light
- 2 Screws and 2 Dowels (Ø 6mm) for fixing
General safety information
- Danger : The installation of this product may be done only by a qualified person according to the valid regulations for electrical installation!
- Danger : In case of damages or contact with water turn off this product immediately without tension and make sure that a restart is no longer possible!
- Danger of suffocation: Keep this product away from children and animals! The packaging contains small parts that can be swallowed!
- Caution : Please set up the light beam of the light never directly at people or animals to prevent fire damage or eye damage and avoid looking directly into the light source!
An exchange of the built-in luminous in the light is not possible!
- The remodeling of this product is not allowed! The proper and safe functioning of the device can no longer be guaranteed if it is modified! In addition, this will invalidate the warranty claim!
- Do not connect a dimmer as this may cause damage to the lamp.
- Do not cover the light with heat-insulating materials! As a result of a strong heat development, the LED can be damaged!
- The manufacturer does not accept any responsibility for injuries or damage resulting from improper use of this product!
- Any other use than the description may result in damage to the product. So the dangers are such as electric shock, short circuit, fire etc.
- We reserve the right to make changes to the product, the packaging or the operating instructions as well as printing errors.
- Protect the product from external damage, heavy dirt, moisture, and excessive heat!
- In order that the warranty claim does not expire please use only the supplied items. Repairs may only be done by an expert and only by using original spare parts!
- In commercial institutions, the accident prevention regulations of the professional trade association for electrical equipment and facilities must be adhered to.
Instruction for installation
(Fig 1):
Danger :
- Before installing make sure that the circuit is interrupted! For installation, the work on the mains voltage is required.
- Remove the associated mains fuse or deactivate the switch fuse!
- Check by using a voltage tester if the line is de-energized.
- Make sure that the current circuit will not be closed during the installation!
- There is a danger to life here!
Attention : Before drilling the mounting holes, make sure that there are no gas, electricity or water pipes at the drilling location that could be damaged by this!
- This product is only suited for indoor use and not for outdoor use!
- Plan a minimum distance of 50cm between the illuminated area and the lamp.
- Observe the safety instructions and technical data before installing this product!
- Note on installation:
- L: Live wire (black or brown)
- N: Neutral conductor (blue or grey)
Technical Data
- Operating voltage: 220-240V AC 50/60Hz
- Nominal wattage: 15W
- Nominal luminous flux: 1.300lm
- Rated color temperature: 4.000K
- Electrical protection : IP44
- Protection class: II
This product contains a light source of energy efficiency class F.
Information for private households (WEEE):
The Electrical and Electronic Equipment Act (WEEE) contains a large number
of requirements for the handling of electrical and electronic equipment. The
most important ones are summarised here.
Separate collection of waste equipment
Old, worn-out or defective electrical and electronic equipment is referred to
as waste equipment. These devices must not be disposed of in the normal
household waste or together with the residual waste. The devices should be
transferred to special collection and return systems.
Batteries and rechargeable batteries as well as illuminants
As a rule, owners of WEEE shall separate spent batteries and accumulators that
are not enclosed in the WEEE, as well as light sources that can be removed
from the WEEE without causing damage, from the WEEE before handing it over to
a collection point. This does not apply if WEEE is prepared for reuse with the
participation of a public waste management authority.
Batteries or rechargeable batteries that contain harmful substances are marked with the symbol of a crossed-out dustbin and must not be disposed of in household waste. Below the dustbin symbol is the chemical name of the pollutant – in the example below “Cd” for cadmium. “Pb” stands for lead, “Hg” for mercury:
If disposed of improperly, the substances contained in the batteries may cause hazards to health and the environment. The hazards are averted by the separate collection and proper disposal of used batteries.
Options for returning old appliances
Owners of WEEE from private households can hand it in free of charge at the
collection points of the public waste management authorities or at the take-
back points set up by manufacturers or distributors.
Data privacy notice
Old devices often contain sensitive personal data. This applies in particular
to information and telecommunications technology devices such as computers and
smartphones. In your own interest, please note that each end user is
responsible for deleting the data on the end-of-life devices to be disposed
of.
Meaning of the “crossed-out dustbin” symbol
The symbol of a crossed-out dustbin regularly displayed on electrical and
electronic equipment indicates that the respective device must be collected
separately from unsorted municipal waste at the end of its service life.
Cleaning:
Danger : Before start cleaning the product interrupt the current circuit by switching off the circuit breaker or unscrew the fuse! Use a slightly moistened cloth for cleaning. In order not to damage the product, it is essential to avoid water penetrating into the housing! Never clean the device under running water! Do not use solvent-containing cleaner for cleaning.
SEBSON
Sebastian Sonntag Walter-Behrendt-Str.10 44329 Dortmund Germany
support@sebson.de
VAT-Nr.: GB179436663
WEEE-Reg.-Nr. : DE 78960174
FAQ’s
Can I use this mirror luminaire in a bathroom?
Yes, the mirror luminaire has a protection class of IP44, making it suitable for use in damp rooms such as bathrooms.
Can I replace the built-in luminous in the light?
No, connecting a dimmer to the product may cause damage to the lamp. It is recommended to avoid using a dimmer with this product.
Can I connect a dimmer to this product?
No, connecting a dimmer to the product may cause damage to the lamp. It is recommended to avoid using a dimmer with this product.
Can I modify the product?
No, modifying the product is not allowed as it may affect the proper and safe functioning of the device and invalidate the warranty claim.
How should I clean the mirror luminaire?
Before cleaning, interrupt the circuit by turning off the corresponding circuit breaker. Use a soft, lint-free cloth or sponge dampened with water or a mild household cleaner to gently wipe the surface of the luminaire. Avoid using abrasive cleaners, solvents, or harsh chemicals. Dry the luminaire thoroughly with a clean, dry cloth before restoring the power.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>