KRAMER MegaEdge Portable Table Mount Power Station User Guide

: June 4, 2024
: Kramer

Table of Contents

Step 1: Check what’s in the box
Step 2: Get to know your MegaEdge
Step 3: Install MegaEdge
Step 4: Connect power
Step 5: Operate MegaEdge
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MegaEdge Portable Table Mount Power Station
User Guide

This guide helps you install and use your MegaEdge for the first time.
Go to www.kramerav.com/downloads/MegaEdge to download the latest user manual and check if firmware upgrades are available.

Step 1: Check what’s in the box

✅MegaEdge Secure Portable Power Supply
✅1 Quick start guide
✅1 T20 Torx bit
✅2 T20 Torx security screws

Step 2: Get to know your MegaEdge

#| Feature| MegaEdge-Universal Function 1| MegaEdge-WW Function
---|---|---|---
1| AC Power Connector (x2)| Connect to up to two 120V AC power-consuming devices simultaneously.| Connect to up to two 220/240V AC power-consuming devices simultaneously.
When a single power socket is connected, consumption should not exceed 5A. When both power sockets are connected, the total consumption should not exceed 6A.
2| 5V-2A USB Fast Charging Port (x2)| Use to charge a mobile device.
3| USB-C| Use to charge a mobile device.
4| Control Button| Short press to turn MegaEdge On.
Once on, each additional short press toggles MegaEdge AC power outlets On/Off
MegaEdge consumes some power when the AC power indicator is on even when no devices are connected to it.
Long press to turn MegaEdge Off.
5| Power On Indicator LED| Lights are blue when MegaEdge is on.
6| Numeric LED Display| Indicates percent of power remaining.
7| AC Indicator LED| Lights are red when AC power is enabled.
USB DC power is always on when MegaEdge is on.
8| Mounting Bracket| Used with a security screw for securing the MegaEdge to the table.
9| Security Screw (2)| For securing the MegaEdge to the table.

Step 3: Install MegaEdge

Install MegaEdge

Carefully place MegaEdge over the edge of a table at the desired location so that the table edge is pressed against the device.
Secure MegaEdge to the table using the Torx bit and the two security screws provided.
Tighten each security screw through the MegaEdge mounting bracket into the table.

Step 4: Connect power

MegaEdge requires a 100V – 240V AC, 2.0A extension cord with a C7 connector, and an appropriate plug type based on the user’s country.
To fully charge MegaEdge, connect the power cord to the main’s electricity for at least 8 hours.
Safety Instructions (See www.kramerav.com for updated safety information)
Caution:

There are no operator serviceable parts inside the unit.
Warning:
Use only the power cord that is supplied with the unit.
Disconnect the power and unplug the unit from the wall before installing it.
Do not open the unit. High voltages can cause electrical shock! Servicing by qualified personnel only.
To ensure continuous risk protection, replace fuses only according to the rating specified on the product label is located on the bottom of the unit.

Step 5: Operate MegaEdge

To Turn MegaEdge On

Press the Control button.
Power On LED lights blue.
To Turn MegaEdge Off
Press the Control button for 3 seconds.
Power On LED is no longer lit.
To Toggle AC Power On/Off
Press the Control button to toggle between AC power On and AC power Off AC LED is lit red when AC is on.

MegaEdge consumes some power when the AC power indicator is on even when no devices are connected to the AC.
When no power is being used, MegaEdge powers off automatically after 1 minute.

To Charge MegaEdge
When not in use, plug it into an AC outlet for at least 8 hours to fully charge the MegaEdge.

WWW.KRAMERAV.COM