ZUNMOS HJ-3895 PU Leather Office Flip up Armrest Chair Instruction Manual

ZUNMOS HJ-3895 PU Leather Office Flip up Armrest Chair

Package List

• Without further ado, we kindly suggest you to list all parts needed for the chair first.

Assembly Instruction

1. Step 1:
   Turn the Base (7) upside down, then insert Legs (6) one by one to Base.
   Use the Wrench (13) to screw Ten Bolts (11) into the pre-drilled screw holes to fix Base and Legs.
   

2. Step 2:
   Insert the Casters (8) into the holes at the end of each Leg.
   Insert the Gas Lift (5) to the center hole of the Base
   

3. Step 3 :
   Align the Mechanism (4) over the pre-drilled holes underneath the Seat (2), make sure the front of the mechanism is facing the front of the Seat.
   Attach the Mechanism to the Seat using Four Bolts (9), tighten all the bolts with the Wrench (13).
   

4. Step 4 :
   Turn the Seat (2) upright and align the center hole of the Seat Plate over the lift, then push the Seat down onto the lift firmly until the connection is secure.
   Attach the Armrest (3) to the Seat (2) with Two Bolts (10), using the Wrench (13) to tighten.
   The Bolt only needs to be screwed in 50%. The installation of the other side Armrest is the same.
   
   Note 1: The same marks on both seat and armrests are tips for installing the armrests in the correct direction.
   Note 2: Armrests are labeled with the letter “L” (left) or “R” (right).

5. Step 5:
   Set the Back (1) stand up.
   Attach the Back (1) to the Arms by inserting one Bolt (10) in the holes with the Wrench (13). The Bolt only needs to be screwed in 50%.
   

6. Step 6:
   Rotate the back of the chair up, then secure it with the Bolt (10) use the Wrench (13). Adjust the balance on each side of the chair, and 100% tighten all the bolts at this step.
   

7. Step 7:
   Press Caps (12) into screw holes of each side.

CAUTION:
Make sure all bolts and screws are fully tightened before using chair.
Lubricate all moving parts and tighten all bolts/screws every 6 month or whenever needed.

Instructions For Use

1. Seat Height: Paddle-shaped lever on the right side
   
   To raise:
   While taking your weight off chair, lift lever up.
   To lower:
   While seated, lift lever up.

• At the proper height, your feet should rest flat on the floor. 2. Tilt Tension: Long stem under the seat with knob
  
  To increase tension:
  While seated, turn knob forward (Counter clockwise).
  To decrease tension:
  While seated, turn knob backward (Clockwise ).

• Set the tilt tension to control the resistance you feel when leaning back. 3. Operating the tilt lockout
  
  To let your chair tilt back, pull the control handle out.
  To stop your chair from tilting, sit forward, then push the control handle in.

  4. Armrests adjustment
     
     The armrest can be adjusted.
     Make it up and down if you need.

Safety And Maintenance

• Do not stand on the chair, Do Not use the chair as a stepladder.
• Use this product for seating one person at a time.
• Do not use the chair unless all bolts and screws are firmly secured.
• Avoid contact with sharp objects to prevent puncturing the fabric.
• Every 6 months, check all bolts and screws to ensure they are tight.
• To clean, spot clean only using a damp towel and mild cleaner, first test on a small, unseen area of fabric.
• Chair weight limit not to exceed 250 lbs.

Safety Information

Sit in the center of the chair, with your back to the backrest

Do not sit at the front edge of the chair

Do not stand on the chair

Do not use the chair with more than one person

Do not push the chair around when a person is sitting in it

Do not push down on the backrest when a person is reclined

Do not place all your weight on only the backrest

Limited Warranty

The producer promises to repair or replace any chair that is found to be defective in material or workmanship within one(1) and year from the date of original purchase so long as you, the original purchaser, still owns it. This is your sole and exclusive remedy. This warranty is subject to the provisions below.

EXCLUSIONS:

This warranty does not apply and no other warranty applies to:
Normal wear and tear, which are to be expected over the course of ownership.
Misuse, abuse, or excessive use of the product.
Modifications or attachments to the product that are not approved by the manufacturer.
Products that were not installed, used or maintained in accordance with product instructions and warnings.
Products used for rental or commercial purposes.
Damage caused by the carrier in-transit is handled under separate terms.

SEATING USAGE:
Normal use for seating is identified as the equivalent of a single shift, forty- (40) hour workweek. To the extent that a seating product is used in a manner exceeding this, the applicable warranty period will be reduced in a pro-rata manner.
Some retailers might have custom models imported directly from the factory and therefore are not supported by our local service team because we don’t have the correct parts, please contact your retailer directly for support. If you have any questions about that we will be happy to assist and identify those items.

RETURN POLICY:
We adopt a 30 days return policy which means that all products purchased on this website may be returned to us within the timeframe. You need to contact us within 30 days after the product(s) came into your possession and the product(s) must be returned to us without any undue delays.
Returned products must be returned in the same condition as they were sent and they must be sent in its original packaging.
If the product is not faulty, (i.e. if you changed your mind or if you are unhappy with the product for some other reason), the cost of shipping will all on you. And it is your responsibility that the package arrives safely to us so we recommend that you use a courier service where it is possible to track the shipment.
If the product is faulty when you receive it please contact us and we will help you out (see more information under Manufacturer Warranty).
We reserve the right to give a partial refund in cases when the product(s) is not in an unused condition, is damaged or has missing parts not due to our error.

HOW RETURNS WORK:
Contact us through the contact form on our website and attach the invoice to the message as proof of purchase. And please also write the reason for return.
We will then get back to you as soon as possible with information on where to send the product(s).
As soon as we have received the product(s) and made an inspection we will inform you of our decision.
If a refund is approved we will automatically credit the purchase to your credit card or original method of payment.
If the product(s) is damaged, not in its original condition or missing parts we will inform you if you are eligible for a partial refund. This is decided from case to case depending on the severity of the damages or what parts are missing.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>