TUPAVCO TSW425 2.5G Switch User Manual

TUPAVCO TSW425 2.5G Switch User Manual

Product introduction

5-port/8-port 2.5Gbps switch, with line speed forwarding capability per port. With 5-port/8-port 10M/100M/1g/ 2.5Gbps RJ45/Poe port, this series of switches It has good network adaptability for applications such as security monitoring, diskless startup and wireless networking.

Product characteristics

• Each port supports MDI/mdix auto flip and duplex / rate self negotiation.
• Support IEEE 802.3x full duplex flow control and backpressure half duplex flow control.
• Support IEEE 802.3af/at/poe++/BT (PoE switch only)
• Energy saving technology is adopted to automatically adjust the signal strength by detecting the length of network cable and workload, so as to effectively reduce energy consumption
• The equipment meets the national CCC standard, fully meets the requirements of safety regulations, and is safe and reliable.
• Plug and play, no management required.
• Dynamic LED indicator provides simple working status prompt and troubleshooting.

Product display

Schematic diagram of front panel

1. 5*10M/100M/1G/2.5Gbps RJ45 Port

2. 5*10M/100M/1G/2.5Gbps PoE Port

3. 8*10M/100M/1G/2.5Gbps RJ45 Port

4. 8*10M/100M/1G/2.5Gbps PoE Port
   1 port support 10M/100M/1G/2SGbps high-power at/t/PE/

Indicator definition

PWR: When on, the switch is connected to the power supply
PoE: When on, PoE starts to supply power

LED indicator:

the indicator light is green: the transmission rate is 10 / 100M

Schematic diagram of rear panel

1. S Port 2.5G Desktop style

2. 8Port 2.5G Desktop style

Product supporting list

• One switch

• One power adapter

• A user manual and warranty card

Installation guide

Power socket specification
The power line of the switch adopts single-phase two-wire power socket. The left foot is zero line and the right foot is live line. Please check before operation.

Connect the power cord

1. Check that the selected power supply is consistent with the power supply requirements marked on the switch,
2. For the external type, connect the power adapter, connect AC100-240V, 50-60Hz and DC input 52V, as shown in **Figure 1.1.2.

**

Post installation inspection

Please check the following items after installation:

1. Check whether there is enough heat dissipation space around the switch and whether the air circulation is smooth:
2. Check whether the power supply of the power socket meets the specification of the switch
3. Check that the power supply, switch, rack and other equipment are properly grounded:

Post installation inspection

Please check the following items after installation:

1. Check whether there is enough heat dissipation space around the switch and whether the air circulation is smooth;
2. Check whether the power supply of the power socket meets the specification of the switch:
3. Check that the power supply, switch, rack and other equipment are properly grounded:

Matters needing attention

To avoid equipment damage and personal injury caused by improper use, please follow the following precautions.

• During installation, keep the power off, wear anti-static wrist, and ensure that the anti-static wrist is in good contact with the skin to avoid potential safety hazards:
• The switch can work normally only under the correct power supply. Please confirm that the power supply voltage is consistent with the voltage marked by the switch
• Before the switch is powered on, please confirm that it will not cause overload of the power circuit, so as not to affect the normal operation of the switch or even cause unnecessary damage;
• In order to avoid the danger of electric shock, do not open the shell when the switch is working, and do not open it by yourself even when it is not charged;
• Before cleaning the switch, pull out the power plug of the switch. Do not wipe it with wet fabric or clean it with liquid;
• Avoid placing other heavy objects on the surface of the switch to avoid accidents

Product application

**SPOE 2.5G Application example:

* The bottom of the switch is equipped with a wall jack (Jack size: 5mm5mm

**8PoE 2.5G Application example

* The bottom of the switch is equipped with a wall jack (Jack size: 5mm5mm)

Technical parameter

| | | |
---|---|---|---|---
Fi xed Port| S’ 10S111.0014/1Gbps(2.5Gbps 8145 port| 4’1011/100MilGtos/2.5Gbps PoE port•L’Uplink| 8’10M/10014/1Gbps/2.5GbpsR.M5 port| 11’1011/10011/1Gbps/2.5Gbps PoE poet
PoE ports| | 1 port supports IEEESO2atiatipoestIBT(11AX_90W) 2.5 port supportsIEES02.3atjat(MAX_30W)| | 1 port supports IF FEE02atiatipootrIBT(MAX_SOW: 2•i) port supports 11E802.3atiat(MAX_30W)
Pot out Pin| | Port1:1/20)r3/61-1: 4/51•).WDD) Por12-5:113(+43/61-1| | P0111:11201.3(60: 4/50).7/111-1 Port3-8:1/2(+).316(-)
Network protocol| IEEE 802.3/U. IEEE 802.3aD, IEEE 802.361. IEEE 802.3x
Port Specification| 1011(100M/1000M/2.SGAuto
CPU| MIPS•341(c Up to SOOMH:CPU
Packet Buffet| 12mbit SRAM
Jumbo frame| Up la 121(B
Bandwidth| 80Gbps
Packet Forwarding| 28.191Ipps
MAC Address| 16K
Transmission Distance| 10BASE-T i Cat3,4,5 VTP(4250 meter)100BASE•TX i CatS or later UTP(150 meter) 2$00/1000BASE-TX i Cate rioter UTP(150 meter)
LED Indicator| PWItWhdin on, thet wite h is connected to the power supply Winn the NM notwollt Ron LOW wont, the Wammission rate is 2-540pt%TenthekW network port lightsgreen, the transmission rate is 14bpsWhen the green network port light on the hen is ca. Ow transmission Me os 10 /100.1| PWR‘Vawn en. the “Itch I“°“e”ed lot” power Pot: When on. PoE Mole to wooly powerWhen the Jolt network port lien wane. the transmission rite b 1.SGbpsWhen the left network port lights gre.n,the transmission rate is IGI4Yawl the greennetwork port light on the right e’en. (Retransmission M0,10/1001| PWR:      n en, the write h Ilia…netted wah• power supplyWhen the lel Resort port lien orange, the irwamistion rate is 2.5GbpsWhen the left network port Reds grwen,the Inonemission rate is IGbpsWhen thenennetwork port tight on the right is on, their onsmission MR1,10/10011| awa:when on.the switch istonnetted to We power supplyPOEII”facon. Pot Wens to supply motsWhen moan network „on uomsomnoo. the transmission taken 23444When Melo,. network port lights gleta. the transmission mg 4 IGbp,Wiwi, the remnetwork penlight on the right is on, the transmission rate Is10110:41
Opea weivng TempowwW itasy| -10,-.55T: 5%,-90% RH Non coagulation
StwageToRwwww/sewiedy| .40,.75•C; 5%–95% RH Non coagulation
Power| AdaptorTUAX1SW(AC100-2401/ 50/60HZUAX0.3A)| I AdaptoDMAX 65W(AC100-240V50/60HZ MAX0.9A)| Adaptor;MAX 15W(AC100-240V 50(60HZ MAX0.3A)| I Adaptor.MAX120W(AC100-240V 50/60HZ MAX 1.5A
Product tin/Pack:again(ew–e| 160mmill2mm•31mm
193mms131mm•91mm| 223mm113mms28mm
30Smm205mm’S5mm
N.W(G.W(kg)| 0.8kg(1.2kg| 1.1kgrit.Sks
Installation| Desktop optional wall machine hanger parts]
Lightning protection level| 31(VB/20uSi 1P30
Certificate| CE mark, commercial; CE/LVD E N60950 i FCC Part ISCIass EU ROCS;
Warranty| Whole device for 1 year(Accessories not included)

Product parameters and appearance are subject to updale or change without notice. Please refer to the official website by yourself.

Product packing list:

Open the product packing box and take out the objects carefully. Please check the packing list carefully to ensure that all items are included and undamaged. If there is any shortage or damage of accessories, please contact us in time.

1. atwitch
2. power adapter
3. user manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>