VOLLRATH 15022 InstaCut Wall Mount Fruit & Vegetable Wedger w/ Cut Options Instruction Manual
- June 1, 2024
- VOLLRATH
Table of Contents
VOLLRATH 15022 InstaCut Wall Mount Fruit & Vegetable Wedger w/ Cut
Options
Product Information
Specifications:
- Product Name: Vollrath Food Slicer
- Model: Tabletop and Wall Mount Models
- Blade Type: Sharp cutting blade assembly
- Material: Stainless steel
- Dimensions: Varies based on model
Product Usage Instructions
Blade Handling and Maintenance:
Blades are sharp and can cause cuts. Ensure only trained personnel handle the
equipment. Wash new blades with warm, soapy water to remove the protective oil
film. Handle blades with caution, keeping the sharp edge away from you.
Changing the Blade Assembly:
- Remove the pusher head assembly based on the model type.
- Raise the bumpers approximately 2 inches.
- Loosen the thumbscrew and carefully remove the blade assembly.
- Install the new cutting blade assembly by aligning the tab on the blade holder into the base groove and tightening the thumbscrew.
Assembly and Lubrication:
Slide bumpers down guide rods, position pusher head assembly onto the guide
rods, and check alignment. Lubricate the guide bar with mineral oil after each
use to maintain smooth operation.
FAQ:
-
Q: Can I use cooking oil to lubricate the guide bar?
A: No, do not use cooking oil as it may become sticky and damage the equipment. Use mineral oil or Petrol-Gel for lubrication. -
Q: How often should I replace the cutting blade assembly?
A: Replace the cutting blade assembly when it becomes dull or damaged. Regularly inspect the blade for wear and tear.
Installation Instructions
WARNING
Sharp Blade Hazard
- Blades are sharp and can cause cuts and amputation.
- To avoid injury from sharp blades, handle with caution. Only trained personnel should operate equipment or perform maintenance.
Wash new blades with warm, soapy water and rinse thoroughly to remove the thin protective oil film. Keep the sharp edge away from you when handling blades.
- Remove the pusher head assembly:
- Tabletop models: Slide the pusher head off the rod guides.
- Wall mount models: Remove the locking pin (J). Lift the handle and slide the pusher head off the guide rods. Place the pin back into the hole on the handle assembly to prevent loss.
- A. Guide Rods. Guides and aligns the pusher head onto the blade set.
- B. Handle. Used to lower and raise the pusher head block
- C. Guides. Used for smooth and consistent operation of pusher head on the guide rods
- D. Pusher Head Assembly. Made up of the pusher head block (and “T” handle for tabletop models).
- E. Bumpers. Cushions on the top of the pusher head.
- Raise the bumpers approximately 2” (5.0 cm).
- Loosen the thumbscrew and carefully remove the blade assembly. Remove the cutting blade assembly by pressing upwards on the bottom of the side of the blade holder, where the thumbscrew is located. Discard the old blade assembly.
- Install the new cutting blade assembly by inserting the tab on the blade holder into the groove in the base, then lowering the blade holder into the seated and flush position in the base. Tighten the thumbscrew.
- Slide bumpers down guide rods to contact base assembly. Position the pusher head assembly onto the guide rods, slowly lower the pusher head assembly, and check the pusher head block to blade alignment.
- Lubricate the guide bar with mineral oil or petrol gel after each use. Do not use cooking oil as it will become sticky and may permanently damage the equipment.
- F. Thumbscrew. Used to secure the pusher head block or the blade assembly.
- G. Pusher Head Bock. Pushes the food product through the blade set. Specifically sized to match the corresponding blade assembly.
- H. Blade Assembly. Houses the blades. Specifically sized to match the corresponding pusher head block
- I. Base Assembly. Holds the guide rods and blade assembly.
- J. Locking Pin. Secures the pusher head to the handle.
Contact Information
- The Vollrath Company, L.L.C. 1236 North 18th Street Sheboygan, WI 53081-3201 U.S.A.
- Main Tel: 800.624.2051 or 920.457.4851
- Main Fax: 800.752.5620 or 920.459.6573
- Customer Service: 800.628.0830
- Canada Customer Service: 800.695.8560
Technical Services
- techservicereps@vollrathco.com
- Induction Products: 800.825.6036
- Countertop Warming Products: 800.354.1970
- All Other Products: 800.628.0832
www.vollrath.com. © 2016 The Vollrath Company L.L.C.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>