SUNGOOYUE X6 Folding Drone Instruction Manual

AGE 14+
FOLDING DRONE WITH OBSTACLE AVOIDANCE
FUNCTION OPERATING MANUAL

Instruction Manual
*Please read this manual carefully before operation and keep it properly for future reference.

KNOW YOUR REMOTE CONTROL

KNOW YOUR DRONE

The drone uses the 24G frequency band, which can be operated by multiple people at the same time without interfering with each other, Through the remote control, the drone can be controlled to achieve functions such as flight, rollover, fine-tuning, one-key take-off, one-key landing, speed headless mode, calibration, height setting, obstacle avoidance and other functions.

ACCESSORIES

Notes:
Please check the number of accessories carefully (as shown above).Please provide proof of purchase and contact the store for replacement if any missing parts.

OPTIONAL ACCESSORIES LIST

Notes:
If any of the above accessories are damaged during operation, you can contact the seller to purchase.

PRE-FLIGHT PREPARATION

1. FLIGHT ENVIRONMENT
   Indoor: Spacious spaces away from barriers, crowds or pets are preferred.
   Outdoor: Sunny, windless and breezy weathers are preferred.
   Please keep the drone in sight during the flight and keep it away from barriers, high-tension cables, trees and people.
   Do not fly in extreme environment, such as hotness, coldness, strong wind or heavy rain.

2. OPEN THE WINGS
   OPENING STEPS
   (1) Open the front arm(close to camera)
   (2) Open the back arm
   Fold the back armf firstly and then the ront arm when folding.
   

3. ASSEMBLING PROTECTIVE GUARD
   Align the protective frame with the arm and install it (Figure 1), press it until it is in place, and then press the position (Figure

2. up to fasten the protective frame.

4. ASSEMBLING PROPELLERS
   Align the blades with the motor shaft and install them (the arm identification must be consistent with the blade identification), Tighten the screw clockwise .

5. BATTERY CHARGING FOR DRONE
   A. Remove the lithium battery from the bottom of the drone.
   B. Connect USB charging cable with the charging interface of the lithium battery.

Notes:
The LED light is on when charging, and the LED light is off when charging is complete, and the charging time ‘ is about 150 minutes

LITHIUM BATTERY INSTRUCTION

1. Open the remote control battery cover
   

2. Remote control battery installation
   Open the battery cover and insert the 3 AAA batteries correctly according to the electrode instructions.(Batteries not included)

Notes:

1. Make sure the battery are loaded correctly according to the polarity indications on the battery compartment.
2. Please do not mix old and new batteries together.
3. Please do not mix different types of batteries together.

SIGNAL CONNECTION OF TRANSMITTER AND RECEIVER

After turning on the power switch of the fuselage, place the drone on a horizontal plane, and then turn on the remote control switch, the frequency will be automatically paired, two beeps will be heard, the remote controller indicator light and the drone LED light will be on, then the frequency pairing is completed.

TRANSMITTER CALIBRATION

Apply transmitter calibration when the drone fails to take off vertically. Press the “One button calibration*button when the lights of drone are on and then start flashing and keep on again, the calibration is complete. the drone must be placed on horizontal surface in a steady state when the calibrations conducted

START YOUR FLIGHT

1. One—key Ascend and One-key Landing
   Press the “One—key Ascend” button, the drone blades rotate and automatically fly to a height of 1.5 meters. Press the button again to land the drone with one button 

2. Right joystick
   Flips & Rolls
   After the drone flies to a height of more than 3 meters, click the roll button and move the right joystick (rudder) to the left or right to realize the roll action in this direction.
   Right joystick
   Hover
   When you release the left joystick (throttle) after the ascent/descent action, the drone will hover at a certain height.
   High/low speed and Light control
   Lightly press the button to control the speed of the drone, a “di” sound is a slow speed, and then tap the button again, a “di” and a “di” sound twice as a fast speed, and then the cycle repeats. The default speed of the drone is low speed.
   Obstacle Avoidance Mode
   Press the button to turn on the obstacle avoidance mode, and press the button again to turn off the obstacle avoidance mode. Three-sided obstacle avoidance, according to the direction of the remote control, it will slop when encountering an obstacle.
   It is recommended to turn on the obstacle avoidance function in an indoor flight environment with a length and width of 6 x 6 meters or more. When the UAV turns on the obstacle avoidance mode, the speed will slow down and the fast gear cannot be turned on. Therefore, it is recommended to fly indoors when the obstacle avoidance mode is turned on. Basic Flight
   Use the left joystick to control the flight altitude and turn left/right, and the right joystick to control the forward, backward, left and right sidde flight directions.
   Left joystick

Headless Mode and One key to return home
The flight direction of drone is subjected to the direction of remote control.

1. When drone adjust the frequency, the drone is default as common mode. Then the indication light of drone is normally on. Short press the headless function key of remote  control, the remote control beeps once and enters headless state. When you press the headless function key again, you listen to a long beep sound and the drone exits the  headless mode.
2. In the headless state, operator doesn’t need to identify the direction of nose, but control the drone according to the operating lever of remote control.
   emergency stop
   In case of emergency, tap the button to brake the drone and hover in place.

FINE—TUNING FUNCTION

When the aircraft spins in the air or tilts in different directions, you can use fine-tuning to correct the action.
Press the fine-tuning button and hear a beep, then move the joystick in the opposite direction to adjust and calibrate until the aircraft does not deviate.
If there is no operation for 5—6 seconds after entering the fine-tuning, the fine-tuning function will automatically exit.

Notes:
When the drone is within 30cm from the ground, it will be affected by the blade vortex made by itself and become unstable. This is “ground effect”. The lower the drone is, the greater the effect will be.

FAQ

quadcopter battery in right way.
Too strong wind force.| Do not fly in windy days. The performance and the control of the quadcopter will beaffeded by the strong winds.
Fail to ascend| The rotation speed of main blades is too slow.| Push up the throttle joystick.
The battery of the quadrocopter is not fully charged.| Please full charge the quodcopter.
Landing too soom| The throttle stick is pulled down too fast.| Pull down the throttle stick slowly to perform a smooth landing.
Out of control| Beyond the effective
controlling distance.| Ensure operation within the controllable distance: remote control of 100 meters

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>