YiRiSO RFCD-V310 Hair and Beard Trimmer User Manual

Table of Contents

Please read these instructions carefully before use. And keep present instructions for future reference.
Check that your mains voltage corresponds to that stated on the appliance.
Never immerse the appliance in water or any other liquid for any reason whatsoever and always place it in a dry environment.
Incorrect operation and improper use can damage the appliance and cause injury to the user.
The appliance must be used only for its intended purpose. No responsibility can be taken for any damage caused by incorrect use or improper handling.
Never use accessories, which the producer doesn’t recommend. They could constitute a danger to the user and risk damaging the appliance.
Caution! Don’t allow small children to play with the foil: There is a danger of suffocation!
This device isn’t a toy, don’t leave small children or people with disabilities to play with.
In order to ensure your children’s safety, please keep all packaging (plastic bags, boxes, polystyrene, etc. out of their reach.
Children shall not make cleaning and use maintenance without supervision.
Regarding the instructions for cleaning, thanks to refer to the below paragraph of the manual.

Notices

Twhilel product body may be a little hot when using or charging. But it does not affect its performance.
Make sure the adaptors are labeled with output DC 5V 1A before charging.
Please remove the charger in time to avoid overcharging and shorten the battery life.
Don’t use petrol, alcohol, or thin to clean the product. Otherwise, the product color may be changed ged n.
Use diluted soap and water to clean the product.
Don’t charge the product if the room temperature is higher than 40°or lower than 0•.

Cutting Size Adjustment

If using charging base, please connect the USB cable with the base and then plug into the socket. (the blue charging indicator will be working on the base.
Make sure the machine is in the position of Power Off and then put it into the base to start the charging. The display will show a fixed red plug icon and the power percentage. As soon as it is fully charged, the figure in the display should be fixed 100.
You also can directly connect the machine with the USB cable for charging.
Charging time is around 2.5 hours.
The red plug icon in the display will be flashing if the left power is less than 15%.

The plug-and-play function means that you can use the machine while charging in case of insufficient power.
Put the adaptor connector terminal into the port of the machine and then plug it into a socket. Switch on the machine and then use it.
After using it, switch off and then disconnect the USB cable connector from the machine.
If the battery has been used out, it may be difficult to start the machine even if it is plugged in. You should restart it after charging at least one or two minutes. while charging, the machine may be a little hot, however, it is a normal phenomenon.
Take the USB cable out of the power socket.
Take the plug out of the product.
Please hold the plug and take it out.
Don’t pull the cord in order to avoid any damage.
Don’t charge the product for more than 6 hours each time.

Note: If the machine has not been used for a long time, please ensure the batter is charged at least once time within 3 months to avoid damage.

The Cutting Head Disassembling & Assembling:

Cutting head disassembling
Use another hand to hold the cutting head to prevent it flying out.
Cutting head assembling
- First turn the size selection control knob into the position of 2.0mm(furthest left).
- Insert B into A.
- Press it until a click sound.

Cutting Head Cleaning

From the date of purchase, you can get a one-year warranty if our confirms that the problems or the defects are caused by the production process or material. (Except for the changes of blade.)

Free warranty service can’t be provided under the following conditions:

The damage was caused by the repair or reconstruction of the place which isn’t appointed by our company.
The damage was caused by incorrect use, dropping, or accidents.
The damage was caused by a natural disaster or abnormal voltage.
The damage was caused by industrial use, commercial use, or some other uses that are out of normal use ranges.

After-sales email: support@iyiriso.com

Scan the QR code or visit support.iyiriso.com to activate the warranty: