PHILIPS SQM9222-27 Full Motion TV Monitor Wall Mount Bracket Instruction Manual

PHILIPS SQM9222-27 Full Motion TV Monitor Wall Mount Bracket

SPECIFICATIONS

• Display Size: 17in. to 55in.
• Maximum Load: 55lbs (25kg)
• Mounting Pattern: 200mm x 200mm (7.9in. x 7.9in.) max
• Profile: lin. (2.6cm)

BOX CONTENTS

• Wall Plate (xl)
• Mount Arm (x2)
• Instruction Manual (xl)
• Hardware Kit (xl)

WARNINGS

• Read these instructions before you begin. If you are unsure of any part of the process, contact a professional contractor or installer for assistance.
• Improper installation can result in injury or damage.
• The wall or mounting surface must be capable of supporting the combined weight of the mount and the display; if not, the structure must be reinforced.
• Before drilling, locate pipes, wires or any other hazards in the wall where you wish to install the mount.
• Safety gear and proper tools must be used. Failure to do so can result in injury or damage.
• Two people are recommended for installation. Do not attempt to lift a heavy display without assistance.
• Follow all instructions and recommendations regarding adequate ventilation and suitable locations for mounting your display. For more information, consult the owner’s manual for your particular display.

CAUTION : This wall mount is intended for use only with the maximum weight of 55lbs (25 kg). Use with heavier than the maximum weight indicated may result in instability, causing possible injury.

TOOLS REQUIRED

• Phillips-Head Screwdriver
• Electric or Portable Drill
• 1/Sin. (3mm) Drill Bit and Stud Finder for Drywall Installation
• 5/16in. (5mm) Masonry Bit for Concrete Installation

HARDWARE KIT

INSTALLATION

Part 1A – Mounting to the Wall (Drywall)

IMPORTANT! For safety reasons, this mount must be secured to a wood stud capable of supporting the combined weight of the mount and display. Do not mount to drywall alone.

1. Use a high quality stud finder to locate a stud where you wish to install your mount. Mark both edges of the stud to help identify the exact center.
   NOTE : You must use the center of each stud to avoid cracking or splitting the wood during installation.

2. Place the wall plate against the wall with the arrow pointing up. Make sure it is level.

3. While another person holds the wall plate in position, mark two locations (top and bottom) for securing the mount to the wall.

4. Set the wall plate aside and drill a 1/Sin. (3mm) pilot hole at each marked location.

5. Place the wall plate back against the wall and attach it using the lag bolts (A) and lag bolt washers (B) provided. Do not overtighten these bolts and do not release the wall plate until both bolts are in place. Ensure that the wall plate remains level after all bolts are secured.

Part 1B – Mounting to the Wall (Concrete)

IMPORTANT! For safety reasons, the concrete wall must be capable of supporting the combined weight of the mount and the display. The manufacturer takes no responsibility for failure caused by walls of insufficient strength.

1. Place the wall plate against the wall in the desired location with the arrow pointing up. Make sure it is level.
2. While another person holds the wall plate in place, mark three locations on the wall for securing the mount Mark two locations at the top of the wall plate and one location at the bottom of the wall plate.
3. Set the wall plate aside and drill an 5/16in. (Smm) hole at each marked location. Remove any excess dust from the holes.
4. Insert a concrete anchor (C) into each hole so it is flush with the concrete surface . A hammer can be used to lightly tap the anchors into place, if necessary. Note: If the concrete wall is covered by a layer of plaster or drywall, the concrete anchor must pass completely through the layer to rest flush with the concrete surface.
5. Place the wall plate back against the wall and attach it using the lag bolts (A) and lag bolt washers (B) provided (see Fig. 5). Do not overtighten these bolts and do not release the wall plate until both bolts are in place. Ensure that the wall plate remains level after all bolts are secured.

Part 2 – Attaching the Mount Arms to the Display

IMPORTANT! Use extra care during this part of the installation. If possible, avoid placing your display facedown, as it may damage the viewing surface.
NOTE: This mount comes with a selection of different screw diameters and lengths to accommodate a wide variety of display models. Not all of the hardware in the kit will be used. If you cannot find the appropriate screw size in the kit provided, consult the manufacturer of your display for more information.

1. Determine the correct length of screw to use by examining the back of your display.
2. If the back of your display is flat and the mounting  holes are flush with the surface, you will use the shorter screws (D, G or J) from the hardware kit.
3. If the back of your display is curved, has a protrusion or if the mounting holes are recessed, you will need to use the longer screws (E, F, H, K, Lor M) and may also need to use the spacers (0).
4. Determine the correct diameter of screw to use by carefully trying one of each size (M4, M6 and MS) from the hardware kit. Do not force any of the screws. If you feel resistance, stop immediately and try a smaller diameter screw.
5. Attach the mount arms to the back of your display using the screws identified in steps 7 and 2.
   • If you are using the M4 and M6 screws, you will need to use the M6 washers (I). If you are using the MS screws you will need to use the MS washers (N).
   • If you are using the longer screws on a display with a curved or recessed back, you may also need to use the spacers (0). Use one spacer or two spacers stacked as needed. Only use a spacer if necessary.

Part 3 – Final Assembly

1. With the help of another person, carefully lift your display and place it on the wall plate.
   Do not release the display until the mount arms have securely hooked onto the wall plate.

2. To prevent the display from being lifted from the wall plate, tighten the safety screw located on each mount arm using the Phillips-head screwdrive. IMPORTANT! The safety screws must be tightened at all times to prevent the display from being accidentally knocked from the mount.

3. Periodically clean your mount with a dry cloth. Inspect all screws and hardware at regular intervals to ensure that no connections have become loose over time. Retighten as needed.

Read instructions or watch easy-to-follow video. Scan QR code or visit https://bit.ly/2W3jCoX

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>