Yeecn L33L42 Motion Sensor Closet Light User Manual
- June 14, 2024
- Yeecn
Table of Contents
Yeecn L33L42 Motion Sensor Closet Light
Reglette LED Rechargeable USB
Product List
Use Instructions
Button use instruction(independent battery must be installed)
Three types: ON/M1/M2. Touch button for 1 seconds to control on/off.
After power on, press switch mode.
ON: In steady on mode.
M1: Motion sensing + ambient light sensing. In this mode, when ambient brightness is lower than default value, the light will automatically turn on when human movement is sensed; when human movement is undetected during lighting period, the light will automatically turn off after 20 seconds;
M2: Human body sensing.The light will turn on automatically once human
activity which will be not influenced by environment. During lighting period,
the light will automatically turn off after 20 seconds without human activity.
When the indicator senses human movement, the indicator light of the current
mode automatically lights up and goes off automatically when no human movement
is sensed.
Touch-type brightness/color temperature adjustment button:
Long press to switch the color temperature3000K/4500K/6500K cycle, short press
to adjust the brightness by 25%, 50%, 75%and100%.
The initial brightness is 100%,and the color temperature brightness of the
next lighting is according to last shutdown by default.
Installation Mode
Metal mounting plate installation position Main body of light is mounted on the metal position by magnetic, or on other magnetic conductive materials.
-
Please fully charge independent battery before use, as green light of charging indicator is always on.
-
The light body is connected with battery through metal contacts. Before installation, please ensure that metal contacts are intact without dirt
-
Battery supplies power to light body through metal contact pin. Before installation, please make sure no foreign matter blocking.
-
Align battery power supply end with light body contact point, then insert protruding part of light body into the battery terminal pin position, battery pin come into contact with light body.
-
Stick metal mounting plate on metal position of light body, then tear off foam tape to install it on the plane and press it for 1 minute to fix it.
Installation completed.
Basic Parameter
Lamp Body
- Color Temperature: 3000K/4500K/6000K
- Temperature: -10-+40℃
- Material: Aluminium/ABS
- Humidity: 0%-85%RH
Independent Battery
- Battery Capacity: 2000mAH
- Input: 5V=1A
- Size: 3.94″1.57″0.39″
- Material: Aluminium/ABS
- Output Voltage: About 5V
- Independent Battery Weight: 66g
- Charge Time: About 3Н
Diagram For Sensing Range
Sensor as center to expand 120 degree fan-shaped region with 5 – 7 metres ahead and 2 – 3metres in the side. Sensor effect is related to the installation position, ambient environment, human size and move-speed.
Safety Precautions
- Please ganrantee the voltage before use. Any improper voltage may cause damages to the product and cause safety hazard.
- Please install and use the product far away from heat sources, such as heating vents and conditioner vents,and places not exposed to sunlight.
- Sensor is not allowed to covered by other objects. Please clean the lamp with a soft cotton cloth and without any corrosive solvents.
- This device is for indoor use only. Do not spray water on it or soak it in water to avoid any safety hazard.
- Do not use this product as a toy for child play.
- Do not disassemble the product. the light-emitting diode may cause damage to your eyes.
- This device will generate heat during operation. Please keep proper ventilation.
Precautions for Use
- Please confirm whether the voltage is in line with the operating voltage of the product before use Voltage may damage the product and bring safety hazards.
- If the motion sonsor light does not turn on during the first use,please charge it first.
- Products in the installation should be far away from heat sources such as range hood, heating outlet, direct sunlight.
- The product surface sensing area can not be covered by other items, cleaning the product surface, as required Wipe with a soft cotton cloth, do not use corrosive solvents to clean.
- This product has not been waterproof test, do not drench or soak water, so as to avoid safety risks.
- Please do not use this product as children’s toys to avoid accidents.
- The LED module cannot be replaced. Please do not disassemble the product without permission.
PLEASE READ THE INSTALLATION INSTRUCTION CAREFULLY BEFORE USING THE PRODUCT MADE IN CHINA
FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any inte rference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interferenceto radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.