MED LINKET AM801 Blood Oxygen Saturation Monitor Finger Adults User Guide
- June 14, 2024
- Med-Linket
Table of Contents
MED LINKET AM801 Blood Oxygen Saturation Monitor Finger Adult
Product Information
Specifications
- Product Name: PULSE OXIMETER
- Troubleshooting Guide: Included
- Display: LCD screen
- Transmitting Tube: LED lights
- Battery: Required (not included)
- Measurement: Pulse amplitude, temperature
Product Usage Instructions
Troubleshooting
This section explains how to troubleshoot the PULSE OXIMETER. Tables list possible PULSE OXIMETER difficulties, along with probable causes, and recommended actions to correct the difficulties. Please refer to Table 2 for detailed instructions.
Table 2 – Instruction for Menu Setting
| Phenomena | Possible Causes | Solutions |
|---|---|---|
| The power button was not pressed in place | Re-press the power button in place, | |
| and keep 1-2 seconds | ||
| Not Install battery | Install battery | |
| Abnormal starting-up of Pulse-Oximeter | Battery use-out | Replace battery |
(display screen and transmitting tube of LCD presenting lights
off| Install battery improperly| Check and re-install battery
Partial damage of Metal dome (which is Contact authorized
distributors directly connected to the battery)| | Contact authorized
distributors
Damage in Connection between mainboard and battery holder (i.e.
Damage in flexible printed circuit board (FPCB) or break in welding
spot)| | Contact authorized distributors
No display on screen, but the transmitting tube of LED lights
on.| Damage in display screen or break in the connection spot of
display screen| Contact authorized distributors
No reading display on Pulse-Oximeter| Poor perfusion problem| Adjust the
finger position; Use your middle or index finger in
preference; Warm your fingers;
The transmitting tube of LED lights off| | Contact authorized distributors
Fail auto-off Inaccurate Temp Measurement| External Temp-probe is still
working; Damage in collection tube
or other device parts; The surface Temp-Probe did not firmly stick
on the skin surface.| Pull out the external temp-probe; Stick the Temp-Probe
on the
proper measuring position by medical proof fabric; Place the
Temp-Probe in proper position according to the specification; Keep
the correct measuring method by 10 mins, and then get the
result.
FAQ
Q: How do I install the battery?
A: To install the battery, make sure the power button is pressed in place, and keep it pressed for 1-2 seconds. Then, properly insert the battery into the designated slot.
Q: What should I do if there is no display on the screen?
A: If there is no display on the screen but the transmitting tube of LED lights on, it may be due to damage in the display screen or a break in the connection spot. In such cases, please contact authorized distributors for assistance.
Q: How can I get an accurate temperature measurement?
A: To ensure accurate temperature measurement, make sure the external Temp- Probe is not working, stick the Temp-Probe firmly on the skin surface using medical proof fabric, place the Temp-Probe in the proper position according to the specification, and keep the correct measuring method for at least 10 minutes before obtaining the result.
Troubleshooting Guide
This section explains how to troubleshoot the PULSE OXIMETER. Tables list possi-ble PULSE OXIMETER difficulties, along with probable causes, and recommended actions to correct the difficulties. Detailed see table 2 as below.
Table 2：Instruction for Menu setting
| Phenomena | Possible Causes | Solutions |
|---|
Abnormal starting-up of Pulse-Oximeter (display screen and transmitting tube of LCD presenting lights
off ）
| The power button was not pressed in place| Re-press the power button in
place, and keep 1-2 seconds
Not Install battery| Install battery
Battery use-out| Replace battery
Install battery improperly Partial damage of Metal dome (which is directly
connected to the battery).| Check and re-install battery Contact authorized
distributors
Damage in Connection between mainboard and battery holder (i.e. Damage in
flexible printed circuit board (FPCB) or break in welding spot).| ****
Contact authorized distributors
No display on screen, but the transmitting tube of LED lights on.| With damage in display screen or break in the connection spot of display screen|
Contact authorized distributors
No reading display on Pulse-Oximeter
| Poor perfusion problem (general- ly, there’s no display on pulse amplitude
indicator but the light of LED transmitting tube is on and the finger is
inserted in place)| If there’s no pulse amplitude displayed on the screen,
Please,Adjust the finger position;Use your middle or index finger in preference;
Warm your fingers;
The transmitting tube of LED lights off| Contact authorized distributors
Fail auto-off
| External Temp-probe is still working| Pull out the external temp-probe
---|---|---
Damage in collection tube or other device parts.| Contact authorized
distributors
Inaccurate Temp Measurement
| The surface Temp-Probe did not firmly stick on the skin surface.| Stick the Temp-Probe on the proper measuring position by medical proof fabric
Wrong position of Temp-Probe
| Place the Temp-Probe in proper position according to the specification
No enough measuring time
| Keep the correct measuring method by 10 mins, and then get the result.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>