hansgrohe 9301859 Two Handle Pressure Balancing Valve Trim User Manual

hansgrohe 9301859 Two-Handle Pressure Balancing Valve Trim

Technical Information

• Water pressure
• recommended 15 – 75 PSI (0.1-0.5 MPa)
• maximum 145 PSI (1 MPa)
• Hot water temp.
• recommended 120°-140° F (49°- 60°C)*
• maximum 176°F (80° C)*
• Flow rate 44 PSI 4.5 GPM (17.0 l/min)

Please know and follow all applicable local plumbing codes when setting the temperature on the water heater.

Installation Considerations

• For best results, Hansgrohe recommends that this unit be installed by a licensed, professional plumber.
• Please read over these instructions thoroughly before beginning installation. Make sure that you have all the tools and supplies needed to complete the installation.
• This trim is for use with iBox Universal Plus model 01850181 (not included).
• To prevent scald injury, the maximum output temperature of the shower valve must be no higher than 120°F. In Massachusetts, the maximum output temperature can be no higher than 112°F.
• Adjust the rotational limit stop (see page 22) during installation. Further adjustments may be necessary due to seasonal water temperature changes.
• Do not install a shut-off device on either outlet of this valve. The use of such a device can defeat the ability of the valve to balance the hot and cold water pressures.
• The pressure balance trim with the diverter is suitable for a two-function installation, such as a showerhead and tub spout, or showerhead and handshower.
• Do not use this trim in a one-function installation.
• Do not use a diverter tub spout.
• This mixing valve is for use with shower heads rated at 1.1 GPM (4.2 L/min) or higher.
• Keep this booklet and the receipt (or other proof of date and place of purchase) for this product in a safe place. The receipt is required should it be necessary to request warranty parts.

The rotational limit stop (see page 22) To reduce the risk of scald injury, adjust the rotational limit stop if:  The maximum output temperature is greater than 120°F (49°C) or that permitted by local plumbing code.

• The temperature of the incoming hot or cold water supply changes seasonally, or if changes are made to the water heater.

Service Stops

Important
The 01850181 iBox Universal Plus rough valve (not included) incorporates service (isolation) stops on the hot and cold inlets. Use a 4 mm Allen wrench to open and close the stops.

Tools Required

Installation Suggestions

• Do not use a diverter tub spout.

Flush the hot and cold supplies

• Remove the dust cover.
• Open both stops.
• Allow the hot and cold supplies to flush for at least 5 minutes.
• Close the stops.

Installation

1. To reduce the risk of scald injury and property damage, make sure the stops are closed. Cut the plaster shield so that it extends ¹⁄₁₆” – ⅛” (1-2 mm) from the finished wall surface.
2. Seal the wall around the plaster shield with waterproof sealant. Failure to seal the wall may result in property damage. Remove the flush insert screw, the flush insert, and the seals.
3. Dry the inside of the valve
4. Measure the distance from the front of the plaster
5. Add ½” to this measurement. Cut each screw so that it is X + ½” long.
6. Open the stops
7. Install the carrier plate so that the notch is at the bottom.
8. Test the valve: Temporarily install the handles. Turn the pressure balance handle counter-clockwise as far as it will go.
9. Make sure that cold water flows from the valve first, and becomes warmer as the handle is turned.
10. Use caution with skin contact to hot water to reduce the risk of scald injury. If the valve opens through hot, reverse the cartridge. See page 19.
11. Measure the temperature of the output water. If the maximum high temperature is greater than 120°F or that permitted by local plumbing code, adjust the rotational limit stop. See page 22.
12. Turn the water off.
13. Place a small amount of caulk at the top and side grout lines where the escutcheon will rest.
14. Lubricate the pressure balance cartridge o-ring using a small amount of white plumber’s grease. Install the sleeves. Install the escutcheon.
15. Lubricate the diverter stem with a small amount of white plumber’s grease. 15862xx1, 15864xx1: Install the handle adapter. Tighten the screw.
16. 15865xx1 only: Install the handle adapter and the snap connector. Tighten the screw.
17. Install the diverter handle.

Reverse the cartridge

1. Use caution with skin contact with hot water to reduce the risk of scald injury. If the valve opens through hot, reverse the cartridge. Close the stops.
2. Unscrew the nut.
3. Do not attempt to pry the cartridge from the function block by using a screwdriver as doing so can damage the cartridge. Damage to the cartridge can result in property damage.
4. Place the adapter and the handle on the cartridge stem. Turn the handle counter-clockwise approximately ¼ turn after hitting the stop.
5. Lift the cartridge out. Turn the cartridge 180°, so that the “hot side” marking is on the right. Install the cartridge Install the nut.
6. Open the stops. Continue the installation

Adjust the Rotational Limit Stop

1. Pull the white rotational limit stop outward.
2. Rotate clockwise to decrease the maximum temperature. Rotate counterclockwise to increase the maximum temperature.
3. The temperature change per notch may be anywhere from 4° – 16° F, depending on local inlet conditions. Repeat as necessary.
4. When finished, make sure that the rotational limit stop is fully retracted. Continue the installation.

Replacement Parts

• XX = Colors
• 00 = Chrome
• 14 = Brushed Bronze
• 34 = Brushed Black Chrome
• 67 = Matte Black
• 70 = Matte White
• 82 = Brushed Nickel
• 83 = Polished Nickel
• 92 = Rubbed Bronze

User Instructions

It is normal for the showerhead and/or the tub spout to drip for several minutes after the valve is turned off. Water left in the showerhead/tub spout is draining away. It does not mean that the shower valve is leaking. To reduce the risk of property damage or product failure, do not use excess force on the handle to stop the dripping. The use of the excess force will break the cartridge.

Maintenance

Should the volume of water decrease over time, first inspect and clean the showerhead(s). If the problem persists, inspect the cartridge. At least once per year, inspect the cartridge, including the check valves on the rear of the cartridge. Replace the cartridge if dirty or worn, or if leaking when in the off position. Use caution with skin contact to hot water to reduce the risk of scald injury. Before servicing the valve, turn the water off using the stops on the iBox Universal Plus or at the main shutoff.

Troubleshooting

Cleaning Recommendation for Hansgrohe Products Modern bathroom faucets, kitchen faucets, and shower products are made from different materials to comply with the needs of the market with regard to design and functionality. To avoid damage to the product, it is necessary to take proper care of it.

For best results

• Prevent the buildup of mineral scale and /or soap residue by cleaning your Hansgrohe product(s) when needed.
• Select a cleaning agent specifically intended for the type of product.
• Do not use these types of cleaners as they will cause damage to your Hansgrohe product:
• Any cleaning agent containing hydrochloric acid, formic acid, lye, or acetic acid.
• Abrasive cleaning powders, pads, or brushes.
• Steam cleaners.
• “No rinse” cleaning agents.
• Always follow the instructions provided by the manufacturer of the cleaning agent.
• Do not mix cleaning agents, unless directed by the manufacturer.
• Do not spray cleaners directly onto the product as drops could enter openings and gaps and cause damage.
• When using spray cleaners, spray the cleaner onto a soft cloth or sponge.
• Always rinse your Hansgrohe product thoroughly with clear water and polish dry with a soft cloth after cleaning.

Important

• Residue from soaps and shampoos can cause damage. Rinse the product with clean water after each use.
• Residue from basin/tub/tile cleaner can cause damage to faucets and fittings. Immediately rinse any overspray from the Hansgrohe product.
• Do not store any cleaning agents under your Hansgrohe product, such as in a vanity unit, as the fumes may damage the product.
• Damage to the product caused by improper care or the use of improper cleaning agents is not covered by the warranty.
• If a component of the product is damaged, replace it to reduce the risk of personal injury, property damage or product failure.

Hansgrohe, Inc. Limited Warranty

Offering our customers the highest quality at all times is a fundamental part of the Hansgrohe, Inc. company philosophy. We offer consumers a limited warranty on our hansgrohe® and AXOR® branded products. This warranty is limited to products manufactured by Hansgrohe, Inc. that are purchased from a Hansgrohe, Inc. authorized seller by a consumer in the United States or Canada after September 1, 2019, and installed in either the United States or in Canada.

WARRANTY

Hansgrohe, Inc. warrants to the original consumer purchaser that Hansgrohe and AXOR products will be free from defects in material and workmanship for as long as the original consumer purchaser owns both the product and the home in which the product was originally installed. For commercial purchasers, the warranty period is (a) one (1) year for Hansgrohe products and (b) five (5) years for AXOR products, in each case from the date of purchase. The warranty period for products in the Rubbed Bronze, Matte Black and Matte White finishes are three (3) years from the date of purchase. This warranty is non- transferable.

WHAT WE WILL DO
Hansgrohe, Inc., at its option, will replace any product or part of the product that proves defective in workmanship and/ or material, under normal installation, use, service, and maintenance. If Hansgrohe, Inc. is unable to provide a replacement part or product and repair is not practical or cannot be made in a timely fashion, Hansgrohe, Inc. may elect to refund the purchase price in exchange for the return of the defective product. REPAIR OR REPLACEMENT (OR, IN LIMITED CIRCUMSTANCES, REFUND OF THE PURCHASE PRICE) AS PROVIDED UNDER THIS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER. WHAT IS NOT COVERED BY THE WARRANTY?

Because Hansgrohe, Inc. is unable to control the quality of Hansgrohe or AXOR products sold by unauthorized sellers, unless otherwise prohibited by law, this warranty does not cover Hansgrohe or AXOR products purchased from unauthorized sellers. Authorized sellers can be found on Hansgrohe and AXOR branded websites. Labor and other expenses for disconnection, de-installation, or return of the product for warranty service (including but not limited to proper packaging and shipping costs), or for installation or reinstallation of the product are not covered by this warranty. Hansgrohe, Inc. shall not be liable for any damage to the product resulting from

• reasonable wear and tear

• outdoor use

• misuse (including the use of the product for an unintended application)

• freezing water

• excessive water pressure

• pipe corrosion in the home in which the product is installed abuse, neglect or improper or incorrectly performed installation, maintenance or repair, including the use of abrasive or caustic cleaning agents or “no-rinse” cleaning
  products.

• This warranty does not cover: (i) accessories, connected materials and products, or related products not manufactured by

• Hansgrohe, Inc. (ii) any Hansgrohe or AXOR product sold for display purposes or (iii) Hansgrohe or AXOR products purchased from unauthorized sellers.

WHAT YOU MUST DO TO OBTAIN WARRANTY SERVICE OR INFORMATION
Contact your retailer, or contact Technical Service at Hansgrohe, Inc.
1492 Bluegrass Lakes Parkway
Alpharetta, GA 30004
Toll-free 800 -334- 0455
In requesting warranty service, you will need to provide:

1. The sales receipt or other evidence of the date and place of purchase.
2. A description of the problem.
3. Delivery of the product or the defective part, postage prepaid and carefully packed and insured, to Hansgrohe, Inc.
4. 1492 Bluegrass Lakes Parkway Alpharetta, GA 30004 Toll-free 800 -334- 0455
5. When warranty service is completed, any repaired or replacement product or part will be returned to you postage prepaid.

REVISED SEPTEMBER 1, 2019.
Limitation on Duration of Implied Warranties: Some States do not allow limitations on how long an implied warranty lasts, so the below limitations may not apply to you. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED TO THE STATUTORY PERIOD OR THE DURATION OF THIS WARRANTY, WHICHEVER IS SHORTER.

Limitation of Special, Incidental, or Consequential Damages: Some States do not allow the exclusion or limitation of incidental or consequential damages, so the below limitations and exclusions may not apply to you. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY DOES NOT COVER, AND HANSGROHE, INC. SHALL NOT BE LIABLE FOR, ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING LABOR CHARGES TO REPAIR, REPLACE, INSTALL OR REMOVE THIS PRODUCT), WHETHER ARISING OUT OF BREACH OF ANY EXPRESS OR IMPLIED WARRANTY, BREACH OF CONTRACT, TORT, OR OTHERWISE. HANSGROHE, INC. SHALL NOT BE LIABLE FOR ANY DAMAGE TO THE PRODUCT RESULTING FROM REASONABLE WEAR AND

TEAR, OUTDOOR USE, MISUSE (INCLUDING USE OF THE PRODUCT FOR AN UNINTENDED APPLICATION), FREEZING WATER, EXCESSIVE WATER PRESSURE, PIPE CORROSION IN THE HOME IN WHICH THE PRODUCT IS INSTALLED, ABUSE, NEGLECT OR IMPROPER OR INCORRECTLY PERFORMED INSTALLATION, MAINTENANCE OR REPAIR, INCLUDING THE USE OF ABRASIVE OR CAUSTIC CLEANING AGENTS OR “NO-RINSE” CLEANING PRODUCTS.

Notice to residents of the State of New Jersey: The provisions of this warranty, including its limitations, are intended to apply to the fullest extent permitted by the laws of the State of New Jersey. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

PRODUCT INSTRUCTIONS AND QUESTIONS
Upon purchase or prior to installation, please carefully inspect your product for any damage or visible defect. Prior to installing, always carefully study the enclosed instructions on the proper installation and the care and maintenance of this product. If you have questions at any time about the use, installation, or performance of your product, or the Limited Warranty, please write us or call us toll-free at 800 -334- 0455.
Hansgrohe, Inc. 1490 Bluegrass Lakes Parkway Alpharetta, GA 30004 Tel. 800-334-0455 Fax 770-889-1783 www.hansgrohe- usa.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>