CMTOOL Articulating Borescope Inspection Camera User Manual

June 14, 2024
CMTOOL

CMTOOL Articulating Borescope Inspection Camera

WARNING

Before using the articulating borescope, please pay attention to the following operations:

  • Please do not use this camera to connect to other manufacturers’ hosts without authorization, even if their interfaces are the same;
  • Do not use this product in some areas where live cables or charged objects may be contacted. Exposed metal parts can conduct electricity, which may cause danger;
  • Do not let children operate the product;
  • This product is prohibited from being used for medical treatment or human body testing;
  • Please keep the product clean, avoid exposure to the sun, or direct contact with water, oil and corrosive liquids;
  • The product is not waterproof;
  • It is forbidden to twist or pull the bending body at the front end of the hose;
  • Please handle with care. Do not bend the hose excessively. The bending limit of the hose is one circle.

PRODUCT INTRODUCTION

Articulating Borescope is specially used to detect narrow and bending spaces that are difficult to enter, such as auto evaporator, combustion chamber, three-way catalytic, etc.
The product has a steering detection function, and has a unique high- temperature alarm function, which makes it convenient for users to penetrate the small probe into the narrow space, and then transfer the vivid, clear and omnidirectional video and pictures to the 5 inch display to meet your various detection needs.

OPERATING ENVIRONMENT & TECHNICAL INDICATORS

Camera Diameter 6.35mm
Pixel 200W
Depth of Field 20-100mm
Viewing Angle 70°
Manual Dimming Three-level dimming
Input Power DC 5V
Service time 3hr
Battery Capacity 3000mAh
Camera Light Source 6 kinds of LED lights
Waterproof Level IP67
Hose Material Flexible metal hose
Hose Length 1m
High Temperature Protection Intelligent protection
Steering Direction Two-way
Steering Angle Max.210°
Bending Radius 35mm
Operating Environment -10~80°C
Humidity 15-90%

PRODUCT STRUCTURE

A Display B SD Interface
C M D Up
E Steering Wheel F Megapixel HD Camera
G Flexible Hose H Settings
I Charging Port J OK
K Down / Toggle L Power On / Light Control
M Photo / Video

OPERATION GUIDE

Power on / off:

  • Long press the power key (H) for two seconds, and the blue indicator light on the display indicates that the power on is successful. Long press the power key (H) again for two seconds to power off.

Light Control:

  • After powering on, press the light control key (H) to adjust the light, and the brightness is adjusted to 3 levels. The machine defaults to the brightest light when it is powered on.

Photo / Video:

  • After powering on, press the photo/video key (I) to take pictures, and long press for 2 seconds to record. Image playback: After powering on, press the M key to start the image playback function, use the up and down keys to find the desired picture or video, and short press the OK key to playback the video.

Time / Date:

  • After powering on, press the setting key twice to switch to the setting interface, scroll down to select the date/time, and adjust to the required time with the up and down keys (confirm the required time with the OK key).

Date tag:

  • The date tag is turned on by default. After turning it on, the date and time will be automatically displayed in the lower right corner of the photos and videos you take.

Recording and sound:

  • Product has a built-in sound recorder and speaker, which will automatically record the sound when you record video, and will have audio when you play back the recorded video.

Charging:

  • Please use 5V adapter or mobile power to connect Type-C/USB cable for charging. The charging voltage and current are 5V/1A. If the voltage is too high, the product may be burnt out. Please note that this product does not support fast charging.

FAULT REPORT

Fault Phenomenon Cause Analysis Troubleshooting
Power fail Battery Loss Charge the borescope
Automatic shut-down Low battery or automatic shutdown is set Charge the

borescope and turn off the automatic shutdown setting
SD Error| SD is not installed well| Reinstall the SD
Charge fail| The charging port is dirty or the charging cable is damaged| Replace the charging cable
Image Blur| The lens is dirty| Wipe the lens clean with a cleaning cloth
SD Recording Fail| Insufficient SD capacity| Replace SD or clean-up files

WARRANTY

  • Thank you for choosing our products, we will provide you with the following services and promises.
  • The warranty period of this product is 1 year.
  • After the warranty period expires, repairs will be charged for replacement parts.
  • After the failure, please contact the manufacturer, we will give you the most complete service in the shortest time.

The following items are not covered by the warranty:

  • Man-made faults are not covered by the warranty

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals