STELLAR LIGHTING LEI 4361 DMX Optic Star Ceiling Kit User Manual

June 14, 2024
STELLAR LIGHTING

STELLAR LIGHTING LEI 4361 DMX Optic Star Ceiling Kit

Accessories

  • Fiber Connector …………………………1 PC
  • Wireless Remote Controller……………1 PC (Optional)
  • User Manual ………………………… . . . . . . 1 PC
  • Signal Cable ………………………………1 PC (for DMX machine only)

Welcome to use Minar professional LED light engine, LEI-4361DMX. Please read the manual carefully before turning on the power. If you have any questions concerning the operation or maintenance, please contact your wholesaler.

Safety Instruction

  1. Make sure the Light Engine and Power Source have the same voltage;
  2. Keep out of the rain or moist areas to avoid shock hazards;
  3. Avoid to use at high ambient temperature ( >40℃);

Technical Data

  • Voltage: 110V~230V AC
  • Life of LED: 50000H
  • Power: 160W
  • Color: RGBW
  • Light Source: 1-4X36W LED
  • Size: 291 × 264× 135mm
  • Gross Weight: 7.0Kg
  • Standard aperture: 28mm/24mm/20mm (Optional:Ф 30mm Max)

Installation dimension of the light engine(see Fig.1)

Light Engine Setup

There are three control modes of LEI-4361DMX, the DMX512 protocol light engine:

  • DMX512 Signal Control Mode: DMX512 Signal is received from a DMX512 console.
  • Master/Slave Mode: One Light Engine is set as Master, while the rest light engines are set as Slave.
  • The master sends a control signal to the slave so that all the machines run the program synchronously.
  • Audio Control Mode: Light engines are controlled by sound.

DMX Channels: 8 Channels
CH1:Red CH2:Green CH3:Blue CH4:White CH5:Speed (16 Tiers)
CH6:Dimmer(8 Tiers) CH7: Strobe (8 Tiers) CH8: Twinkle(8 Tiers)

  1. DMX 512 signal control mode: When a DMX512 console is used, all the light engines, LEI-4361DMX, in the group should be set up as slave machines with a DMX address of “001”.
  2. DMX address setup: Holding button “UP” and press “DOWN” continuously until the display shows three digits between 001 505 in editing mode, press the button “UP” or “DOWN” to select the address.
  3. Master/Slave mode: The settings of the Master/Slave light engine:
  4. The connection of Master/Slave Control Mode(See Fig. 3):
  5. Signal cable and connector (See Fig.4):
  6. The signal cable should be a 2×0.5mm audio cable

Wireless remote controller (See Fig.5)

  • Press the two buttons “UP” / “DOWN” beside the Display at the same time. When it displays, press either button “UP” / “DOWN” to show
  • (status of remo tecontrol). The remote function is on. 15-Key Remote Controller
  • Program Selection: Press “PRO”, then press the digit key on the controller, “” “ ”, to choose the desirable program, or you can use it to select.
  • Dimming: Press the key “DIM”, then press “ ” “ ” to have the desirable brightness, or you can use it to adjust.
  • Speed of the color wheel: Press the key “SP”, then press “ ”-” ” to adjust the speed, or you can use it to adjust

Notice
Address codes of slaves (machines) are not adjustable under remote control status. When you are selecting the program, only double-digit numbers on the controller are recognizable (e.g. 00, 01, 02…).

Attached Table

Chapter 2 Installation of Fiber Optic
Connecting the fiber optic with the Light Engine

Solid Core fiber optic(see Fig. 1)

  1. Cut the fiber to the specified length. The cross-section should be vertical to the fiber and kept clean and smooth.
  2. Peel off 50-100mm of the PVC jacket of the fiber optic cable (not necessary if there is no PVC jacket). Be careful not to hurt the fiber optic.
  3. Unscrew the PG Connector and insert the fiber optic cable into the PG Connector and Fiber Connector until the end of the cable is flush with the Fiber Connector. Screw tightly the PG Connector.
  4. Insert the finished Fiber Connector into the Fixing Flange, screw tightly the Screw

Installation of the end part of the Multi-String fiber optic
Drill holes on the installing board according to the design. Then insert the fiber optic string into holes and fix it with epoxy glue. Trim the end of the fiber string to be flush with the board or at a required length. Fasten the other end of the fiber string to a harness and insert the harness into the PG Connector and Fiber Connector. Apply the hot knife to cut the fiber end flush with the Fiber Connector. (see Fig.2). Insert the finished Fiber Connector into the Fixing Flange and screw tightly the Screw.

Commonly used installation method of fiber optic cable

  1. Side Liahtina Fiber Opticísee Fia.3).
  2. End Liahtina Fiber Optic:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals