X5UIBI Car Jump Starter with Air Compressor User Manual

JUMP STARTER WITH AIR COMPRESSOR

User Manual

X5UIBI Car Jump Starter with Air Compressor

Warnings:
Product Safety Instructions, Operation Specifications, and Precautions;

1. If the product s stored for more than 3 months, it requires charging.
2. When starting the vehicle, the clamp must be used, and do not start the vehicle continuously in a short time.
3. Itis not allowed to charge this product immediately after starting the vehicle.
4. 1t is not allowed to be heated or used close to the fire source, and it s not allowed to be put into water or disassembled or reconstructed without permission.
5. The battery clamp and battery clamp wire shall not be damaged or corroded Before starting, ensure that the blue plug of the battery clamp is fully inserted into the product starting port, and ensure that the battery clamp is correctly connected to the  positive and negative poles, so as to avoid melting of the blue plug and weakening of the product starting performance due to poor contact; for more than 3 continuous starts, a 2-minute interval is required to prevent the battery clamp from being hot and  separating from the product; and please remove the product from the vehicle battery within 30 s after starting to avoid damage.
6. In case of battery leakage, it shall not be reused and shall be recycled with appropriate equipment; in case of contact with skin, wash immediately with soap and clear water; and in case of contact with eyes, rinse eyes with cold running water for at least 10  minutes and seek medical attention immediately.

Warranty Includes
12 Months Online After-Sales Service
Within 12 months, we will provide timely and effective online after- sales service after your purchase.
If any problem persists, stop using the jump starter and contact our service team directly at sales@uibi.com.cn, we will do our best to solve the problem within 24 hours.

Instructions of Components and Functions

1. Instructions of component buttons
   : Power On-off Button
   OK Button: Air Pump Start Button
   SETButton: Air Pump Setting Button
   +: Air Pressure Increase Button or Up Switch Button
   – : Air Pressure Decrease Button or Down Switch Button

Function instructions

Functions of 12V jump start, USB fast charge output, USB 5V/3A input, tire pressure detection and pump and lighting.

Instructions of Button and Display

1. Touch the Button to display_power (“1” in the Figure), air pressure unit (“2”), pump type (“3”) and actual pressure value (“4”); (5 After flashing three times, it enters the pump mode, and short press the power On-off Button to shut down.

2. Turn on the power, press and hold the On-off Button for 2 seconds, and turn on the LED light.
   The white light is constantly on to enter the lighting mode. After short press the button, the LED light enters the SOS mode, short press it again to enter the flashing mode, and then short press the power button to turn off the LED light. Press and hold the  power button at any stage to turn off the LED light.

3. The product will enter the dormant state automatically 30 s after the load is removed;

4. Air pump mode setting
   4.1 In standby and normal working conditions, short press the Setting Button “SET” to enter the setting mode: pump type (“3” in the Figure), preset air pressure value (“4”) and air pressure unit (“2”). The specific setting method is to short press the Setting  Button “SET” to switch back and forth among the above three settings. The current setting should be the flashing content of the icon;
   4.2 lf entering the pump type, short press the “+’/”-” Button to switch back and forth among ba- sketball, bicycle, e-bike and car, and the icon flashes; if the preset air pressure value is entered, short press “+’/”-” Button to adjust the air pressure value, which  flashes; and if the air pressure unit is entered, short press “+’/”-” Button to switch among PSI, BAR, KPA, KG/CM2, and the characters flash;
   4.3 After setting the pump mode, short press the OK Button or exit the setting mode automatically after 5s.
   4.4 Press and hold the OK Button for 2 s to enter the pump mode and start pump; press any button to turn off pump; and the pump interface set last time will be displayed on the next startup.

5. When selecting the pump mode (“3” in the Figure: basketball, bicycle, e-bike, and car), the preset air pressure values of the system will be displayed, which are:
   Basketball: 7 PSI
   Bicycle: 10 PSI
   E-bike: 29 PSI
   Car: 36 PSI
   Attention: Please adjust the air pressure standard in combination with the actual model when pump.

6. Instructions of charging display: The battery icon “1” is displayed from left to right at flashing intervals based on power.

7. Instructions of battery status: When the power of a product is lower than 5 %, the last grid power indicator flashes, pump cannot be performed, and enters the dormant state without load for 30 s.

Operational Instructions

1. Instructions for charging the product engine (TYPE-C)
   Connect the USB cable to the home charger, and insert the USB~C head into the engine with 5V/3A fast charge. Please charge at 0 ~ 50 °C.
   

2. Intructions for 12V jump start
   2.1 Insert the blue connector of the battery clamp into the engine, and the equipment enters the standby mode, in which the contents displayed on the battery clamp is ‘voitage value + Standby;
   2.2 Connect the battery clamp correctly to the positive and negative poles of the vehicle: battery, with red clamp to the battery positive (+) and the black clamp to the negative (-); and at this point, the equipment enters the start mode, and contents displayed  on the battery clamp are voltage value + Standby” or “voltage value + Ready;
   2.3 Do not use the battery clamp when the following alarm occurs, and handle it according to its display error;

Smart clamp

Type| Lamp and buzzer indication| Countermeasure
Standby State Indication| The red/green light of the cable clamp flashes alternately in standby mode.|
Operating Status Indication| The green light is always on when the wire clamp is conducting and working.|
Input Low Voltage Protection| When the protection is triggered, the red light is always on and the buzzer sounds for a long time.| Use after powering up the main engine
Short Circuit Protection| When the protection is triggered, the red light is always on and the buzzer sounds for a long time.| The protection can be automatically released after troubleshooting.
Reverse Polarity Protection| When the protection is triggered, the red light is always on and the buzzer sounds for a long time.| Remove the clamp, and after the fault is eliminated, connect the positive pole of the car battery with the red clamp, and connect the negative pole of the car battery with the black clamp.
Mount wait timeout protection| The red/green lights flash alternately.| Disconnect the clip from the battery to eliminate the fault
High Temperature Protection| When the protection is triggered, the red light is always on and the buzzer sounds for a long time.| Remove the clamp and cool it for a period of time before using it

2.4 Turnthe vehidle ignition switch tothe START position;
25 After the jump start, remove the battery clamp.
3. Instructions for charging electronic products such as phones/tablet PC
3.1 Choose an appropriate charging connector to connect the interface to the phone patch cord;
32 Connect the USB plug of the phone patch cord to the USB output port of the engine;
33 Connect the charging connector to electronic products such as phones/tablet PC;
3.4 Touch the power On-off Button to charge the electronic products such as phones/tablet PC.

3. Instructions of LED lights switching between different modes
   Press and hold the On-off Button for 2 5 to start the LED lighting; then short press the On-off
   Button, and the cycle is as follows: strong light, SOS, and sharp-flash; Press again to turn off the LED light

4. Instructions of tre pressure detection
   5.1 After startup, connect the pump pipe tothe engine;
   5.2 Connect the ather end of the pump pipe tothe tire and pressthe Locking Button;
   53 At thistime, the value inthe display window s the current actual tire pressure.

5. Operational Instructions for tire jump.
   6.1 Connect the pump pipe to the engine after startup;
   62 Select the pump type and set the pressure and ai pressure urit (refer to Poirt 4 of the Button and Display Instructions for specific setting mode);
   63 Connect the pump pipe to the tire, pressthe Locking Button, place the engine on the ground stably, and press and hold the OK Button for 2 s to start pump;
   
   6.4 When the air pressure reaches the set value, the engine will automatically stop pump;
   65 Open the Locking Button and remove the pump pipe.
   Remarks (1) In’the process of cortinuous se for a long time, the forced protection of the engine will be caused by high temperature. At this time, the engine stops output and the display flashes continuously. Please place it at room temperature for a period of  time.
   The protection will be automatically released after the temperature drops, and the display can be used only after it s in normal state (discontinuous flashing).
   (2) Wheninflating other products,select corresponding plug, insall t on the pump pipe, lock the button, and follow the above operation

List of Accessories

Technical Specifications

TechncaSpectications

Starting voltage:| 12 v
UsBoutpuuaes oouput| 5v/3A,9v/2A,and12 V/1.5A
Charge mode/Type-c Input| 5V/3A
Start Current| 1250 A
Peak Current| 2000 A
Gas Engines/Diesel Engines| 8.0/6.0
Product capacity| 16,000mAh(59.2Wh)
Pump pressure(bar)| 10bar/150PSI
Pump time(min)(195/65r15tire)| ≤5min
Product dimension(mm)| 21412553.7(mm)
Temperature range(°C)| -4°F -140°F

Some FAQs

1.Q: How to tum off portable power?

A:The product is featured by smart detection function. As long as there is no load or the charging is over, the engine will enter auto sleep to save power.

2.Q: Howlong does it take to charge the engine?

A It takes about 6 hours to fully charge with USB-5V/3A charger

3.Q: How many times can the engine inflate?

A 8times i the air pressure of vehicle tire (195/65R15) ranges from 0PSI to 36 PSI

4.Q: How many times can the engine start the vehicle? What displacement of the vehicle can be started?

A It can start the vehicle more than 50 times continuously. It can start gasoline vehicles up to 80 L/DIESEL vehiclesupto 60L,

5.Q:What isthe life of the engine?

A It can be used for 3~ 5 years under normal conditions.

6.Q: How long can the engine start the vehicle when the engine i fully charged without use?

A ftcan be stored for 1~ 1.5 years without use. It s recommended to charge every three months.

7.Q: What phenomena may appear inthe pump of the new engine?

A: (1) If the new machine is inflated for a long time, the temperature wil be too high, causing the ailn the trachea to volatilize. It is normal that there may be slight smoke after the gas s inflated. (2) When the product is used for a long time, it will enter the protection state due to high temperature. At ths time, the engine stops output, and the display flashes continuously. The protection will be automatically released after being placed at room temperature for a period of time.

Made in China

Documents / Resources

| UIBI X5UIBI Car Jump Starter with Air Compressor [pdf] User Manual
X5UIBI Car Jump Starter with Air Compressor, X5UIBI, Car Jump Starter with Air Compressor, Starter with Air Compressor, Air Compressor
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>