Thermex 10 Wall Mounted Hoods Instruction Manual

: June 14, 2024
: thermex

Table of Contents

BEFORE MOUNTING/COMMISSIONING
MOUNTING
INSTALLATION
ELECTRIC INSTALLATIONE
MAINTENANCE AND CLEANING
SERVICE
ENVIRONMENTAL CONSIDERATIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Thermex 10 Wall Mounted Hoods Instruction Manual

WARNINGS

The range hood is designed and manufactured according to DS/EN 60335-1.
This range hood is only for use in private house holdings, if used for other purposes the warranty will be repealed.
Installation must be performed by a skilled electrician in accordance with the specifications given by Thermax Scandinavia A/S (Thermax) and legislation in force.
Thermax disclaims all responsibility in regards to damages caused by wrong installation, mounting or use

BEFORE MOUNTING/COMMISSIONING

Inspect the range hood for transport damages, flaws and defects immediately after the receipt.
Transport damages must be filed to the haulage contractor and Thermax immediately after the receipt.
Flaws and defects must be filed to Thermax within 8 days the receipt, and not later than mounting/commissioning.

MOUNTING

The range hood is intended for working at 230 Volt ±10%~ 50 HZ in referring to EN 50160.
Connect the hood with the attached plug. NOTE: The hood MUST have earth if the plug has an earth connection.
For models with external motor applies that NOT to use common zero by installing the hood and engine, as this will affect the control.
It MUST be ensured that the motor can be used with the selected range hood when using an external motor from another supplier. Otherwise the warranty no longer apply.
Do not plug in the range hood until the mounting is complete.
The air must not be discharged from the hood into a pipe used for extraction from devices using gas or other fuels. Such devices must have a separate vent.

INSTALLATION

Locate keyhole mounting holes on back on hood. Mark on wall with pen.
Drill out marked hole on wall. Drill, screw and rawplug must be chosen in accordance with recommended type for the wall type.
Install rawplug and appropriate screw. Leave out 5 mm, for hood to catch on to.
Hang hood on screws using the keyholes
Install security screw, and fasten keyhole screws. With hood mounted in keyholes.
- Mark security screw holes from inside hood.
- Remove hood, pre-drill holes and reinstall hood.
- Install security screws
- Fasten key hole screws and ensure that the hood is secrurely mounted.
Install duct pipe on top of the hood’s outlet. Ensure that the duct pipe is straight with no bends or obstructions.
Install chimney over the duct hose, and secure on top of hood. If applicable, use included bracket to fasten and secure chimney.

ELECTRIC INSTALLATIONE

MAINTENANCE AND CLEANING

Always disconnect power before cleaning.
The hood must be cleaned regularly to ensure optimal operation and long service life.
Grease and dust debris are collected in the filter and may risk igniting with insufficient cleaning.
The hood should be cleaned inside and out frequently to avoid grease stains on walls or other surfaces.

DAILY CLEANING

For cupboard-integrated, free-hanging and wall-mounted hoods, Thermex recommends that the grease filter be wiped with a damp cloth after each cooking session. It requires very little effort every day to keep your cooker hood clean and effective.
Steel surfaces are cleaned with a damp cloth with detergent and treated with 3M Polish.
Lacquered surfaces should be cleaned with a damp cloth with detergent/washing-up liquid. Never use abrasives.

CLEANING THE GREASE FILTERS
Grease filters should be cleaned as needed. Thermex recommends as a minimum that the filter is cleaned at the following intervals, depending on the fat used for frying:

Frying margarine – filter cleaned every 3 weeks
Liquid margarine – filter cleaned every 2 weeks
Oil – filter cleaned once per week
Deep fat frying – filter cleaned 2-3 times per week
The grease filters are cleaned in the following way:
Open the glass door
Remove the grease filter behind the glass plate and the filter in the base by pulling on the filter-locking mechanism to loosen the filter from the hood.
Place the filters in warm soapy water and clean if necessary with a soft brush.
Rinse with warm water.
Leave the filters to dry on a dishcloth or similar.
Repeat the process if necessary.
Re-attach the filters..

The filters can also be washed in the dishwasher, although please note that machine washing can result in discoloration of the filters. Discoloration of the filters does not affect performance.

REPLACING THE RECIRCULATION FILTERS
If recirculation filters are used, these cannot be washed, but must be replaced when needed. Thermex recommends that the recirculation filters are replaced at least 2-4 times per year.

CONTROL

SERVICE

Before reporting service on your Thermex range hood, it is important that you read the installation and/or user instructions carefully. It ensures that Thermex can provide you the best possible assistance.

Service department at Thermex can be contacted in preparation to:

Technical support for installation and installation of your range hood.
Clarification of functionalities in your hood.
Service Request during the warranty on your hood .

Before a service request during the warranty always try to disconnect the power to the hood for about 5 min. Then plug the power back on to see if the problem is corrected.

If the problem is not corrected, disconnect the power supply to the hood for one hour. If the hood is still not functioning properly, and the troubleshoot – ing charts are reviewed, contact the service department.

NOTE: For inquiries within the warranty, you will be asked for proof of your purchase in the form of a sales receipt. Therefore, always store your sales receipt

Before the request for service within the warranty, it is important to have all the necessary information ready:

Error Description
Model
The type and serial number of the hood (on the chassis plate)
Information of purchase

ENVIRONMENTAL CONSIDERATIONS

PACKAGING
The packaging must be disposed of in accordance with local regulations on waste management. SCRAPPING OF THE PRODUCT

The symbol on the product or accompanying documentation indicates that this product may not be disposed of as household waste but must be delivered to the nearest collection center for the recycling of electrical and electronic equipment.