VEVOR TM-50 Chicken Plucker Machine User Manual
- June 14, 2024
- VEVOR
Table of Contents
VEVOR TM-50 Chicken Plucker Machine
NEED HELP? CONTACT US!
Have product questions? Need technical support? Please feel free to contact
us:
CustomerService@vevor.com
This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.
SAFETY INSTRUCTIONS
For your safety and the safety of others, the following precautions must be observed when operating the chicken plucker machine:
- Ensure the safety of the power supply: install the leakage switch on the grounding wire of the chicken, duck, and goose plucker. Before use, plug in the power supply and turn on the switch to check whether the rotary table operates normally.
- Picking safety: To ensure user’s safety, do not retrieve the bird unless the chicken plucker machine has come to a complete stop.
WARNING:
- Turn off the power when not in use.
- Do not disassemble or change this machine.
- In the operation process, if the machine sounds abnormal, it must be stopped immediately for inspection and continue to work only after the fault is eliminated.
MODEL AND PARAMETERS
| Model | TM-50 |
|---|---|
| Voltage/Frequency | 120V / 60Hz |
| Applicable poultry | Chicken and Duck and Goose |
| Capacity | 2-4 Chickens |
Temperature control switch (overload
protection function)
| 110° temperature control off
Waterproof Rating| IP54
N. Weight| 25.7Kg
G. Weight| 29.65Kg
STRUCTURE DIAGRAM
| No | Parts name |
|---|---|
| 1 | Handle |
| 2 | Finger |
| 3 | Barrel body |
| 4 | Stabilizer blade |
| 5 | Drain connection |
| 6 | Wheel |
| 7 | Leakage protection plug |
| 8 | Switch |
| 9 | Electric motor |
| 10 | High pressure nozzle |
ASSEMBLY AND USE
Step 1: Check all accessories.
**Step 2 : Installation of the drain pipe.
**First, hold both sides of the drain pipe mouth with two hands. Then, aim at the base drain mouth and insert it directly.
Step 3 : Installation of wheels.
Install the wheel on the leg and tighten the screws.
Step 4:Installation of leg with wheels.
First, directly correspond the serial number of the support leg with wheels to the serial number on the baseplate one by one. Then, insert the support leg with wheels into the corresponding baseplate slot, insert the screws, and tighten the nuts onto the screws with a wrench.
Step 5: Installation of handle.
First, put the screws into the holes at both ends of the handle. Then,
insert the screws on the handle into the two screw holes at the barrel mouth.
Finally, lock the screws with nuts inside the barrel and tighten them with a
screwdriver.
Step 6: Connect the plug to the power supply and turn on the machine.
Step 7: The knife edge should be as small as possible when the chicken is
slaughtered.
After slaughter, the chicken should be soaked in warm water (about 30 ℃) to
make feathers wet. It is better to put some salt in warm water to avoid skin
damage due to depilation.
Step 8: Heat the soaked chicken in hot water of about 70 ℃ and stir with
a wooden stick to make it heated evenly.
Step 9: Put 1 to 4 hot chickens in the machine at a time.
Step 10: Press the “1” switch key to start the machine. Water is added to
the poultry while it is running. The feathers and dirt that fall off flow out
with the water. The water can be recycled.
Step 11: After 2-3 minutes, remove the feathers and take out the chicken. Connect the high-pressure nozzle with a water pipe. Spray and rinse off the poultry feathers.
TROUBLESHOOTING INSTRUCTION
| Problem | Reason | Solution |
|---|---|---|
| Incomplete de-feather | Rubber fingers loss | Replace rubber fingers |
Uneven scalding
temperature
| Uniform scalding temperature
chicken plucker machine does not rotate| The power cord is not
plugged in properly
| Plug the power cord
Switch 1 is not pressed| Press switch 1
Locked rotor protection in progress| Remove the obstruction, Wait for 30s.
CLEAN, CARE AND STORAGE RULES
Care and cleaning:
The chicken plucker machine needs to be used with a faucet and a water pipe,
making it convenient for feathers cleaning and keeping the neatness and beauty
of the machine.
The chicken plucker machine is made of stainless steel, which is not easy to
rust. After use, please clean it with tap water and wipe it.
Timely cleaning: After use, the bucket should be washed with water, but not
directly with a water spray pipe. The feathers and dirt that have been removed
should be collected with the water flow and treated in time to avoid
environmental pollution or harm to human health. Water can be recycled, but it
should be removed in time when not in use.
Storage :
Please store it out of the reach of children.
When the chicken plucker machines are not used for a long time, they should be
stored in a dry, non-corrosive environment. Do not contact corrosive
substances to avoid product damage.
Manufacturer: Zibo Shengyan Agricultural and Animal Husbandry Equipment
Factory
Add: East Side of Qiancao Village, Yucheng Town, Boshan District, Zibo
City, Shandong Province
Made in China
Customer Support
TOUGH TOOLS, HALF PRICE
Support and E-Warranty Certificate
https://www.vevor.com/support
We continue to be committed to offering tools at competitive prices. “Save
Half”, “Half Price”, or any other similar expressions used by us only
represent an estimate of savings you might benefit from buying certain tools
with us compared to the major top brands and do not necessarily mean to cover
all categories of tools offered by us. You are kindly reminded to verify
carefully when placing an order with us if you are saving half in comparison
with the top major brands.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>